Spectra™, Module de commande LED LC102

The Garmin Spectra LC102 LED control module is designed for centralized management of marine LED lighting. It allows control of LED lights using compatible Garmin chartplotters, compatible Fusion stereo systems, or the ActiveCaptain app.

The Spectra LC102 module supports RGB, RGBW, and CRGBW LED lighting. This includes marine speakers, subwoofers, and wake tower speakers from brands such as Fusion.

No, the Garmin Spectra LED control module is designed to control LED lighting only. It must not be used to control navigation lights, non-LED lighting, or other devices.

You can control LED lights connected to compatible Garmin chartplotters, compatible Fusion stereo systems (connected to the same NMEA 2000 network), or the ActiveCaptain app.

The module must be installed in a location where it will not be submerged. It is not designed to be immersed.

Yes, this device must be installed by a qualified marine installer. Specific knowledge of marine electrical systems is required for correct installation.

For installation, you will need the following tools and supplies:

16 AWG (1.3 mm²) wire to connect the cable harness to the power supply.
A properly rated inline fuse for the power source and connected LEDs.
20 AWG (0.5 mm²) wire to connect the cable harness to the lighting (a Garmin marine LED cable 010-13386-00 is available from your Garmin dealer).
No. 2 Phillips screwdriver.
Marine-grade connectors of appropriate size.
Wire cutters.
A drill and a 2 mm (3/32 in) bit for mounting the module.

When choosing the mounting location, consider the following points:

The device must be mounted in an accessible location. Avoid mounting it near fuel tanks or bilge areas where combustible vapors could accumulate. Choose a location with access to a common ground for other electronic devices. When controlling LED speakers, the controller must be mounted within 5 meters (16 feet 4 inches) of the speakers. The device must not be submerged. Mount the device on a flat, vertical mounting surface, with the cable harness connectors pointing downward. Clean the mounting surface of any dirt, debris, wax, or coating. Select a location away from sources that could interfere with the device’s operation, such as strong electromagnetic fields, power cables, and electric motors.

To mount the module:

With the cable harness connectors pointing downward, hold the device on a flat, vertical mounting surface and mark the pilot hole locations. Remove the device from the mounting surface. Using a 2 mm (3/32 in) drill bit, drill the pilot holes. Secure the included pan-head screws into the pilot holes. Attach the device to the mounting surface by tightening the screws until snug. Do not overtighten the screws, as this may damage the device housing. Do not use the module as a template when drilling mounting holes and do not apply grease or lubricant to the screws.

The power supply voltage of the LED control module must match the voltage of the LED lighting it controls (12 Vdc or 24 Vdc). The wiring from the power source to the positive wire of the power cable harness must pass through an inline circuit breaker or fuse (not included) as close as possible to the power source. Failing to install an inline circuit breaker or fuse can result in a fire hazard in the event of a short circuit.

The maximum extension length for the LC102 module power cable depends on the power source:

For a 12 Vdc power source: up to 7.5 metres (24 ft 7 in).For a 24 Vdc power source: up to 15 metres (49 ft 2 in).All extensions must use marine-grade 16 AWG (1.3 mm²) wire.

You can connect a normally open momentary switch (not included) to the Garmin Spectra LED control module to turn all connected LED lights on and off without using a chartplotter, stereo, or app. To do this, connect the pink and black wires from the power cable harness to the same ground connection as the negative wire, via the momentary switch.

To wire LED lights to the module:

Disconnect the power supply from the Garmin Spectra LED control module before making any connections to prevent accidental short circuits. Use the cable harnesses provided with the module. The extension cable required to connect the LED lights to the cable harnesses is not included, but a marine-grade LED cable (010-13386-00) is available from Garmin. Connect the wire to the LEDs in accordance with the documentation provided with your LED lights. Connect the wire to the cable harnesses using appropriately sized marine-grade connectors or solder and heat-shrink tubing. LED wire colors are: Dark blue: LED power (+VE) Light green/black: Cool white LED (-VE) Red/black: Red LED (-VE) Green/black: Green LED (-VE) Light blue/black: Blue LED (-VE) Yellow/black: Warm white LED (-VE) Connect the cable harnesses to the ports on the Garmin Spectra LED control module.

The Spectra LC102 module is compatible with Garmin chartplotters and Fusion stereo systems, provided they are connected to the same NMEA 2000 network. It is also compatible with the ActiveCaptain app for LED light control.

Yes, the Spectra LC102 module is compatible with the NMEA 2000 network. It must be connected to the same NMEA 2000 network as the chartplotter or stereo you wish to use to control the LED lighting.

No, the supply voltage of the LED control module must match the voltage of the LED lighting it controls. Mixing 12 Vdc and 24 Vdc devices can damage your LED lights.

No, the Spectra LC102 module requires power from a dedicated power connection and does not draw power from the NMEA 2000 network. Additionally, if you use a 24 Vdc power source for the module and LEDs, you must not connect the NMEA 2000 network to this 24 Vdc source.

Garmin’s limited warranty does not cover:

Cosmetic damage such as scratches, scuffs, and dents.
Consumables like batteries, unless the damage is due to a material or manufacturing defect.
Damage caused by an accident, misuse, abuse, water, flood, fire, or other natural disasters or external causes.
Damage caused by service performed by a person who is not an authorized Garmin service provider.
Damage to a product that has been modified or altered without Garmin’s written authorization.
Damage to a product that has been connected to power and/or data cables not supplied by Garmin, or to uncertified UL power adapters and cables not labeled as Limited Power Source (LPS).

Before requesting warranty service, please consult the online help resources available at support.garmin.com. If your device is still not functioning correctly after using these resources, contact an authorized Garmin service center in the country of original purchase or follow the instructions on support.garmin.com to obtain warranty service. An original or copy of the sales receipt from the original retailer is required for warranty verification.