Marine subwoofer XS Sport edition 10", 600 W

This Fusion XS Sports edition 10-inch marine subwoofer has a power output of 600 W.

This Fusion XS marine subwoofer has a 10-inch diameter.

Yes, the front of the subwoofer is protected against water ingress. However, the rear of the subwoofer, including all components and connected wires, is not waterproof and must be protected from moisture. If the subwoofer is installed in an area exposed to weather or water, it must be mounted on a vertical surface to prevent water accumulation and potential damage.

The marine subwoofer Fusion XS package includes:

1 subwoofer6 Phillips stainless steel mounting screws, 4.8 mm x 50 mm (10 x 2 in)Mounting templateGrilles

Yes, this subwoofer is a Sports edition, meaning it comes with LED lighting.

For installing the subwoofer, you will need the following tools:

A power drillA drill bit (size varies depending on surface material)A Phillips screwdriverWire strippersMarine-grade tinned copper wire, 12 AWG (3 to 4 mm²) for standard speakersFemale spade connectors, 4.8 mm and 6.3 mm (recommended)Male and female 4 mm pin connectors (recommended)Crimping tool (optional)Electrical tapeA suitable saw or utility knife for cutting the surface materialMarine sealant (optional)

When choosing the mounting location, consider the following points:

The mounting surface must protect the rear of the subwoofer from moisture. It must provide sufficient clearance for the subwoofer’s mounting depth, as specified in the product specifications. A flat, vertical mounting surface is recommended for optimal sealing. The subwoofer’s wires must be protected from sharp objects by using rubber grommets when routing through panels.

It is recommended to use the template provided in the product box. If you must print the template, ensure the scaling is set to 100% before printing. After printing, use a ruler to measure at least one dimension line to verify that the template was printed at 100% scale.

The required cutout diameter for installing this subwoofer is Ø 223 mm (8 3/4 inches).

Use 12 AWG (3 to 4 mm²) fully tinned marine-grade copper speaker wire to connect the subwoofer to the amplifier or source.

The subwoofer wires must be connected with the following polarity:

The white wire corresponds to the positive (+). The grey wire with a black stripe corresponds to the negative (-). These wires are connected to jumper terminals at the rear of the subwoofer and must remain connected for normal use (4 Ohm). They should only be disconnected when configuring the speaker for 2.1 operation.

No, do not apply grease or lubricant to the screws when attaching the subwoofer to the mounting surface. Grease or other lubricants can damage the subwoofer's enclosure.

It is recommended to install an LED lighting controller module. If you choose not to use a controller, you can set a static color by connecting LED wire combinations directly to the power source. Available colors are:

Red: Red wireGreen: Green wireBlue: Blue wireYellow: Red and green wires combinedMagenta: Red and blue wires combinedCyan: Blue and green wires combinedWhite: Red, green, and blue wires combinedThe black wire of the LED cable is terminated with a 4 mm female pin connector, and the colored wires are terminated with 4 mm male pin connectors.

A 700 mA inline fast fuse must be installed on the positive wire at the power source end of the LED cable for each speaker. This fuse is essential to protect the LEDs and the speaker from excessive electrical current.

Yes, the subwoofer features a dual 2-ohm voice coil that can be configured for 2.1 operation (two speakers and one subwoofer) when connected to a Fusion stereo system with DSP (digital signal processing) capability.

For optimal connection, it is recommended to use female spade connectors (not included) to connect the speaker wire to the subwoofer wires. The subwoofer wires are terminated with male spade connectors.

It is recommended to install an LED lighting controller module to turn LED lights on and off, change colors, and create lighting effects. However, if you choose not to install a controller, you can set a static color for the LEDs by directly connecting LED wire combinations to the power source.

The limited warranty does not cover:

Cosmetic damage (scratches, scuffs, dents).
Consumables (unless the damage is due to a material or manufacturing defect).
Damage caused by an accident, misuse, abuse, water, flooding, fire, or other natural disasters or external causes.
Damage caused by service performed by a provider not authorized by Garmin.
Damage to a product modified or altered without Garmin’s written authorization.
Damage to a product connected to power and/or data cables not supplied by Garmin, or to power adapters and cables not UL-certified and not labeled as Limited Power Source (LPS).