{"title":"Lighting controls","description":"\u003ch2\u003eLighting controls: managing a boat's lighting circuits\u003c\/h2\u003e\n\u003cp\u003eLighting controls are used to command, adjust, organize, or monitor the lights installed on board. They can range from very simple, such as a dimmer for a cockpit area, to much more complex systems with hubs, interfaces, screens, and zone-based control. The right choice depends on the type of lighting, the vessel's voltage, the current consumed, and the desired level of control.\u003c\/p\u003e\n\u003cp\u003eThis collection includes two main families: Blue Sea Deckhand dimmers for DC circuit dimming, and Garmin\/Lumishore modules for more advanced lighting installations, particularly EOS, SUPRA, i-Connect, or DMX systems. It caters to both simple setups and boats with multiple lighting zones to coordinate.\u003c\/p\u003e\n\u003ch3\u003eDimmers for 12 V and 24 V circuits\u003c\/h3\u003e\n\u003cp\u003eA dimmer allows you to adjust light intensity without replacing fixtures. This is useful in a cockpit, cabin, helm station, or night watch area where you want to switch from functional lighting to softer lighting. The \u003ca href=\"\/en-us\/products\/blue-sea-variateur-deckhand-12v-cc-12a-gradateur-marin\" title=\"Blue Sea Deckhand 12 V DC 12 A dimmer\"\u003eBlue Sea Deckhand 12 V DC 12 A dimmer\u003c\/a\u003e meets this need for 12 V circuits requiring higher output capacity. For smaller loads, the \u003ca href=\"\/en-us\/products\/blue-sea-variateur-deckhand-12v-dc-6a-eclairage-marin\" title=\"Blue Sea Deckhand 12 V DC 6 A dimmer\"\u003eDeckhand 12 V DC 6 A\u003c\/a\u003e may be more suitable.\u003c\/p\u003e\n\u003cp\u003e24 V installations have equivalent options: the \u003ca href=\"\/en-us\/products\/blue-sea-variateur-deckhand-24v-12a\" title=\"Blue Sea Deckhand 24 V 12 A dimmer\"\u003eDeckhand 24 V 12 A\u003c\/a\u003e and the \u003ca href=\"\/en-us\/products\/blue-sea-variateur-deckhand-24v-6a\" title=\"Blue Sea Deckhand 24 V 6 A dimmer\"\u003eDeckhand 24 V 6 A\u003c\/a\u003e. The choice between 6 A and 12 A is based on the total current of the controlled fixtures, with a reasonable margin. Compatibility with the type of lighting must also be verified: LED, halogen, incandescent, or already regulated circuits.\u003c\/p\u003e\n\u003cp\u003eThe \u003ca href=\"\/en-us\/products\/blue-sea-deckhand-dimmer-controleurs-eclairage\" title=\"Deckhand Dimmer lighting controllers by Blue Sea\"\u003eDeckhand Dimmer\u003c\/a\u003e follows the same local control logic: a clear interface, smooth dimming, and marine-grade mounting. For such products, the most important factors are correctly sizing the circuit and ensuring the control is accessible from the usage area.\u003c\/p\u003e\n\u003ch3\u003eHubs, interfaces, and zone-based systems\u003c\/h3\u003e\n\u003cp\u003eFor more complex underwater or decorative lighting installations, a simple dimmer is not always sufficient. Hubs and interfaces allow you to control multiple fixtures, manage zones, connect modules, or integrate advanced control. The \u003ca href=\"\/en-us\/products\/garmin-eos-i-connect-hub-kit-eclairage-sous-marin\" title=\"i-Connect EOS hub kit with 1 m DMX cable\"\u003ei-Connect EOS hub kit\u003c\/a\u003e and the \u003ca href=\"\/en-us\/products\/garmin-supra-i-connect-hub-kit-eclairage-marin\" title=\"i-Connect SUPRA hub kit with 4 connectors and 1 m DMX cable\"\u003ei-Connect SUPRA hub kit\u003c\/a\u003e help structure such installations.\u003c\/p\u003e\n\u003cp\u003eThe SUPRA family also includes the \u003ca href=\"\/en-us\/products\/lumishore-kit-hub-i-connect-supra-cable-dmx\" title=\"i-Connect SUPRA hub kit with DMX cable\"\u003ei-Connect SUPRA hub kit with DMX cable\u003c\/a\u003e, the \u003ca href=\"\/en-us\/products\/lumishore-supra-smx-lumi-hub-controleur-eclairage-marin\" title=\"SUPRA SMX Lumi-Hub lighting control hub\"\u003eSUPRA SMX Lumi-Hub\u003c\/a\u003e, and the \u003ca href=\"\/en-us\/products\/lumishore-supra-bridge-module-interface-eclairage\" title=\"SUPRA Bridge Module lighting interface\"\u003eSUPRA Bridge Module\u003c\/a\u003e. These products are designed for installations where spotlights, underwater lights, or fixtures must operate as a system rather than isolated lamps.\u003c\/p\u003e\n\u003ch3\u003eScreens and control centers\u003c\/h3\u003e\n\u003cp\u003eWhen lighting becomes a central function on the boat, the control interface is as important as the modules. The \u003ca href=\"\/en-us\/products\/garmin-ecran-eos-lux-supra-controleur-eclairage-marin\" title=\"EOS LUX SUPRA screen lighting controller\"\u003eEOS LUX SUPRA screen\u003c\/a\u003e and the \u003ca href=\"\/en-us\/products\/garmin-centre-commande-eos-lux-eclairage-marin\" title=\"EOS LUX control center lighting\"\u003eEOS LUX control center\u003c\/a\u003e allow you to consolidate control in a dedicated interface. This is useful when multiple zones, colors, or scenarios need to remain simple for the crew to use.\u003c\/p\u003e\n\u003cp\u003eThe \u003ca href=\"\/en-us\/products\/garmin-kit-installation-i-connect-supra-thx-tix-hub-interrupteur\" title=\"i-Connect SUPRA THX\/TIX installation kit with switch and hub\"\u003ei-Connect SUPRA THX\/TIX installation kit with switch and hub\u003c\/a\u003e is relevant when the need focuses on both integration and control. In this case, the entire installation must be planned: compatible fixtures, cables, hubs, switches, module locations, and future access for maintenance.\u003c\/p\u003e\n\u003ch3\u003eKey selection criteria before installation\u003c\/h3\u003e\n\u003cp\u003eThe first criterion is the vessel's voltage: 12 V or 24 V. The second is the total current of the circuit. Add up the consumption of the controlled fixtures and choose an appropriately sized controller, avoiding continuous operation at maximum capacity. Next, verify dimming compatibility: not all LEDs respond the same way to a dimmer, especially if they already include regulation electronics.\u003c\/p\u003e\n\u003cp\u003eFor zone-based systems, start with the boat's layout. Which zones should be controlled together? Which zones should remain separate? Is local control, a central screen, a DMX interface, or a specific hub required? A good lighting system must be understandable at the helm, well-documented, and easy to troubleshoot.\u003c\/p\u003e\n\u003ch3\u003eComplementary collections\u003c\/h3\u003e\n\u003cp\u003eTo complete your installation, also consult the \u003ca href=\"\/en-us\/collections\/eclairage\" title=\"Boat lighting\"\u003elighting\u003c\/a\u003e, \u003ca href=\"\/en-us\/collections\/lumieres-de-courtoisie\" title=\"Boat courtesy lights\"\u003ecourtesy lights\u003c\/a\u003e, and \u003ca href=\"\/en-us\/collections\/projecteur\" title=\"Boat spotlights\"\u003espotlights\u003c\/a\u003e collections. Lighting controls should be chosen in conjunction with the fixtures they will operate, not separately.\u003c\/p\u003e\n\u003ch3\u003eSkysat advice\u003c\/h3\u003e\n\u003cp\u003eStart by mapping the lighting zones and electrical loads, then select the control system. For a simple circuit, a properly sized dimmer is often sufficient. For underwater lights or spotlights controlled by zones, prioritize a consistent hub + interface architecture, with clearly identified cables, protections, and documentation.","products":[{"product_id":"garmin-centre-commande-eos-lux-eclairage-marin","title":"EOS LUX Control Center","description":"\u003cp\u003eThe \u003cstrong\u003eGarmin EOS LUX Control Center\u003c\/strong\u003e, also known as the Lumishore Lumi-Link™ Command Center, is a central interface designed for unified and sophisticated management of Lumishore marine lighting systems. This module allows control of all Lumishore SMX, THX, and TIX EOS underwater lights, as well as Lumishore Lux deck lighting systems, directly from a compatible multifunction display (MFD) or a device connected via Wi-Fi. It provides a key integration solution for modern marine installations, reducing dashboard clutter while offering advanced control flexibility.\u003c\/p\u003e\n\n\u003ch3\u003eExtended Integration and Compatibility\u003c\/h3\u003e\n\u003cp\u003eThis control center stands out for its extensive compatibility with MFDs from major manufacturers. It integrates natively with Garmin systems via OneHelm, Raymarine Axiom displays with the Lighthouse Partner app, Navico MFDs (Simrad NSO EVO3\/EVO2, NSS EVO3\/Go, B\u0026G Zeus3 Glass Helm, Zeus3, Vulcan), and the Furuno Navnet TZ Touch 3 series. This versatility ensures a consistent user experience, allowing Lumishore lighting to be managed as an extension of the main navigation system. The Lumi-Link™ interface is a unique API that facilitates plug-and-play integration with a single cable, significantly simplifying installation and configuration compared to proprietary solutions.