VeX™ mounting bracket for enclosed speaker, 1.625 in (PS-SWMCP-B-1.625)

This mounting bracket is designed to secure JL Audio VeX™ enclosed speaker systems to round bars. It enables a secure installation and allows the speaker to be angled.

This mount is specifically compatible with JL Audio PS650-VeX™ sealed enclosure systems.

This mount model is designed for bars with a diameter of 1.625 inches.

No, this mount is specifically designed as a swivel fitting for round pipes, as stated in the installation instructions.

The mounting bracket comes with the following components:

4 Axia Alloys hose clamps
6 M6 x 16 mm socket head screws
2 M4 x 4 mm set screws (pre-installed)
4 M6 Nylstop nuts
2 hose clamp receivers
1 tube of Loctite® Red thread locker
4 M6 flat washers
1 M6 x 45 mm socket head screw
1 plastic strip

No, the mounting base, silicone adhesive, #8 flat washers, and #8 x 1-1/4" pan head screws are included with the VeX™ speakers, not with this mount alone.

To avoid scratching the bar, it is recommended to place the supplied plastic strip around the pipe before pushing the hose clamps onto it.

Yes, a Loctite® Red thread-locking compound is included with the mounting bracket.

Installation takes place in several steps:

Loosen the pre-installed M4 x 4 mm set screw in the clamp receiver. Pass an M6 x 16 mm screw through the central hole of the clamp receiver into the central hole of the mounting base and hand-tighten. Place the plastic strap around the pipe, then slide the clamps onto the pipe. Align the clamps with the clamp receiver on the enclosure. Apply red Loctite® to two M6 x 16 mm screws, pass them through the slots of the clamp receiver into the appropriate holes of the mounting base, and tighten fully. Remove the central M6 x 16 mm screw from the clamp receiver, apply red Loctite®, reinstall it, and tighten fully.

Yes, you can rotate the speaker to the desired angle. To do this, you must reinstall the speaker and the speaker mounting screws with their washers, tightening by hand in a cross pattern.

To install the aluminum logo cap:

Clean the inside of the cap with acetone (not included) before attaching it to the enclosure. Apply a circular bead of silicone adhesive (included with VeX™ enclosures) inside the cap, 1/2 inch (13 mm) from the outer edge. Align the aluminum logo cap at the desired rotation angle and press it onto the back of the enclosure. Use tape (not included) to hold the cap in place until the silicone cures (at least 24 hours).

JL Audio guarantees this product against defects in materials and workmanship for a period of two (2) years from the original purchase date.

No, this warranty is not transferable and applies only to the original buyer from an authorized JL Audio dealer.

Damage caused by the following situations is not covered by the warranty:

Accident, misuse, abuse, modification, or negligence of the product. Failure to follow installation instructions. Unauthorized repair attempts. False statements by the seller. The warranty also does not cover consequential or indirect damage, nor the cost of removal or reinstallation of the unit or units. Aesthetic damage due to an accident or normal wear is not covered.

This mounting bracket is manufactured in the United States by Axia Alloys.

Yes, this mounting bracket is protected by US patents no. 8,136,771 and 8,398,035.

This specific product (PS-SWMCP-B-1.625) is designed for 1.625-inch diameter bars. The manual refers to other sizes for illustration, but this model is only for 1.625 inches.

Yes, this mount is a swivel fixture designed to allow the enclosure to rotate to the desired angle.

Yes, two M4 x 4 mm grub screws are preinstalled in the clamp receiver.

The main screws used are M6 x 16 mm and M6 x 45 mm countersunk screws, secured with M6 Nylstop nuts and M6 flat washers.