Mastervolt Mass Sine 12/2000 Inverter - 230 V 60 Hz

The Mastervolt Mass Sine 12/2000 inverter (230V/60Hz) delivers continuous power of 1800W at an ambient temperature of 40°C, with a power factor of 1. It is designed to provide stable and reliable power for your equipment.

This inverter generates a pure sine wave. This ensures safe and optimal operation for all your equipment, including sensitive electronic devices that require high-quality power.

The Mastervolt Mass Sine 12/2000 inverter (230V/60Hz) has a conversion efficiency of 92%. This high efficiency optimizes the use of your battery's energy and reduces losses during DC to AC conversion.

The inverter integrates multiple protections to ensure the safety of the system and connected equipment. It is protected against:

OverheatingOverloadsShort circuitsHigh and low battery voltagesThese protections help extend the lifespan of the inverter and your battery bank.

This inverter is a 12/2000 model, meaning it is designed to operate with a battery system having a nominal voltage of 12 Volts DC.

The Mastervolt Mass Sine 12/2000 inverter (230V/60Hz) provides AC power with a frequency of 60 Hz (±0.01Hz). The output voltage is 230V (±5%).

Yes, the Mastervolt Mass Sine 12/2000 inverter (230V/60Hz) has a peak load capacity of up to 4000W. This capacity allows it to handle high inrush currents required to start demanding equipment, such as certain motors or compressors.

If the battery voltage drops too low, the Mass Sine 12/2000 inverter shuts down automatically to protect the battery from excessive discharge. For a 12V system, the cut-off voltage is 10V (±0.5V). The inverter restarts automatically when the battery voltage rises back above 11V (±0.5V).

The Mass Sine inverter overheating can be caused by several factors:

Heavy or non-resistive loads operating for an extended period.An elevated ambient temperature.Disrupted airflow (due to dust or insufficient installation space around the unit).It is critical to ensure adequate ventilation to prevent overheating.

Yes, the Mastervolt Mass Sine inverter has standby mode settings. You can configure low or high energy mode, enable or disable standby mode, and adjust its trigger power (0 to 40 watts) and hysteresis (0 to 100%).

The Mass Sine 12/2000 inverter (230V/60Hz) delivers a P30 power output of 2000W at an ambient temperature of 40°C, with a power factor of 1. The P30 power rating represents the power the device can supply continuously for 30 minutes.

The inverter is designed to operate within an ambient temperature range of 0°C to 60°C (32°F to 140°F). It is important to note that power reduction (derating) may occur above 25°C (104°F) to maintain the internal heat sink temperature at an optimal level.

The Mastervolt Mass Sine 12/2000 inverter (230V/60Hz) can operate in ambient humidity conditions ranging from 0 to 95%, without condensation.

The Mass Sine inverter is designed for indoor use only. It must be installed in an environment where the ambient temperature is between 0°C and 60°C and humidity between 0% and 95% without condensation. Ensure adequate airflow to prevent overheating.

For securing DC input cables (battery), it is recommended to use a 13 mm socket wrench as the minimum tool. It is also essential to use appropriate cable lugs crimped with a suitable crimping tool for wire ends.

For a safe installation, it is necessary to connect both the ground (PE/GND) and the neutral (N) of the inverter’s AC output to the system’s central grounding point. All wiring must comply with local codes and regulations.

It is crucial to keep DC cable lengths as short as possible to maximize system efficiency, as high currents will flow through them. For 12V models, a 2x 25mm² (AWG3) cross-section is recommended for cable lengths up to 2 meters (6 feet). Use properly crimped cable lugs.

For optimal and reliable operation, the Mastervolt Mass Sine 12/2000 inverter (230V/60Hz) is recommended for battery capacities greater than 200 Ah.

Several accessories are compatible for controlling and monitoring the Mass Sine inverter:

The Masterlink MICC panel (reference 70403105)
The Panel C-4-RI Remote control panel (reference 70404110)
The MasterBus Inverter Interface (reference 77030700)
The MasterBus AC power analyser (reference 77031200), which provides additional features such as precise status overview (voltage, current, load, frequency) and alarm functions.