Fusion Apollo ERX400 Marine Stereo Source

The Fusion Apollo ERX400 housing contains the following items:

A mounting gasketA mounting templateFour #8 self-tapping screwsTwo screw capsA dust coverA power/network cable

To install the Fusion Apollo ERX400 remote control, you will need the following tools:

A Phillips screwdriverAn electric drillA drill bit (size varies depending on the surface material and screws used)A rotary cutting tool or jigsawMarine-grade silicone sealant (optional)

The dimensions of the Fusion Apollo ERX400 marine stereo source are 11 cm in width by 7 cm in height (4.32 x 2.76 inches).

The dust cover measures 11.8 cm in width by 8 cm in height (4.66 x 3.15 inches).

The Fusion Apollo ERX400 has an IEC 60529 IPX6 and IPX7 water resistance rating. This means the unit can withstand accidental immersion in water up to 1 meter for a maximum of 30 minutes and is protected against powerful water jets.

The required input voltage range for the Fusion Apollo ERX400 is 10.8 to 32 Vdc with negative ground.

The Fusion Apollo ERX400 power consumption is as follows:

150 mA in normal operation at 12 Vdc125 mA in normal operation at 14.4 VdcLess than 50 mA when the unit is powered off

An ATO-type blade fuse rated 1 A is required for the Fusion Apollo ERX400 installation. Do not remove the supplied inline fuse holder, as this may void the product warranty and cause damage.

To avoid any interference with a magnetic compass, you must install the Fusion Apollo ERX400 remote control at least 15 cm (5.9 inches) away from it.

To mount the Fusion Apollo ERX400, follow these steps:

Cut out the provided template and attach it to the mounting surface. Drill a hole inside the corner of the dotted line on the template, then use a jigsaw or rotary cutting tool to cut along the inside of the solid line on the template. Ensure the mounting holes of the remote align with the pilot holes on the template. Drill the pilot holes with a drill bit of the appropriate size for the mounting surface and screw type. Remove the template. Place the provided mounting gasket on the back of the remote if the location is dry, or apply marine-grade silicone sealant around the cutout if the location is exposed to water (do not use both). If using the spacer accessory, install the gasket or sealant on the back of the spacer. Connect the network/power cable to the back of the remote and tighten the locking ring if you will not have access to the rear after installation. If using the spacer accessory, install the spacer and the gasket or sealant between the mounting surface and the remote. Secure the remote to the mounting surface using the included screws. Snap the screw covers into place.

Yes, the Fusion Apollo ERX400 can be installed in a water-exposed location thanks to its IPX6 and IPX7 water resistance rating. However, if you install it outside a boat, it must be mounted well above the waterline where it will not be submerged and cannot be damaged by docks, pilings, or other equipment.

When installing in a water-exposed location, it is recommended to apply marine-grade silicone sealant around the cutout on the mounting surface. Do not use the supplied mounting gasket if you are applying sealant, as this could reduce water resistance.

Yes, the Fusion Apollo ERX400 is compatible with Fusion PartyBus™ networks. It can connect to a single compatible stereo system (such as an MS-RA770) or to the Fusion PartyBus network to view and control all stereo systems connected to the network.

To connect the Fusion Apollo ERX400 to the power supply and network:

Route the power/network cable to the stereo system, switch, or network router. Connect the red power wire to the positive terminal (+) of the battery via a fuse or manual switch. Connect the black ground wire to the negative terminal (-) of the battery. Select an option: If using this device to control a single stereo system and have no other devices on a Fusion PartyBus network, connect the network connector to the ETHERNET port of the stereo system. If the boat has a network connecting multiple compatible devices, connect the network connector to an open port on the switch or network router. It is recommended not to connect the cable to the stereo system before connecting the power wires to avoid damage.

Yes, it is possible to extend the Fusion Apollo ERX400 cables:

Power and ground cables: If you need to extend them, use wires of the appropriate gauge. 18 AWG (0.82 mm²) wires are suitable for most installations. Network cable: Extension cables and couplers are available. Contact your Garmin dealer for details.

Yes, the Fusion Apollo ERX400 requires software updates. You must update the software of this unit using a compatible stereo system connected to it or via the Fusion-Link™ app. It is recommended to update the software of all FUSION devices after installing the ERX400 to ensure proper operation with all compatible stereo systems on the Fusion PartyBus network.

The temperature conditions for the Fusion Apollo ERX400 are as follows:

Operating temperature: From 0°C to 50°C (32°F to 122°F)Storage temperature: From -20°C to 70°C (-4°F to 158°F)

The weight of the Fusion Apollo ERX400 marine stereo source, without the cable, is 100 grams (3.5 oz).

When installing the Fusion Apollo ERX400, consider the following points:

Mount the remote control on a flat surface. If space behind the mounting surface is limited, use the MS-ERX400 (010-12922-02) spacer accessory. Add a drip loop to the cable near the stereo system if it is exposed to water to prevent damage. If the installation is outside the boat, mount the device well above the waterline where it will not be submerged or damaged. Install the remote control at least 15 cm (5.9 in) away from a magnetic compass to avoid interference.

Yes, a MS-ERX400 spacer accessory (part number 010-12922-02) is available. This spacer is useful if the space behind the mounting surface is limited or if you prefer to drill a smaller hole in the mounting surface.

Several actions can void the warranty of your Fusion Apollo ERX400:

Using the remote control as a template when drilling mounting holes, as this can damage it. Applying grease or lubricant to the screws when attaching the remote control to the mounting surface, as this can damage the housing. Removing the provided inline fuse holder when connecting to power.

For a flush-mounted installation of the Fusion Apollo ERX400, the mounting template indicates a cutout of approximately 44 mm (1 3/4 inches) in diameter if you use the spacer accessory. For a flush mount without the spacer, cut along the solid line of the template, which corresponds to a rounded rectangular shape.

It is strongly recommended to use the mounting template provided in the product box to ensure precise cutting.