\u003c\/p\u003e\n\n\u003ch3\u003eAdvanced Features and Marine Robustness\u003c\/h3\u003e\n\u003cp\u003eThe \u003cstrong\u003eGarmin EOS LUX Control Center\u003c\/strong\u003e offers complete control over lighting, including RGB spectrum and adjustable white color temperature from 2700K to 6500K. It enables configurable management of lighting zones and the creation of custom lighting scenes. Adjustable color cycle modes (Spectrum, Ice, Sunset, Miami) and sweep modes (Ice, Sunset, Miami) are complemented by fixed or dynamic strobe functions and a \"Sound to Light\" mode. Integrated diagnostics and \"Over the Air\" software updates ensure easy maintenance. Designed for the marine environment, the device features IP67 protection and a robust ABS construction resistant to weather conditions (flame-retardant and halogen-free), with a supply voltage range of 10.5 to 31 V DC and a maximum consumption of 0.5 A. Its compact dimensions (113 x 61 x 33 mm) facilitate discreet installation on board.\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":55860481753428,"sku":"010-04360-00","price":811.78,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/main_46f2b599-f04d-482b-8390-e98e3c9b51c5.jpg?v=1779194034"},{"product_id":"garmin-ecran-eos-lux-supra-controleur-eclairage-marin","title":"EOS LUX SUPRA Screen","description":"\u003cp\u003e\n    The \u003cstrong\u003eGarmin EOS LUX SUPRA screen\u003c\/strong\u003e (SKU 010-04362-00) is a dedicated control screen designed for intuitive management of Lumishore LUX and EOS marine lighting systems, whether submersible or surface-mounted. This device acts as a centralized control point, providing a physical interface for managing onboard lighting features. It differs from solutions integrated into multifunction displays (MFD) such as Garmin OneHelm or Raymarine Axiom, as well as smartphone control, by offering a user interface optimized specifically for lighting.\n\u003c\/p\u003e\n\u003ch3\u003eAdvanced Control and Customization\u003c\/h3\u003e\n\u003cp\u003e\n    The screen features a color touch panel and a rotary knob, enabling quick and precise adjustments. It allows for color changes (full RGB spectrum, white temperatures from 2700K to 6500K), brightness adjustment, and selection of configurable lighting zones. The system supports dynamic modes including strobe, sweep, color cycling (Spectrum, Ice, Sunset, Miami), and sound-light effects. Customization enables creating custom lighting scenes, adjusting sensitivity, and managing multiple zones independently. Unlike an MFD interface that groups various functions, this screen provides direct and simplified access to lighting controls.\n\u003c\/p\u003e\n\u003ch3\u003eInstallation and Connectivity\u003c\/h3\u003e\n\u003cp\u003e\n    Designed for flush-mount installation via panel mounting, the screen requires a depth of 94 mm and has a front protrusion of 10 mm. Its mounting dimensions are 83 mm x 83 mm. The construction combines a glass front and a molded polymer back, with an IP68 rating for water and dust resistance. The system is powered by a voltage range of 10.5 to 31 VDC, with an average consumption of 3.6 W (0.3 A at 12 V, 0.15 A at 24 V). Connectivity is via an Ethernet cable. Additionally, integrated Wi-Fi functionality allows control of the system from a smartphone or tablet, providing increased flexibility for onboard users. The device comes with a 3-year warranty. It is compatible with all SMX, THX, and TIX EOS underwater lighting systems, as well as Lumishore Lux surface lighting systems.\n\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":55860483227988,"sku":"010-04362-00","price":431.03,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/main_490061eb-3dfc-4a02-afe2-96d0fc47216d.jpg?v=1779194052"},{"product_id":"blue-sea-variateur-deckhand-24v-6a","title":"Deckhand Dimmer - 24 V DC 6 A","description":"\u003cp\u003e\n    Designed to optimize onboard lighting, the BLUE SEA Deckhand 7504-BSS dimmer is a digital solution for controlling light intensity in 24 V DC systems. It manages unregulated LEDs, incandescent bulbs, and halogen lamps. Its illuminated output feature offers an adjustable delay for safety during boarding and disembarking, with settings from 1 to 5 minutes. The dimmer supports multiple switch locations and includes memory for the last brightness setting.\n\u003c\/p\u003e\n\u003ch3\u003eFeatures and performance\u003c\/h3\u003e\n\u003cp\u003e\n    The integrated \"bulb saver\" extends bulb lifespan during boat battery charging. Offset mounting tabs allow side-by-side installation of multiple dimmers, optimizing space in the electrical panel. Built-in overcurrent protection ensures circuit safety; the system can be reset by holding the dimmer switch until the circuit flashes.\n\u003c\/p\u003e\n\u003ch3\u003eTechnical specifications and compliance\u003c\/h3\u003e\n\u003cp\u003e\n    Operating at a nominal voltage of 24 V DC with an operating range of 18 V to 32 V, the Deckhand 7504 delivers a maximum output current of 6 A. Its standby current is less than 2 mA, and it operates across an extended temperature range of −40°C to 85°C. Brightness control is achieved via pulse-width modulation (PWM), ensuring smooth dimming. This product complies with E, ISO 8846, and SAE J1171 standards for external ignition protection, confirming its reliability in marine environments.\n\u003c\/p\u003e\n\u003ch3\u003ePositioning within the BLUE SEA range\u003c\/h3\u003e\n\u003cp\u003e\n    In BLUE SEA’s Deckhand range, the 7504 model is the 24 V DC 6 A reference. It complements the 12 V DC versions, such as the 7506 (6 A), 7507 (12 A), and 7508 (25 A), as well as other higher-power 24 V DC models like the 7509 (12 A). This dimmer is designed to replace earlier references such as the 7501 or 7502 models, offering improved current and feature performance for 24 V systems.\n\u003c\/p\u003e","brand":"Blue Sea Systems","offers":[{"title":"","offer_id":55906818589012,"sku":"7504-BSS","price":85.25,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/01_-_Hero_-_BLUE_SEA_Deckhand_Dimmer_-_24V_DC_6A_7504-BSS_-_Ref_283a18df.jpg?v=1779398048"},{"product_id":"blue-sea-variateur-deckhand-12v-dc-6a-eclairage-marin","title":"Deckhand Dimmer - 12 V DC 6 A","description":"\u003cp\u003e\n    Designed for marine lighting control, the BLUE SEA SYSTEMS Deckhand 7506-BSS dimmer provides precise digital control of light intensity. This unit is compatible with unregulated LED, incandescent, and halogen lighting operating at a nominal voltage of 12 V DC, with an operating range from 9 V to 16 V.\n\u003c\/p\u003e\n\u003ch3\u003eTechnical Features and Performance\u003c\/h3\u003e\n\u003cp\u003e\n    The Deckhand 7506-BSS dimmer uses continuous pulse-width modulation (PWM) for smooth 0–100 % input voltage adjustment. Maximum output is 6 A, with standby current below 2 mA. Operating temperature range is -40 °C to 85 °C. A bulb-saver function prevents premature lamp aging during system charging. The unit stores the last brightness setting and features a backlit output with adjustable 1–5 minute delay for easy exit. Offset mounting tabs allow close installation of multiple dimmers, and it ships with a momentary (ON)-OFF-(ON) switch.\n\u003c\/p\u003e\n\u003ch3\u003ePositioning and Compliance\u003c\/h3\u003e\n\u003cp\u003e\n    The Deckhand 7506-BSS dimmer is a versatile lighting-control solution for low- to mid-power marine circuits. In the Deckhand line, it is the lowest-power 12 V DC option (6 A), complemented by 7507 (12 A) and 7508 (25 A) for higher loads, plus 24 V DC versions (7504, 7509). It meets ignition-protection standards ISO 8846 and SAE J1171, and carries the CE mark, ensuring reliability and safety in marine environments. It replaces earlier 7501 or 7502 models from the brand, offering improved functionality in a footprint of 82.55 mm width by 88.9 mm height.\n\u003c\/p\u003e","brand":"Blue Sea Systems","offers":[{"title":"","offer_id":55906878390612,"sku":"7506-BSS","price":81.95,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/01_-_Hero_-_BLUE_SEA_Deckhand_Dimmer_-_12V_DC_6A_7506-BSS_-_Ref_1af86a8b.jpg?v=1779398311"},{"product_id":"blue-sea-variateur-deckhand-12v-cc-12a-gradateur-marin","title":"Deckhand Dimmer - 12 V DC 12 A","description":"\u003cp\u003e\n    Designed for precise control of onboard lighting, the BLUE SEA SYSTEMS Deckhand PN 7507 dimmer manages digital dimming of unregulated LEDs, incandescent, and halogen lights. This device integrates technical features to optimize user experience and the longevity of lighting equipment. It provides continuous control via pulse-width modulation (PWM) from 0 to 100% of the input voltage, ensuring smooth transitions in light intensity.\n\u003c\/p\u003e\n\u003ch3\u003eFeatures and technical specifications\u003c\/h3\u003e\n\u003cp\u003e\n    The Deckhand 7507 dimmer operates at a nominal voltage of 12V DC, with an extended operating range from 9V to 16V. It supports a maximum output current of 12A and features standby current below 2mA, making it energy-efficient. Its operating temperature range, from -40°C to 85°C, demonstrates its robustness in various marine environments. Key features include a backlit output with adjustable delay up to 5 minutes, a memory function for the last dimming setting, and a bulb saver to prevent premature aging during boat battery charging. Offset mounting tabs facilitate installation of multiple dimmers side by side, and a momentary (ON)-OFF-(ON) switch is included for intuitive use. The product complies with CE, ISO 8846, and SAE J1171 standards for ignition protection.