Satellite reception antenna 33 STV North America (replace E42170)

The Raymarine 33 STV satellite reception antenna is a satellite TV system designed for marine environments. This system enables automatic identification, acquisition, and tracking of compatible signals from digital video broadcast (DVB) satellites, providing access to hundreds of TV channels at sea or dockside.

Version E70453 of the 33 STV antenna is specifically configured for circularly polarized signals, making it compatible with satellites covering North America.

The 33 STV system is supplied with the following items:

The antenna unitThe antenna control unit (ACU)An installation kit including bolts, flat washers, spring washers, and self-tapping screwsThe necessary cables: a 10 m power cable (R08321) to connect the ACU to the DC power supply and a 3 m RF cable (R08257) to connect the ACU and the integrated receiver-decoder (IRD).

No, it is critical not to paint the antenna unit or apply any other finish. This could degrade its performance beyond acceptable limits.

Yes, Raymarine equipment and accessories comply with the applicable electromagnetic compatibility (EMC) regulations for recreational marine environments. Proper installation is required to ensure EMC performance is not compromised. This product also complies with European Directive 2004/108/EC and bears the CE conformity mark.

Yes, to access all features of your STV system, you must subscribe to the relevant service(s) with the appropriate service provider(s).

Yes, the Raymarine 33 STV North America antenna (E70453) is designed to replace the E42170 model.

No, the 33 STV E70453 antenna is configured for circularly polarized signals used in North America. Systems for Europe, Australia, New Zealand, China, and the Middle East use linearly polarized signals and are not compatible with this version.

If you change your operational geographic zone, you may need to make several adjustments:

Adjust the LNB (Low Noise Block) unit of the antenna. Change the software of your ACU (Antenna Control Unit). Change your satellite receivers (IRD). For more details on changing the geographic zone, it is recommended to contact Raymarine product support.

The 33 STV E70453 antenna is designed to receive signals with circular polarization, which are transmitted by satellites covering North America. It cannot receive signals with linear polarization.

If your Raymarine equipment must be connected to other devices using a cable not supplied by Raymarine, a suppression ferrite MUST always be attached to the cable near the Raymarine unit. This is essential to ensure correct EMC performance.

For optimal EMC performance, Raymarine equipment and its connected cables should be:

At least 1 metre (3 feet) away from any equipment transmitting radio signals or cables carrying such signals (e.g., VHF radios, cables, and antennas). For SSB (Single Sideband) radios, this distance must be increased to 2 metres (7 feet). More than 2 metres (7 feet) from the path of a radar beam. A radar beam typically propagates within 20 degrees above and below the radiating element.

When installing this product, ensure the power source is properly protected by a fuse or appropriately rated circuit breaker. It is also important that the product is powered by a battery separate from the one used for engine starting. This prevents erratic behavior and data loss that can occur if the engine start does not have a dedicated battery.

Yes, before installing or using the product, you must open the antenna unit cover and remove the transit foam inserts from the base of the unit.

When lifting the antenna unit, always lift it by its base plate. Do not use the antenna cover to lift it, as this could damage it. Additionally, take care to avoid damaging the connectors located under the antenna's base plate when moving the unit and do not use them to lift the unit.

Yes, the Raymarine cables provided can be fitted with suppression ferrites, which are important for correct EMC performance. If a ferrite must be removed for any reason (e.g., installation or maintenance), it must be replaced in its original position before using the product. Use only the correct type of ferrites, supplied by Raymarine authorized dealers.

It is recommended to keep the antenna more than 2 metres (7 feet) away from a radar beam path. A radar beam typically propagates 20 degrees above and below the radiating element.

It is recommended not to cut or extend cables unless specifically detailed in the product installation manual.

To register ownership of your Raymarine product and receive all warranty benefits, you can spend a few minutes filling out the warranty registration card provided in the box, or visit www.raymarine.com to register online. It is important to affix the barcode label showing the unit’s serial number to the warranty registration card.

No, the equipment described in this document is intended for use on recreational craft and workboats not covered by the International Maritime Organization (IMO) and International Convention for the Safety of Life at Sea (SOLAS) transport regulations.