AC Master 24/2000 inverter (230 V 50/60 Hz, EU Schuko plug)

The Mastervolt AC Master 24/2000 inverter converts a 24 V battery voltage into a stable 230 V AC power supply at 50/60 Hz. It delivers a pure sine wave, making it suitable for powering sensitive electronic equipment in recreational and semi-professional applications.

The AC Master 24/2000 inverter delivers a continuous power output of 2000 W at an ambient temperature of 40 °C. It can also handle peak loads up to 2300 W for 1 minute and 4000 W for 1 second.

Yes, this Mastervolt AC Master inverter is a pure sine wave model. This ensures a stable and reliable power supply, essential for the proper operation of sensitive electronic equipment without risk of damage or malfunctions.

The Mastervolt AC Master 24/2000 inverter has dimensions of 248 mm (height) x 443 mm (width) x 83 mm (depth). Its weight is 5.24 kg.

The operating ambient temperature range for the Mastervolt AC Master 24/2000 inverter is -20°C to 60°C. However, power derating occurs above 40°C (at 60°C, power is reduced to 40%).

The Mastervolt AC Master inverter integrates an automatic energy-saving system. This mode can be enabled via DIP switch 4. In energy-saving mode, no-load consumption is significantly reduced, extending battery autonomy.

The no-load power consumption of the Mastervolt AC Master 24/2000 inverter is as follows:

In normal mode (ON): less than 1.0 A at 24 V. In energy-saving mode: less than 0.05 A at 24 V.

The Mastervolt AC Master inverter integrates several protections to ensure safe and reliable operation:

Battery low-voltage protection (shutdown at 21.0 V, restart at 25.0 V).Battery high-voltage protection (shutdown at 33.0 V, restart at 29.0 V).Overload protection.Internal temperature protection.

In case of overload, the Mastervolt AC Master inverter goes into protection mode. To resolve this issue, it is recommended to reduce the connected load and/or check the AC wiring for potential short circuits. After correction, the inverter can be manually reset by turning off and then back on the main switch.

For a secure installation, the grounding point of the Mastervolt AC Master inverter must be connected to the central grounding point of the vehicle or boat. Proper grounding is crucial for the safety of the entire electrical system.

For the AC Master 24/2000 model, the minimum recommended DC cable cross-section is 35 mm² (2 AWG). It is essential to use cables of the appropriate cross-section to avoid voltage drops and ensure the performance and safety of the installation.

For 12 V and 24 V models, including the AC Master 24/2000, the minimum recommended AC cable cross-section for the output is 1.50 mm² (16 AWG). This ensures safe and efficient distribution of AC power to connected devices.

Yes, it is imperative never to use the Mastervolt AC Master inverter in an area where there is a risk of gas or dust explosions. The installation environment must be dry, well-ventilated, and within the specified ambient temperature ranges.

If the LED indicator signals a DC input voltage that is too low (red, slow blinking), you must:

Check if the voltage drop is caused by DC cables that are too long or have an insufficient cross-section; if so, shorten the cables or use a larger gauge.Tighten any loose or corroded connections; burnt cables must be repaired immediately.If the battery is dead, disconnect the load and recharge the battery.

The Mastervolt AC Master 24/2000 inverter is designed to operate with a battery system with a nominal voltage of 24 V.

Yes, the inverter’s AC output voltage is selectable. You can adjust the voltage between 200 V, 220 V, 230 V, and 240 V using DIP switches 1 and 2 located on the device.

Yes, the output frequency of the Mastervolt AC Master 24/2000 inverter is adjustable. You can select between 50 Hz and 60 Hz using the DIP switch 3.

The Mastervolt AC Master 24/2000 inverter is equipped with an EU (Schuko) AC output socket, compliant with European standards.