\n\u003c\/p\u003e\n\u003ch3\u003ePositioning within the range and applications\u003c\/h3\u003e\n\u003cp\u003e\n    The 7507 model is part of the BLUE SEA SYSTEMS Deckhand series, offering a 12A capacity at 12V DC. It serves as an intermediate solution in terms of current, complementing the 7506 (6A) and 7508 (25A) models for different power needs in 12V systems. For 24V systems, equivalents such as the 7509 (12A) are also available. This range is designed for managing general onboard lighting, from cabins to cockpits, where light intensity adjustment is required for comfort or night navigation. Its compatibility with unregulated LEDs, incandescent, and halogen bulbs makes it a versatile choice for modernizing or equipping existing lighting systems.\n\u003c\/p\u003e","brand":"Blue Sea Systems","offers":[{"title":"","offer_id":55906942353748,"sku":"7507-BSS","price":92.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/01_-_Hero_-_BLUE_SEA_Deckhand_Dimmer_-_12V_DC_12A_7507-BSS_-_Ref_9db88dba.jpg?v=1779398585"},{"product_id":"blue-sea-variateur-deckhand-24v-12a","title":"Deckhand Dimmer - 24 V DC 12 A","description":"\u003cp\u003e\n    Designed for 24 V DC marine systems, the BLUE SEA Deckhand 7509 dimmer is a digital lighting management solution. It provides precise control of light intensity for unregulated LEDs, incandescent, and halogen bulbs. This dimmer features a backlit output with an adjustable delay of 1 to 5 minutes, offering enhanced safety during disembarkation.\n\u003c\/p\u003e\n\n\u003ch3\u003eTechnical Specifications and Features\u003c\/h3\u003e\n\u003cp\u003e\n    The Deckhand 7509 includes memory for the last intensity setting and supports multiple switching locations. Its \"bulb saver\" function protects bulbs from premature aging when the boat's batteries are charging. Offset mounting tabs optimize installation by allowing multiple dimmers to be mounted close together. A momentary (ON)-OFF-(ON) switch is included for immediate use. It features built-in overload protection, resettable via a simple switch manipulation.\n\u003c\/p\u003e\n\n\u003ch3\u003eIntegration and Compliance\u003c\/h3\u003e\n\u003cp\u003e\n    With a nominal voltage of 24 V DC and an operating range of 18 V to 32 V, this dimmer handles a maximum output current of 12 A with a standby current of less than 2 mA. It operates within an extended temperature range of −40°C to 85°C and uses pulse-width modulation (PWM) control. The Deckhand 7509 dimmer complies with E-marked regulatory standards, ISO 8846 and SAE J1171 for external ignition protection, as well as SAE J1455 and SAE J1113. Within the BLUE SEA Deckhand range, the 7509 model is the 24 V DC 12 A dimmer, offering superior load management compared to the 7504 model (6 A at 24 V DC) and differing from 12 V DC versions such as the 7507 (12 A) or 7508 (25 A).\n\u003c\/p\u003e","brand":"Blue Sea Systems","offers":[{"title":"","offer_id":55907044589908,"sku":"7509-BSS","price":102.14,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/01_-_Hero_-_BLUE_SEA_Deckhand_Dimmer_-_24V_DC_12A_7509-BSS_-_Ref_ff14aeb7.jpg?v=1779398851"},{"product_id":"lumishore-supra-smx-lumi-hub-controleur-eclairage-marin","title":"SUPRA SMX Lumi-Hub lighting control hub","description":"\u003cp\u003e\n    Designed for centralized management of underwater lighting systems, the \u003cstrong\u003eLumishore SUPRA SMX Lumi-Hub\u003c\/strong\u003e is a junction box dedicated to Lumishore SMX53 series lights. It simplifies installation and control of these fixtures, providing an integrated solution for vessels requiring high-performance underwater lighting.\n\u003c\/p\u003e\n\u003ch3\u003eIntegration and technical performance\u003c\/h3\u003e\n\u003cp\u003e\n    The Lumi-Hub operates with an input voltage of 10 to 31VDC, ensuring broad compatibility with marine electrical systems. Measuring 151mm x 85mm x 70mm (with cover), its black thermoplastic housing offers IP68 protection, guaranteeing waterproofing against prolonged immersion. Each Lumi-Hub supports up to four SMX53 lights, with a maximum output current of 5A per light and a maximum input current of 20A. Connections are made via screw terminals, and the system includes reverse polarity protection and an anti-noise filter. Each light is individually protected by replaceable blade fuses, simplifying maintenance and troubleshooting. It comes with a 2-year warranty.\n\u003c\/p\u003e\n\u003ch3\u003eFeatures and system scalability\u003c\/h3\u003e\n\u003cp\u003e\n    The \u003cstrong\u003eLumishore SUPRA SMX Lumi-Hub\u003c\/strong\u003e is designed for plug-and-play installation, centralizing all light and switch connections. It is compatible with the SUPRA i-Connect switch for full lighting mode control (color changes, strobe, fade, effect synchronization). For advanced integration, it can connect to a Lumi-Link Bridge module to enable direct control from compatible multifunction displays (MFD), such as Garmin OneHelm™ systems. Status LEDs for each light facilitate diagnostics. The system is scalable: up to four Lumi-Hubs can be daisy-chained, allowing control of up to 16 lights. This modularity makes it suitable for installations of varying sizes, from pleasure craft to larger yachts, offering superior flexibility compared to direct wiring systems. Note that this hub is not compatible with SMX23 lights.\n\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":55967523995988,"sku":"010-04354-00","price":165.22,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/01_8f553801-2efd-4322-9c88-1e7810a2f770.jpg?v=1779970815"},{"product_id":"garmin-supra-i-connect-hub-kit-eclairage-marin","title":"i-Connect SUPRA Hub Kit - 4 connectors and 1 m DMX cable","description":"\u003cp\u003e\n    Designed to optimize the installation and control of Lumishore SUPRA underwater lighting, the Garmin SUPRA i-Connect Hub Kit is a centralized junction point. This hub supports up to four lights from the SMX, THX, and TIX series, except for SMX23 models. It is compatible with 12V and 24V onboard electrical systems, accepting an input voltage of 10 to 31V DC with a maximum current of 40A. Each light output or zone handles a maximum current of 10A.\n\u003c\/p\u003e\n\u003ch3\u003eIntegration and Robustness\u003c\/h3\u003e\n\u003cp\u003e\n    The SUPRA i-Connect Hub Kit is built with robust, weather-resistant ABS plastic and features an IP68 rating for protection against prolonged immersion. Its compact dimensions of 148 mm x 79 mm x 38 mm facilitate installation. The kit includes four field-installable connectors and a 1-meter DMX cable, enabling plug-and-play implementation. Integrated functions include full light synchronization, a switching power relay, individual and replaceable blade fuses for each light, status LED indicators for quick troubleshooting, noise filtering, and reverse polarity protection.\n\u003c\/p\u003e\n\u003ch3\u003eAdvanced Control and Scalability\u003c\/h3\u003e\n\u003cp\u003e\n    This hub stands out from generic DMX solutions with its design specifically for Lumishore SUPRA lighting, ensuring optimal compatibility and advanced features such as light synchronization and direct integration with Garmin OneHelm™ multifunction displays via the Lumi-Link module. While other systems may require complex interfaces or dedicated controllers, the SUPRA i-Connect Hub Kit simplifies the lighting network architecture. Control is achieved via a momentary switch, a SUPRA Bridge module, or directly from compatible MFDs via a Lumi-Link Bridge module. It supports various lighting modes (colors, strobe, fade) and is scalable: multiple hubs can be daisy-chained to control up to 16 SMX lights (with four hubs) or up to 64 THX\/TIX lights (with 16 hubs), offering great flexibility for large-scale installations. A 3-year warranty accompanies this product.\n\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":55967525273940,"sku":"010-04356-00","price":166.05,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/01_84dcaf11-ab63-41a1-aaca-1030e5338fc2.jpg?v=1779970833"},{"product_id":"garmin-eos-i-connect-hub-kit-eclairage-sous-marin","title":"Garmin EOS i-Connect Hub Kit with 1 m DMX cable","description":"\u003cp\u003e\n    Designed for managing underwater lighting systems, the \u003cstrong\u003eGarmin EOS i-Connect Hub Kit\u003c\/strong\u003e is an interface dedicated to Lumishore EOS underwater lights. This hub enables full control of EOS color-changing underwater lights via the EOS-LUX control center or compatible multifunction displays (MFD) equipped with Lumi-Link integration. It serves as a central component for sophisticated lighting installations, providing an integrated solution for sport sailboats, cruisers, yachts, and superyachts using Lumishore TIX 40 or SMX 154 lights.