Marine audio remote RGB

The box for the Fusion RGB marine audio remote control (010-12850-00) contains the following items:

RGB LED wireless remote controlA remote control receiverRemote control mount7.5 A inline fuseImportant safety and product information document

The Fusion RGB remote control allows you to control the LED lighting of your marine speakers. Its main functions include:

Turning LED lights on and offChanging color via a color wheel or direct white selectionAdjusting LED brightnessSelecting from 12 predefined display modes (blinking, breathing, color-changing effects)Adjusting the speed of display mode patterns

No, neither the remote receiver nor the remote itself is water- or dust-resistant. They must be installed in a protected location to prevent damage.

The remote control uses two AAA alkaline batteries. These batteries are not included and must be purchased separately.

The maximum range of the wireless remote control is approximately 10 metres (30 feet).

The remote control and its receiver can operate at temperatures ranging from 0 to 50°C (32 to 122°F). For storage, acceptable temperatures are -20 to 70°C (-4 to 158°F).

The remote offers 12 different LED display modes, including:

RGB color jumps or fadesSkipped changes, flashing, fading, or gradients of 7 colorsSpecific white, red, green, or blue modes with fades and flashesAn automatic mode that cycles through the previous 11 modes

To change the LED color, you can touch the color wheel on the remote control and slide your finger to fine-tune the color. To get white light, hold down the dedicated button for this purpose on the remote control.

The receiver housing is not waterproof, so it must be installed in a location protected from external elements such as water, moisture, or dust.

For installation, you will need the following cables (not included):

A 2-conductor 22 AWG (0.33 mm²) wire to connect the receiver to a 12 V DC power source. A 4-conductor 22 AWG (0.33 mm²) wire or an equivalent combination of 2-conductor wires to connect the receiver to the RGB LED displays.

Yes, it is crucial to disconnect the boat's electrical power before starting installation of this product. This ensures your safety and prevents any risk of damage to the vessel's electrical system.

Tools required for installation include:

A 3 mm flathead screwdriverWire cuttersIf you choose to install the remote mount (optional): a drill and drill bits

To connect the receiver to the 12 V DC power supply:

Run a power wire (not included) from a 12 V DC source to the receiver location.Install the 7.5 A fuse (included) on this power wire.Connect the V+ and V- terminals on the left side of the receiver to the positive (+) and negative (-) wires of the 12 V DC source, respectively.

The remote control mount is provided to store the remote. To install it:

Use the mount as a template to mark the positions of the two pilot holes.Drill the pilot holes at the marked positions.Attach the mount to the mounting surface using two 4-gauge (3 mm) stainless steel countersunk screws, which are not included.It is important to install the mount in a location not exposed to the elements, as the remote is not waterproof.

During installation, it is recommended to:

Always wear safety glasses, hearing protection, and a dust mask when drilling, cutting, or sanding. Always check what is on the other side of the surface before drilling or cutting to avoid damaging the boat.

You can connect up to 8 RGB LED speakers, which corresponds to 4 pairs of speakers, to a single remote receiver.

Yes, a single remote can be paired with a maximum of three receivers. This allows you to control up to three separate groups of RGB LED lights with the same remote.

This remote is specifically designed to control RGB LED lighting for compatible Fusion marine speakers.

To pair an additional receiver with your remote:

Unplug then reconnect the power supply of the receiver you wish to pair.Within 6 seconds of power reconnection, press and hold for at least 2 seconds the group number (1, 2, or 3) you want to assign to this receiver on the remote.The LED in the center of the color wheel on the remote will flash 3 times to indicate successful pairing.Release the group number to finalize the pairing.