FUSION Signature Series 3 Sport chromed 8.8" marine tower speakers, 330 W with CRGBW lighting

These Fusion Signature Series 3 marine tower speakers have a maximum power output of 330 W.

The tower speakers have an 8.8-inch diameter.

These speakers feature CRGBW lighting. This means they offer RGB colors (red, green, blue) as well as cool white and warm white, allowing a wide range of lighting options.

Yes, these speakers are True-Marine™ products. They undergo rigorous environmental testing under harsh marine conditions to exceed industry standards for marine products. When properly installed, they are rated IP65 for protection against dust and water ingress under normal conditions.

To clean your speakers:

Clean off any salt residue and saltwater with a damp cloth soaked in fresh water.Use a mild detergent to remove heavy salt buildup or stains.Warning: Do not use harsh or solvent-based cleaners, as they may damage the product and void the warranty.Also avoid high-pressure water jets, which are not designed for these speakers.

Yes, if the speakers are installed at an angle, you can rotate the speaker front and the end cap so the FUSION logo appears level.

For installation, you will need:

16 AWG (1.31 mm²) or 12 AWG (3.31 mm²) speaker cable
20 AWG (0.5 mm²) cable for LEDs
3 A inline fuse (for LEDs)
Speaker mounting bracket (sold separately)
Drill and 12 mm (1/2 in) bit
Wire strippers
Solder and dual-wall heat-shrink tubing for wire connections
Additional tools and materials may be required for custom installations.

No, mounting brackets for Fusion Wake tower speakers must be purchased separately. Different brackets are available for mounting on a wake tower bar or on a deck.

For most installations, a 16 AWG (1.31 mm²) speaker cable is recommended. However, the gauge may vary depending on the distance between the amplifier and the speaker, as well as the load (4 ohm or 2 ohm).

For a 4 ohm load (1 speaker): from 0 to 8.5 m (0 to 28 ft), use 16 AWG; from 8.5 to 21 m (28 to 69 ft), use 12 AWG. For a 2 ohm load (2 speakers in parallel): from 0 to 4 m (0 to 14 ft), use 16 AWG; from 4 to 10.5 m (14 to 35 ft), use 12 AWG. If using aluminum or tinned wire, it is advisable to use a gauge two sizes larger to compensate for potential voltage drop.

No, the speaker cable is not included with the speakers. You will need to use the recommended speaker cable to connect the speakers to your stereo system or amplifier.

Speaker wire polarity is as follows:

The white wire is positive (+). The white wire with a black stripe is negative (-). It is recommended to make all wiring connections using solder and heat-shrink tubing.

Use 20 AWG (0.5 mm²) or thicker wire to connect the LEDs to the battery.

Yes, you must connect the positive wire (+) of all the speaker LEDs to a 3 A inline fuse located near the power source. It is also advisable to connect the positive power wire (+) to the power source via an isolator switch or circuit breaker to turn the LEDs on and off.

It is recommended to install a FUSION CRGBW wireless remote (sold separately) to turn the LEDs on and off, change colors, and create lighting effects. If you choose not to install the remote, you can set a static color for the LEDs by connecting the colored LED wires directly to the negative terminal (-) of a 12 Vdc power source.

Yes, it is strongly recommended to have your audio system installed by a professional installer to ensure optimal performance.

If necessary, you will need to drill a 12 mm (1/2 in) cable pass-through hole in the tower or deck.

If you do not install the recommended remote control, you can set a static color by connecting the colored LED wires to the negative terminal (-) of a 12 Vdc power source. The black wire of the LED must be connected to the positive terminal (+) of the same power source. Here are some combinations:

Red: Red wire
Green: Green wire
Blue: Blue wire
Yellow: Red and green wires
Magenta: Red and blue wires
Cyan: Blue and green wires
Cold white: Turquoise wire
Warm white: Yellow wire
Unused LED wires must be insulated to prevent short circuits.

For full control of LED lighting, including on/off, color changes, and effects, it is recommended to install a FUSION CRGBW wireless remote. This remote is sold separately.

Yes, the speakers are designed to be connected to a marine stereo system or amplifier. The speaker wiring guide provides recommended wire gauge based on distance and load (4 Ohm or 2 Ohm) for optimal connection.

All True-Marine products from Fusion, including these speakers, are covered by a 3-year limited global consumer warranty.