\n\u003c\/p\u003e\n\n\u003ch3\u003eCapabilities and System Integration\u003c\/h3\u003e\n\u003cp\u003e\n    Each hub can manage up to 4 EOS color-changing underwater lights. For larger installations, it is possible to connect up to 4 hubs on the same vessel, allowing control of a total of 16 lights, whether surface-mounted or through-hull. The \u003cstrong\u003eGarmin EOS i-Connect Hub Kit\u003c\/strong\u003e operates within a voltage range of 10.5 to 31V DC, with a maximum input current of 20 A and an output current of 5 A per light. It integrates switching relays for efficient power management.\n\u003c\/p\u003e\n\n\u003ch3\u003eInstallation and Reliability\u003c\/h3\u003e\n\u003cp\u003e\n    Hub installation is simplified with plug-and-play connections. For maintenance and diagnostics, each light connection is equipped with a status LED indicator. The system protects each light with a replaceable blade fuse and includes reverse polarity protection, as well as noise filtering for stable operation. Its robust ABS construction, halogen-free and flame-retardant, combined with IP68 certification, ensures resistance to demanding marine environments. The kit includes a 1-meter DMX cable for interconnection.\n\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":55967525863764,"sku":"010-04357-00","price":107.75,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/01_616ac9af-c038-4ca9-85aa-ec4eac71afbc.jpg?v=1779970851"},{"product_id":"garmin-kit-installation-i-connect-supra-thx-tix-hub-interrupteur","title":"Garmin i-Connect SUPRA THX\/TIX installation kit with switch and hub","description":"\u003cp\u003e\n    The Garmin i-Connect SUPRA THX\/TIX 010-04358-00 installation kit is an essential component for controlling Lumishore bi-color underwater lights from the THX and TIX series. It also offers optional compatibility with SMX54 bi-color lights. Designed for simplified integration and centralized management, this kit allows you to control up to four projectors per hub, with the possibility of installing up to 16 hubs per boat for THX\/TIX systems (up to 64 lights) and up to 4 hubs for SMX systems (up to 16 lights) for extended lighting configurations.\n\u003c\/p\u003e\n\n\u003ch3\u003eFeatures and Technical Performance\u003c\/h3\u003e\n\u003cp\u003e\n    This kit operates within a voltage range of 10.5 to 31V DC, with a maximum input current of 40 A and a maximum output current of 10 A per connected light. The design ensures IP68 protection against dust and prolonged immersion, ensuring reliability in marine environments. Installation is simplified with plug-and-play connections and field-installable IP68 connectors. For safety, integrated and replaceable blade fuses are included for each individual light. Power can be supplied from a DC source or an AC\/DC power supply, with an AC hub option available for THX\/TIX systems.\n\u003c\/p\u003e\n\n\u003ch3\u003eAdvanced Integration and Control\u003c\/h3\u003e\n\u003cp\u003e\n    The kit includes a control switch to toggle between different lighting modes, including colors, strobe effects, and fade transitions. For more sophisticated control, the system is fully compatible with certified multifunction displays (MFD), including Garmin OneHelm™ MFDs, by adding a SUPRA Bridge module (sold separately). Each light connection on the hub has a status LED for quick diagnostics. Full light synchronization, an integrated noise filter, and reverse polarity protection complete the technical features of this system, ensuring stable and secure operation. Compared to more basic underwater lighting systems, this Garmin kit, while dedicated to Lumishore lights, positions itself as an advanced integration solution, offering network and diagnostic capabilities typically reserved for complex navigation equipment.\n\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":55967526519124,"sku":"010-04358-00","price":371.33,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/01_2b17c731-73a4-43ca-b2ce-dc7413a2da5e.jpg?v=1779970869"},{"product_id":"lumishore-kit-hub-i-connect-supra-cable-dmx","title":"i-Connect hub kit with 1 m DMX cable","description":"\u003cp\u003e\n    Designed to centralize control of Lumishore underwater lighting systems, the Lumishore i-Connect hub kit with 1 m DMX cable (SKU 010-04359-00) is a dedicated interface for managing SUPRA (dual-color) THX or TIX lights. This kit efficiently controls compatible lighting, providing an integrated solution for recreational boaters and professionals. This kit is the SUPRA i-Connect hub, designed for dual-color THX, TIX, or SMX lights.\n\u003c\/p\u003e\n\u003ch3\u003eSystem Capabilities and Extensibility\u003c\/h3\u003e\n\u003cp\u003e\n    Each i-Connect hub can control up to 4 underwater lights. For SUPRA systems, up to 16 hubs can be installed for THX and TIX lights, and up to 4 hubs for SMX lights. The system operates within a voltage range of 10.5–31 VDC, compatible with 12 V and 24 V DC installations, with a maximum current draw of 0.2 A at 12 V for the SUPRA hub alone and a maximum current of 40 A (10 A per zone) for the hub.\n\u003c\/p\u003e\n\u003ch3\u003eRobust Design and Advanced Features\u003c\/h3\u003e\n\u003cp\u003e\n    The i-Connect hub kit features a robust ABS construction, weather-resistant, flame-retardant, and halogen-free, ensuring durability in marine environments. Its IP68 rating provides full protection against water and dust for the hub and its connections. It includes a power switching relay, noise-filtering for clear signal transmission, and reverse polarity protection. Each connected light has a replaceable blade fuse and a dedicated status LED. The SUPRA hub dimensions are 148 mm wide, 79 mm deep, and 38 mm high. Control is possible via a momentary switch; for integration with multifunction displays (MFD), a SUPRA Bridge module can be added for SUPRA systems.\n\u003c\/p\u003e\n\u003ch3\u003ePositioning and Benefits\u003c\/h3\u003e\n\u003cp\u003e\n    Unlike generic DMX controllers, this hub is optimized for Lumishore products, ensuring seamless integration and specific features such as individual light protection via fuse and status feedback. The included 1-meter DMX cable is used to connect Lumishore driver modules in series or extend cable lengths. This system offers a plug-and-play solution simplifying the installation of a sophisticated lighting network.\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":55967527305556,"sku":"010-04359-00","price":345.26,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/01_39061e09-1a8a-4f18-a5e4-dd2db2c19338.jpg?v=1779970887"},{"product_id":"lumishore-supra-bridge-module-interface-eclairage","title":"SUPRA Bridge Module, Bridge Module","description":"\u003cp\u003e\n    Designed for seamless integration of underwater lighting systems, the Garmin SUPRA Bridge Module (010-04361-00) is an ultra-compact device for controlling Lumishore SUPRA bicolor underwater lights. This module serves as the essential gateway to operate all Lumishore SUPRA lighting features by connecting via the Data IN port of a SUPRA Hub and integrating with the boat’s Ethernet network or via Wi-Fi.\n\u003c\/p\u003e\n\n\u003ch3\u003eExtended integration and compatibility\u003c\/h3\u003e\n\u003cp\u003e\n    The SUPRA Bridge Module is a multi-platform solution that allows control of lighting via a compatible multifunction display (MFD), a dedicated Lumishore SUPRA Display screen, or a smart device (smartphone\/tablet) via Wi-Fi. Compatibility extends to Garmin MFDs (OneHelm Enabled), Raymarine Axiom (Lighthouse Partner App), Navico (Simrad NSO EVO3\/EVO2, NSS EVO3\/Go**, B\u0026G Zeus3 Glass Helm\/Zeus3\/Vulcan), and Furuno (models to be confirmed). This versatility enables centralized management of Lumishore SUPRA lighting directly from the boat’s primary navigation interface. The system auto-configures all connected lighting installations at startup, and multiple modules can be used to create independent lighting zones, offering flexibility for complex setups.\n\u003c\/p\u003e\n\n\u003ch3\u003eDesign and installation\u003c\/h3\u003e\n\u003cp\u003e\n    Operating on 12\/24V DC power (input 10–31V), the module features a robust ABS weather-resistant housing (flame-retardant and halogen-free) with an IP68 waterproof rating. It must be mounted in a dry location on a flat surface, away from heat sources or vibrations. An SD card slot is accessible for future software updates. Connection to the SUPRA Hub is via a 3-pin M12 data output connector, extendable with 1m, 5m, or 15m DMX extension cables. For MFD connections, brand-specific conversion cables are required (e.g., Garmin conversion cable PN: 60-0372, Raynet to Raymarine RJ45 cable PN: A80151, Navico conversion cable PN: 60-0373). An IP67 RJ45 protection kit (39-0235) is included to ensure waterproof Ethernet connections.\n\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":55967528354132,"sku":"010-04361-00","price":229.88,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/01_60cbc32c-c9a9-4920-829d-5d8b9adf60c0.jpg?v=1779970904"},{"product_id":"garmin-lux-sl-driver-bande-lumineuse-marine","title":"LUX SL Driver, driver for LED light strips","description":"\u003cp\u003e\n    Designed specifically for the Lumishore LUX marine lighting ecosystem, the \u003cstrong\u003eGarmin LUX SL driver\u003c\/strong\u003e (010-04438-00) is an essential regulation module for LED light strips and flexible neon lights. It provides stable and reliable power, crucial for the longevity and performance of onboard LED lighting systems.\n\u003c\/p\u003e\n\u003ch3\u003eVoltage stability and compatibility\u003c\/h3\u003e\n\u003cp\u003e\n    This driver includes a voltage stabilizer that supports a wide input range of 10.5 to 31 volts DC, making it compatible with 12V and 24V onboard electrical systems. It delivers a stabilized 24-volt output, protecting the lighting from common voltage fluctuations in marine environments. Unlike generic drivers, the LUX SL Driver is optimized for Lumishore LUX lighting products only, ensuring optimal integration and performance while maintaining warranty validity. It can power up to 10 meters of LED strip (two 5-meter maximum outputs), with a maximum power output of 68 watts. Typical consumption is 5.6A at 12V and 2.8A at 24V, requiring a 7.5A fuse for 12V installations and a 4A fuse for 24V.\n\u003c\/p\u003e\n\u003ch3\u003eControl and integration options\u003c\/h3\u003e\n\u003cp\u003e\n    The LUX SL driver offers flexible control options. It can operate autonomously with momentary switches for on\/off control, dimming, and color selection (cool white, neutral white, warm white, or RGB depending on the model). For advanced management, it integrates with the Lumishore EOS-LUX control center. This integration enables full control of CRGBW colors (cool white, red, green, blue, warm white), white temperature adjustment (from 2700 K to 6500 K), and advanced lighting effects via compatible multifunction displays (MFD), dedicated Lumishore screens, or smart devices. Each LUX module can also be controlled locally using switches mounted in the dashboard, providing independent control when needed.\n\u003c\/p\u003e\n\u003ch3\u003eRobust design for marine environments\u003c\/h3\u003e\n\u003cp\u003e\n    With its fully encapsulated and sealed (potted) construction, the LUX SL driver has an IP68 rating, providing high protection against dust and water immersion. This makes it suitable for harsh marine conditions. The electrical installation is plug-and-play, though mounting on a flat, cool, dry, and well-ventilated surface is recommended to optimize performance and lifespan. The product is covered by a three-year warranty.\n\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":56008702198100,"sku":"010-04438-00","price":136.5,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/01_47ce56fc-7f2b-49c1-a0ef-99f528abc314.jpg?v=1780432527"},{"product_id":"lumishore-lux-light-control-module-eclairage-marin","title":"LUX, lighting control module","description":"\u003cp\u003e\n    Designed for centralized and flexible management of marine lighting, the Lumishore LUX lighting control module (010-04442-00) is a key component for Lumishore LUX lighting systems. This module can control up to 16 Lumishore lights, including downlights and courtesy lights, providing an integrated solution for vessels equipped with these lights. Use with other lighting brands is not supported and will void the warranty.\n\u003c\/p\u003e\n\u003ch3\u003eTechnical specifications and control flexibility\u003c\/h3\u003e\n\u003cp\u003e\n    The Lumishore LUX control module operates on a 10.5 to 31-volt power supply, with identical output voltage, ensuring compatibility with 12V and 24V systems. The typical maximum current for 16 lights is 9.6 amperes at 12V and 4.8 amperes at 24V. Each module must be individually protected by a fuse or circuit breaker suitable for the total current of the connected lights. The module has an IP68 rating, ensuring resistance to marine environments.\n\u003c\/p\u003e\n\u003cp\u003e\n    This module offers dual control options. It can be used standalone with momentary switches, providing on\/off functions, dimming via press-and-hold, and color selection (cool\/neutral\/warm white, and optionally red\/blue\/green\/magenta\/cyan). For deeper integration, it connects to a Lumishore EOS-LUX command center, enabling control via a compatible multifunction display (MFD), a dedicated EOS-LUX screen, or a smart device. This flexibility allows for localized management or full integration into the onboard network.\n\u003c\/p\u003e\n\u003ch3\u003eInstallation and strategic positioning\u003c\/h3\u003e\n\u003cp\u003e\n    Installation of the Lumishore LUX control module is recommended on a flat surface, in a cool, dry, and well-ventilated environment. Electrical and mechanical installation should be entrusted to a qualified professional. Connections to the lights are made via standard 3-conductor cable, with careful attention to wire gauge to avoid voltage drops, adhering to ABYC recommendations (no more than 3% drop at 12V, 10% at 24V). The module and lights come with 25 cm of unterminated cable, allowing for custom extensions.\n\u003c\/p\u003e\n\u003cp\u003e\n    Unlike simpler lighting solutions managed by basic switches, the Lumishore LUX module acts as an intelligent hub for Lumishore LUX systems, offering advanced control capabilities (dimming, color management) and network integration. While brands like Raymarine or B\u0026G offer their own ecosystems, this module is specifically designed for integrating Lumishore lights, ensuring compatibility and optimized performance within this environment. It is essential to unlock the full features of Lumishore LUX lights.","brand":"Garmin","offers":[{"title":"Default Title","offer_id":56008707047764,"sku":"010-04442-00","price":197.06,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/01_acb7982b-1695-483e-bf86-02315090e991.jpg?v=1780432901"},{"product_id":"garmin-supra-smx-i-connect-kit-installation-eclairage-marin","title":"SUPRA SMX i-Connect Install Kit, i-Connect Install Kit with Switch and Hub Connect","description":"\u003cp\u003e\n    Designed to simplify the integration of underwater lighting systems, the \u003cstrong\u003eGARMIN SUPRA SMX i-Connect installation kit\u003c\/strong\u003e (part number 010-04443-00) is a plug-and-play solution dedicated to Lumishore underwater lights in the SMX, THX, and TIX series. This kit enables centralized control and reliable power supply for up to four lights per hub, with the ability to expand up to four hubs for SMX systems and sixteen hubs for THX and TIX systems.\n\u003c\/p\u003e\n\n\u003ch3\u003eIntegration and technical performance\u003c\/h3\u003e\n\u003cp\u003e\n    This kit operates within a voltage range of 10.5 to 31 VDC (nominal 12 V\/24 V DC) and draws a maximum of 0.2 A at 12 V. It supports a maximum input current of 40 A and an output current of 10 A per light. The hub, measuring 148 mm x 79 mm x 38 mm, is housed in a robust weather-resistant ABS enclosure and features IP68 protection for the hub and connectors, ensuring durability in marine environments. The manufacturer’s warranty is 3 years.\n\u003c\/p\u003e\n\n\u003ch3\u003eAdvanced control features\u003c\/h3\u003e\n\u003cp\u003e\n    The \u003cstrong\u003eGARMIN SUPRA SMX i-Connect installation kit\u003c\/strong\u003e includes a hub and a SUPRA i-Connect switch, four field-installable connectors, and a fuse kit. Light control is possible via the supplied switch, OneHelm™-certified Garmin multifunction displays (MFD) with an optional SUPRA Bridge module, or an EOS-LUX-SUPRA display. The switch allows toggling between color, strobe, and fade modes. For safety and reliability, the system integrates a switching relay, replaceable blade fuses for each light, status LEDs, a noise filter, and reverse polarity protection.\n\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":56008707113300,"sku":"010-04443-00","price":175.08,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/01_9540f1c9-25ce-4eea-8c97-9329c22b934c.jpg?v=1780432980"},{"product_id":"lumishore-lux-rs232-trigger-module-eclairage","title":"LUX RS232 Trigger Module","description":"\u003cp\u003e\n    Designed to extend the control capabilities of Lumishore EOS-LUX marine lighting systems, the \u003cstrong\u003eGarmin LUX RS232 Trigger Module (010-04446-00)\u003c\/strong\u003e enables activation of preconfigured \"scenes\" in the Lumi-Link Command Center. This module provides advanced integration, allowing light events to be triggered from external control systems independently of the multifunction display (MFD) or smart device power state.\n\u003c\/p\u003e\n\n\u003ch3\u003eIntegration and control flexibility\u003c\/h3\u003e\n\u003cp\u003e\n    This trigger module stands out for its versatility. It supports up to four momentary switches to activate specific scenes by applying a voltage of +3 to +24 volts to the corresponding trigger wires. For more complex setups, it supports up to fifteen triggers via a digital switch using a binary format across four wires (yellow, blue, green, white). Compared to a simple direct switch connection, this module multiplies control options and enables more nuanced management of lighting ambiances.\n\u003c\/p\u003e\n\n\u003ch3\u003eAdvanced RS232 connectivity\u003c\/h3\u003e\n\u003cp\u003e\n    Beyond physical triggers, the 010-04446-00 module includes an RS232 interface, offering a solution for systems requiring programmable automation. Communication operates at a baud rate of 38400, 8 data bits with no parity, and 2 stop bits. Commands are sent in the format \"T\" followed by the trigger number (e.g., T12 for trigger 12). This feature is essential for installations requiring precise synchronization and automated lighting sequences, positioning this module as a key component for sophisticated marine lighting systems. It is compatible with Lumishore EOS-LUX systems, operating on 12 or 24-volt networks and supporting up to 32 lighting zones with CRGBW control.\n\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":56008707801428,"sku":"010-04446-00","price":107.75,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/01_c940ff86-85f4-4361-a386-3d04a0641a5e.jpg?v=1780432997"},{"product_id":"lumishore-lux-light-control-module-din-rail","title":"LUX, lighting control module for DIN rail","description":"\u003cp\u003e\n    The Lumishore LUX DIN Rail lighting control module (reference 010-04451-00) is specifically designed for centralized management of Lumishore LUX lighting systems aboard vessels. It allows control of up to 16 Lumishore LUX lights, including downlights and courtesy lights. This module integrates into an existing electrical system with an input and output voltage range of 10.5 to 31 volts, ensuring compatibility with 12V and 24V marine installations.\n\u003c\/p\u003e\n\u003ch3\u003eInstallation and control flexibility\u003c\/h3\u003e\n\u003cp\u003e\n    Designed for DIN rail mounting, the Lumishore LUX module provides neat and professional installation within the vessel’s electrical panel. Each module must be individually protected by a suitable fuse or circuit breaker, sized according to the total consumption of connected lights. Light wiring is done via standard 3-core cable, in \"daisy chain\" or star configuration, with careful attention to cable cross-section to comply with ABYC recommendations (3% voltage drop at 12V and 10% at 24V).\n\u003c\/p\u003e\n\u003cp\u003e\n    This module stands out for its versatile control options. It can operate autonomously, controlled by standard momentary switches, offering on\/off functions, dimming, and selection of predefined white colors (cool, neutral, warm) or RGB. Alternatively, it integrates with the Lumishore EOS-LUX Command Center, enabling advanced control via a multifunction display (MFD), the dedicated EOS-LUX screen, or a smart device. This DMX integration ensures comprehensive vessel lighting management while retaining local control via switches for specific zones.\n\u003c\/p\u003e\n\u003ch3\u003eCompatibility and positioning\u003c\/h3\u003e\n\u003cp\u003e\n    The Lumishore LUX DIN Rail module is exclusively compatible with Lumishore LUX lighting products. This module is a dedicated solution for the Lumishore LUX ecosystem. This specialization ensures optimized performance and full software integration within Lumishore systems. Use with other lighting brands or non-LUX Lumishore products voids the warranty. Its DIN rail design positions it as a preferred solution for new installations or refits requiring clean and centralized electrical integration.\n\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":56008709013844,"sku":"010-04451-00","price":235.6,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/01_daf950dc-5a76-4ca4-a090-79314f206e76.jpg?v=1780433067"},{"product_id":"lumishore-lux-strip-light-driver-din-rail-eclairage-marin","title":"LUX, LED strip driver on DIN rail","description":"\u003cp\u003e\n    Designed by Lumishore, the LUX Strip Light Driver - DIN Rail is a dedicated solution for managing and controlling Lumishore LUX LED strip and flexible neon lighting. This module includes a voltage stabilizer, providing a regulated and stable 24-volt power supply to the fixtures, which enhances the reliability of the lighting system and protects it from voltage fluctuations on board. Its marine-grade powder-coated aluminum housing and IP68 waterproof rating ensure resistance to demanding marine environments.\n\u003c\/p\u003e\n\n\u003ch3\u003eIntegration and control flexibility\u003c\/h3\u003e\n\u003cp\u003e\n    The LUX Strip Light Driver serves as a central component for Lumishore LUX lighting installations. It offers full CRGBW color control and precise white tuning, enabling customization of the onboard lighting ambiance. This driver can operate autonomously, controlled by a simple momentary switch for on\/off and dimming functions. Alternatively, it integrates with the Lumishore EOS-LUX Command Center lighting system, providing advanced features and centralized control via a compatible multifunction display (MFD) or smart device. This dual approach accommodates various installation setups, from the simplest to the most complex.\n\u003c\/p\u003e\n\n\u003ch3\u003eTechnical specifications and installation\u003c\/h3\u003e\n\u003cp\u003e\n    This driver is powered by 12 V or 24 V input, with an operating range of 10.5 to 31 VDC, but always delivers a stabilized 24 V output. Its current draw is 0.05 A (max) at 12 V and 0.03 A (max) at 24 V, with an average power consumption of 0.6 W for the unit alone. It supports a maximum power output of 68 watts and can handle up to 10 meters of LED strip (comprising two 5-meter sections). Each driver must be individually protected by a 7.5 A fuse for 12 V input or a 4 A fuse for 24 V input. Its compact dimensions of 113 mm (width) x 27 mm (depth) x 77 mm (height) facilitate installation on a DIN rail or flat surface in a cool, dry, and well-ventilated location. Electrical installation can be either \"plug and play\" or hardwired, but must be performed by a qualified professional to ensure compliance and maintain the three-year warranty.\n\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":56008709079380,"sku":"010-04453-00","price":183.06,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/01_1142756d-a8bd-4f8c-9e76-ae9613393844.jpg?v=1780433083"},{"product_id":"garmin-eclipse-command-center-controleur-eclairage-marin","title":"ECLIPSE, control center","description":"\u003cp\u003e\n    Designed for centralized control of marine lighting systems, the Garmin (Lumishore) \u003cstrong\u003eECLIPSE Command Center\u003c\/strong\u003e is a versatile control solution. This unit integrates LED drivers for extended compatibility with various ECLIPSE light types, including downlights, courtesy lights, LED strips, Neon Flex, spotlights, and underwater lights, eliminating the need for additional modules. It is specifically designed for 12 V vessels, operating within a 10 to 15 V DC range.\n\u003c\/p\u003e\n\n\u003ch3\u003eIntegration and flexible control\u003c\/h3\u003e\n\u003cp\u003e\n    The ECLIPSE Command Center offers flexible connectivity. It features built-in Wi-Fi for direct control via a smart device (smartphone\/tablet) and can also integrate with an MFD (multifunction display) network via Ethernet. This multibrand capability allows connection to Garmin, Raymarine, Simrad, B\u0026G, and Furuno MFDs, although specific conversion cables (Garmin PN: 60-0372, Raymarine PN: A80151, Navico PN: 60-0373) are required for some brands. It provides 3 configurable lighting zones, expandable to 6 zones with optional expansion modules, each supporting a maximum load of 10 amperes for a total load of 30 amperes.\n\u003c\/p\u003e\n\n\u003ch3\u003eAdvanced features and maintenance\u003c\/h3\u003e\n\u003cp\u003e\n    The user interface allows creation and storage of customized lighting \"scenes,\" adjustment of colors and effects, and configuration of each zone based on the connected light type. A \"Sound to Light\" function is also available for RGBW underwater lights via a 3.5 mm jack input. For maintenance, the unit includes an SD card slot for software updates (minimum 4 GB SD card, class 10 recommended). The system supports OTA (Over The Air) updates via a PC\/laptop without losing configuration. However, SD card updates will erase all user settings and configuration data. The unit is rated IP67, ensuring protection against dust and temporary immersion, and comes with a 3-year warranty.\n\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":56008725430612,"sku":"010-04486-00","price":459.35,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/01_23f90160-7ef2-43a6-b105-b0426c7b8d22.jpg?v=1780433634"},{"product_id":"garmin-module-extension-eclipse-1-zone-eclairage-marin","title":"ECLIPSE, 1-zone extension module","description":"\u003cp\u003e\n    Designed to extend the capabilities of an existing Garmin ECLIPSE marine lighting system, the ECLIPSE 1-zone extension module from Lumishore adds an independent lighting zone. This module increases the system’s total capacity to up to six distinct lighting zones when paired with an ECLIPSE control hub.\n\u003c\/p\u003e\n\u003ch3\u003eIntegration and Compatibility\u003c\/h3\u003e\n\u003cp\u003e\n    The ECLIPSE extension module integrates with the ECLIPSE control hub, which can be controlled via Wi-Fi from a smart device (phone\/tablet) or via a compatible multifunction display (MFD). It supports Ethernet connectivity to Garmin MFD networks, Raymarine (via Raynet to RJ45 A80151 cable), Simrad\/B\u0026G (via Navico 60-0373 conversion cable), and Furuno (via standard CAT5e Ethernet cable). This multi-platform compatibility ensures flexibility for integration in various marine environments. Unlike the main control hub, which manages the initial zones, this module focuses solely on adding one additional zone, enabling system modularity.\n\u003c\/p\u003e\n\u003ch3\u003eTechnical Specifications and Features\u003c\/h3\u003e\n\u003cp\u003e\n    Operating at 12 V (range 10 to 15 VDC) with a maximum current draw of 0.04 A (module alone) and average power consumption of \u0026lt;0.5 W, this module is designed for energy efficiency. Its construction in robust, flame-retardant, halogen-free ABS with an IP67 rating provides resistance to dust and temporary immersion up to 1 meter for 30 minutes. Each added lighting zone includes dimming, color selection, and strobe functions. The \"Sound to Light\" feature is specifically supported for RGBW lights. Control can be achieved via a momentary switch input or through the ECLIPSE control hub interface. The module is compatible with all Lumishore ECLIPSE lights, whether submerged or above water.\n\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":56008725692756,"sku":"010-04487-00","price":143.67,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/01_c486077a-e24b-48c7-b1f4-da4d16badadf.jpg?v=1780433655"},{"product_id":"lumishore-eclipse-module-extension-2-zones","title":"ECLIPSE, 2-zone extension module","description":"\u003cp\u003e\n    Designed to extend the lighting capabilities of marine systems, the Garmin ECLIPSE 2-zone extension module is a key component for ECLIPSE lighting installations. It adds two independent lighting zones to the existing system, increasing the three built-in zones of the ECLIPSE Command Center to a total of six manageable zones. This module operates exclusively with the ECLIPSE Command Center, complementing its features for broader onboard lighting control.\n\u003c\/p\u003e\n\n\u003ch3\u003eIntegration and Performance\u003c\/h3\u003e\n\u003cp\u003e\n    This extension module operates on a 12 V DC power supply, with an operating range of 10 to 15 V DC. Each added zone is independently controllable, offering customization options for light intensity, color selection, and strobe effects. The maximum load capacity per zone is 10 amperes. The unit features a robust, flame-retardant, halogen-free ABS construction and is rated IP67 for protection against dust and water immersion.\n\u003c\/p\u003e\n\n\u003ch3\u003eControl and Compatibility\u003c\/h3\u003e\n\u003cp\u003e\n    Lighting zones are controlled via multiple interfaces, including momentary switches, Wi-Fi connectivity through a compatible smart device (smartphone or tablet), and integration with compatible multifunction displays (MFD). The system supports a variety of ECLIPSE lighting products, including ceiling lights, courtesy lights, light strips, flexible neon, spotlights, and underwater lights. The \"sound to light\" function is available for RGBW underwater lights when connected to the Command Center. Compared to an ECLIPSE Command Center alone, this module significantly expands lighting coverage and ambiance scenarios for larger vessels or complex configurations.\n\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":56008725922132,"sku":"010-04488-00","price":188.27,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/01_57e70e43-4af4-4fa7-ba81-78e9587f431b.jpg?v=1780433678"},{"product_id":"garmin-lux-smx154-set-eclairage-sous-marin-connecte","title":"LUX SMX154 Kit, 2 underwater lights, LUX hub and control center","description":"\u003cp\u003e\n    Designed for vessels requiring high-performance underwater lighting and advanced system integration, the Garmin LUX SMX154 set combines powerful lights with an intelligent control center. This kit includes two SMX154 underwater lights, an EOS hub, and an EOS-LUX Command Center, providing a complete solution for onboard lighting management.\n\u003c\/p\u003e\n\u003ch3\u003eHigh-performance underwater lighting\u003c\/h3\u003e\n\u003cp\u003e\n    Each SMX154 light is a surface-mount model delivering 7,000 verified lumens per fixture, for a total of 14,000 lumens. These lights feature a full EOS RGBW LED array with 16 x 3 W red LEDs, 12 x 3 W green LEDs, 12 x 3 W blue LEDs, and 12 x 10 W white LEDs. They provide a wide 90° beam angle and are built with a marine-grade bronze body and borosilicate glass lens, ensuring resistance to marine environments with IP68 certification. Their typical lifespan exceeds 50,000 hours.\n\u003c\/p\u003e\n\u003ch3\u003eAdvanced control and MFD integration\u003c\/h3\u003e\n\u003cp\u003e\n    The system’s core is the EOS-LUX Command Center (part number 60-0366), IP67 certified. It enables full RGB spectrum control and adjustable white color temperature from 2700K to 6500K. It supports fully configurable zone control, custom lighting scenes, and Lumi-Link capability for direct integration with certified multifunction displays (MFD). The Command Center is compatible with Garmin MFDs (OneHelm), Raymarine (Axiom with Lighthouse app), Navico (Simrad NSO EVO3\/EVO2, NSS EVO3\/Go, B\u0026G Zeus3\/Vulcan), and Furuno (Navnet TZ Touch 3). It also supports Wi-Fi control via a connected device or the MFD’s Wi-Fi network. Powered between 10.5 and 31 V DC, it draws a maximum of 0.5 A and includes reverse polarity and overload protection (Load Dump Protection), as well as ignition protection (ISO 8846). Its robust ABS construction, weather-resistant (flame-retardant and halogen-free), ensures reliability.\n\u003c\/p\u003e\n\u003ch3\u003eInstallation and features\u003c\/h3\u003e\n\u003cp\u003e\n    The Garmin LUX SMX154 system is designed for simplified installation with plug-and-play connections and a unique light discovery and auto-installation function. The system supports over-the-air (OTA) software updates and allows backup and restoration of settings. It offers features such as color selection, color cycles (Spectrum, Ice, Sunset, Miami), color sweeps, fixed or pulsed strobe, brightness adjustment, and diagnostics. A notable feature is \"Sound to Light\" compatibility, enabling lighting synchronization with music. The kit is covered by a 3-year warranty for the lights and 2 years for the Command Center.\n\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":56008729919828,"sku":"010-04510-00","price":2552.49,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/01_ac95415b-e7c6-4798-a7de-709f41b84ce8.jpg?v=1780433995"},{"product_id":"garmin-lux-smx154-set-eclairage-sous-marin","title":"LUX SMX154 Kit, 2 underwater lights, hub, LUX control unit and display","description":"\u003cp\u003e\n    The Garmin LUX SMX154 set is a complete underwater marine lighting solution designed for vessels requiring versatile and integrated illumination. The system includes two SMX154 underwater lights, an EOS hub, an EOS-LUX control unit (Lumi-Link), and a dedicated Lumishore display, providing centralized control and advanced lighting options.\n\u003c\/p\u003e\n\n\u003ch3\u003eSMX154 Underwater Lights: Performance and Durability\u003c\/h3\u003e\n\u003cp\u003e\n    Each SMX154 underwater light features 16 red 3 W LEDs, 12 green 3 W LEDs, 12 blue 3 W LEDs, and 12 white 10 W LEDs, delivering 7,000 lumens with a 90° beam angle. This configuration provides wide and powerful illumination. The lights offer full RGB color options with white (6500K), as well as single and dual-color modes. Constructed from marine bronze with a borosilicate glass lens and IP68 rating, they are resistant to marine environments. Installation is surface-mounted using three included marine bronze screws. Operation is compatible with 12 V\/24 V DC power, with a maximum consumption of 4 A per light at 12 V and 2 A at 24 V.\n\u003c\/p\u003e\n\n\u003ch3\u003eLumi-Link Control Unit: Integration and Flexibility\u003c\/h3\u003e\n\u003cp\u003e\n    The system’s core, the Lumi-Link control unit (part number 60-0366), is IP67-rated and operates on a 10.5 to 31 V DC supply, with a maximum consumption of 0.2 A at 12 V and 0.1 A at 24 V. It enables full RGB spectrum control and adjustable white color temperature (2700K to 6500K). It includes fully configurable zone control, customizable lighting scenes, and Lumi-Link compatibility for control via certified MFD or the included Lumi-Link display. It supports Garmin (OneHelm), Raymarine (Axiom), Navico (Simrad NSO EVO3\/EVO2, NSS EVO3\/Go, B\u0026G Zeus3\/Vulcan), and Furuno (Navnet TZ Touch 3) MFDs. Control is also possible via Wi-Fi from a connected device. Installation is simplified with plug-and-play connections and over-the-air software updates.\n\u003c\/p\u003e\n\n\u003ch3\u003eSystem Architecture and Features\u003c\/h3\u003e\n\u003cp\u003e\n    This set includes an EOS hub (IP68) and a dedicated Lumishore display (IP68), contributing to the system’s robustness and ease of use. Average total power consumption is 103 W. The system is protected against reverse polarity and load dump surges, and is certified to ISO 8846 for ignition protection. It supports features such as light synchronization, color cycling (Spectrum, Ice, Sunset, Miami), color sweep, fixed or strobe modes, and the \"Sound to Light\" function. The system allows light discovery and configuration, brightness adjustment, and diagnostics. The kit is backed by a 3-year warranty, ensuring a reliable underwater lighting solution. The system can be expanded by connecting up to four hubs and using Lumishore extension cables for lights and power.","brand":"Garmin","offers":[{"title":"Default Title","offer_id":56008730542420,"sku":"010-04511-00","price":2999.78,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/01_ac7cc8ba-6405-4f1a-b750-79938cce9107.jpg?v=1780434014"},{"product_id":"lumishore-supra-thx404-eclairage-sous-marin-double-couleur-thru-hull","title":"SUPRA THX404, thru-hull underwater light with driver","description":"\u003cp\u003e\n    Designed for demanding vessels such as sports boats, cruisers, yachts, and superyachts, the \u003cstrong\u003eLumishore SUPRA THX404\u003c\/strong\u003e underwater lighting system provides an integrated thru-hull solution. It targets owners seeking the integrity of a thru-hull installation combined with powerful and efficient LED underwater technology. Within the Lumishore SUPRA range, the THX404 is positioned as a mid-power solution for thru-hull installations, offering a balance between light intensity and compactness compared to the more powerful THX804 and THX1604 models.\n\u003c\/p\u003e\n\n\u003ch3\u003eLight performance and versatility\u003c\/h3\u003e\n\u003cp\u003e\n    The \u003cstrong\u003eSUPRA THX404\u003c\/strong\u003e integrates a set of 12 x 10 W LEDs for white lighting (6500K) and 24 x 3 W LEDs for blue lighting, delivering a light output of 8 150 lumens in white mode. Its optics provide an ultra-wide 110° beam angle, creating a distinctive \"halo effect\" for extended water illumination. The system allows independent color control, brightness adjustments, as well as strobe and fade modes, all synchronizable for a coherent lighting experience. The typical LED lifespan exceeds 50 000 hours.\n\u003c\/p\u003e\n\n\u003ch3\u003eRobust design and system integration\u003c\/h3\u003e\n\u003cp\u003e\n    The \u003cstrong\u003eTHX404\u003c\/strong\u003e construction features a marine-grade bronze (or marine-grade aluminum bronze) body and a borosilicate glass lens, ensuring high resistance to marine environments. IP68 certified, this underwater light is fully water- and dustproof. It operates within a voltage range of 10.5 to 31 VDC (12 V\/24 V DC), with a maximum current draw of 6.4 A at 12 V or 3.2 A at 24 V, for an average power of 77 W. The installation is thru-hull, with a flush design and a compact external electronic driver for operational reliability. Control can be via the SUPRA i-Connect Hub \u0026 Switch or directly from a compatible multifunction display (MFD), in conjunction with the optional Lumishore SUPRA Bridge module.\n\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":56008735752532,"sku":"010-04516-00","price":1103.21,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/01_16dadd98-427a-46c4-a93c-7c1d3f36997b.jpg?v=1780434070"},{"product_id":"lumishore-supra-thx804-eclairage-sous-marin-led-double-couleur","title":"SUPRA THX804, through-hull underwater light with driver","description":"\u003cp\u003e\n    The LUMISHORE SUPRA THX804 underwater LED lighting is a high-intensity through-hull illumination solution designed for sportboats, cruisers, yachts, and superyachts. Featuring advanced Lumishore technology, this system integrates a light module and a compact external electronic driver for reliable performance and extended service life.\n\u003c\/p\u003e\n\n\u003ch3\u003ePerformance and Technical Specifications\u003c\/h3\u003e\n\u003cp\u003e\n    The SUPRA THX804 delivers powerful illumination with a total of 30,375 lumens, including 13,500 verified lumens in white mode. It uses a HICOB Array LED configuration, comprising 36 x 10W LEDs for white and 48 x 3W LEDs for blue, offering dual-color capability. Its 110-degree ultra-wide beam ensures broad coverage and underwater halo effects. With a typical lifespan exceeding 50,000 hours, this lighting system is built for longevity. It operates on a 12V\/24V DC power supply, with an operating range of 10.5–31 VDC, and a maximum current draw of 8.8A (at 12V) or 4.4A (at 24V), for an average power consumption of 106 W.\n\u003c\/p\u003e\n\n\u003ch3\u003eDesign and Integrated Control\u003c\/h3\u003e\n\u003cp\u003e\n    The LUMISHORE SUPRA THX804 is engineered for marine environments, featuring a marine-grade bronze (also listed as marine aluminum bronze) housing and a glass lens, ensuring IP68 water and dust resistance. Its flush-mounted, low-profile design allows seamless integration into the hull. The system offers dynamic lighting effects, including color variation, brightness adjustment, and dual-speed strobe modes. Control is versatile, operating via the SUPRA i-Connect Hub \u0026 Switch, compatible MFDs with the optional SUPRA Bridge module, or even via Wi-Fi using the SUPRA Bridge module. This multi-light synchronization capability enhances the visual experience. Compared to basic underwater lighting solutions, the THX804 stands out as a complete system offering superior control flexibility and light output, competing with premium offerings from specialized marine lighting brands thanks to Lumishore technology.\n\u003c\/p\u003e\n\n\u003ch3\u003eInstallation and Reliability\u003c\/h3\u003e\n\u003cp\u003e\n    The through-hull installation of the LUMISHORE SUPRA THX804 is designed for robust and permanent integration. It must be mounted on a flat surface (transom or hull side) at a depth of 150–250 mm below the minimum waterline. For optimal results, a spacing of 0.8 to 2 meters between lights is recommended. For wooden, metal, or carbon fiber hulls, an isolation kit is required. Bolt torque must not exceed 3 Nm \/ 26 in-lbs. Each light comes with a 3m cable and preinstalled connector, while the external driver includes a 1m power cable, with extensions available. All Lumishore products are recommended for DC system bonding via a bonding strap for galvanic protection unless the light is fully immersed fore and aft. The 3-year warranty underscores the manufacturer’s confidence in product durability.\n\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":56008735981908,"sku":"010-04518-00","price":1810.34,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/01_6a6d9fa3-02de-4d0a-bc28-06e259b78086.jpg?v=1780434087"},{"product_id":"garmin-supra-thx1604-eclairage-sous-marin-traversant","title":"SUPRA THX1604, through-hull underwater light with driver","description":"\u003cp\u003e\n    The Garmin SUPRA THX1604 underwater lighting system is a high-power through-hull lighting solution designed for sport boats, motor yachts, sailboats, and superyachts. This model stands out with its high luminous flux and ultra-wide 110-degree beam, providing extended underwater illumination. With a total luminous flux of 45,000 lumens and up to 20,000 lumens at the fixture for white light, it outperforms lower-power models such as the THX404 or THX804 in the same Lumishore\/Garmin range, as well as many entry-level underwater lights.\n\u003c\/p\u003e\n\u003ch3\u003eAdvanced performance and features\u003c\/h3\u003e\n\u003cp\u003e\n    The SUPRA THX1604 integrates a set of HICOB Array LEDs, ensuring a typical lifespan of over 50,000 hours. This model, the SUPRA THX1604 (SKU 010-04519-00), is a dual-color blue\/white version delivering 20,000 lumens at the fixture. The THX1604 range is also available as an RGBW color option (17,500 lumens at the fixture), offering flexibility to match the vessel’s aesthetics. Maximum power draw is 6.5 A at 24 VDC, with an average power consumption of 156 W. The system is powered by a 24 VDC operating voltage (range 20–31 VDC).\n\u003c\/p\u003e\n\u003ch3\u003eIntegration and robustness\u003c\/h3\u003e\n\u003cp\u003e\n    The THX1604 design features a marine-grade bronze housing and a borosilicate glass lens, ensuring resistance to marine environments and an IP68 waterproof rating. The compact electronic driver module is external for operational reliability. The through-hull installation, with a low-profile and flush design, is intended for the transom or hull sides, using a standard 1-inch fitting. Control is versatile, via the SUPRA i-Connect Hub \u0026 Switch, compatible multifunction displays (MFD) with the SUPRA Bridge module, an optional Lumishore display, a momentary switch, or via WiFi from a smartphone or tablet. These extended control options position it favorably compared to competing solutions with less integration flexibility.\u003c\/p\u003e","brand":"Garmin","offers":[{"title":"Default Title","offer_id":56008736670036,"sku":"010-04519-00","price":2770.45,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/files\/01_5d287933-f99b-40b5-8ef3-b311806379d3.jpg?v=1780434105"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0988\/3274\/4788\/collections\/eb69b6ca10589f4708de0332a5a1722c.png?v=1779971486","url":"https:\/\/skysat.fr\/en-us\/collections\/lighting-controls.oembed","provider":"Skysat","version":"1.0","type":"link"}