Manual bilge pump Gusher Urchin - deck-mounted with neoprene gaskets

Before ordering and installing the Whale Gusher Urchin BP9005 pump, it is essential to check its compatibility. We recommend that you:

Verify the exact part number (BP9005) to ensure it matches your requirements. Confirm compatibility with the existing components on board your vessel, including dimensions, connection type, and available space for "deck-mounted" installation.

Yes, Gusher Urchin pump models, including the BP9005, offer considerable flexibility in choosing the handle position relative to the flow direction. To adjust the orientation:

Loosen the pinch bolt.Remove the clamping ring and slightly lift the diaphragm.Rotate the pump body to the desired position.Reinstall the diaphragm, clamping ring, pinch bolt, and nut.Note that the inlet is always positioned 180 degrees from the outlet.

If your pump fails to prime or seizes, check the following:

Obstructions: Check for blockages in the intake hose or air leaks at the pump connection. Clear any obstructions.Diaphragm: Inspect the diaphragm for tears. If damaged, a service kit is required.Valves: Check for debris under the valves or if the valves are deformed. A service kit can resolve this issue.Intake hose: Ensure the intake hose does not collapse during the intake stroke. Using a reinforced hose is recommended.

The Whale Gusher Urchin BP9005 manual bilge pump is fitted with neoprene seals. These seals are selected for their durability and resistance in the marine environment, ensuring good sealing and performance.

Whale pumps are warranted for 5 years from the date of purchase against material and manufacturing defects. For rubber parts, the warranty is 1 year.

The Whale Gusher Urchin BP9005 manual bilge pump is designed specifically for manual pumping and draining of your boat's bilge. It is part of Whale's Gusher Urchin range, known for its reliability.

This is a manual bilge pump, specifically the Gusher Urchin model, designed to be installed on deck. It is used for manual pumping and bilge drying.

The Gusher Urchin BP9005 pump is fitted with neoprene seals, making it suitable for pumping clean bilge water. The manufacturer offers service kits with nitrile seals (part number AK9011) for oily bilge water on other models, but the BP9005 is specifically designed for clean water.

The pump is equipped with stepped inlet and outlet fittings, allowing the use of 25 mm (1 inch) or 38 mm (1 1/2 inch) diameter hoses. If the larger diameter is required, the 25 mm section must be cut off.

Yes, the pump offers great flexibility in choosing the handle position relative to the flow direction. The pump body can be rotated after loosening the pinch screw and removing the clamping ring, then repositioned. The inlet is always 180 degrees from the outlet.

The pump must be installed in a position where it can be operated comfortably with a full range of motion of the handle. It is secured using 6 mm (1/4 inch) bolts. For minimal pumping effort, it is ideal to position it midway between the strainer and the hull outlet.

Use a high-quality reinforced hose with a smooth bore. Avoid sharp bends in the suction hose. High-quality stainless steel worm-drive hose clamps must be firmly secured at all connections.

To ensure watertight seals, it is essential to use high-quality stainless steel worm-drive hose clamps, firmly secured at all pipe connections.

Yes, male and female elbows (references EB3364 for 25mm/1" and EB3488 for 38mm/1 1/2") are available to connect directly to the pump fittings, making installation easier in tight spaces.

Yes, the pump is designed to be compatible with two different pipe diameters. Its inlet and outlet fittings are stepped, allowing the use of 25 mm (1 inch) or 38 mm (1 1/2 inch) pipes. To use the larger diameter, the 25 mm section must be cut off.

The recommended service kit for the Gusher Urchin BP9005 pump, which uses neoprene seals for clean bilge water, is part number AK9003. It is advisable to keep one onboard.

Whale pumps are warranted for 5 years from the date of purchase against material and manufacturing defects. Rubber components are covered by a 1-year warranty.

The pump’s pumping capacity depends on installation conditions and pumping rate. For detailed flow rates in gallons (litres) per minute based on lift height and strokes per minute, refer to the manufacturer’s performance charts for 1" (25mm) and 1 1/2" (38mm) hoses.

Regular inspection of the pump is recommended. Rubber components must be replaced if worn or every three years, regardless of condition. Service kits are available for replacing these parts.

The Whale Gusher Urchin BP9005 manual bilge pump is designed for installation on the deck of your vessel. Below are the key steps and information for its installation:

Positioning: Choose a location where the pump can be operated comfortably, allowing full movement of the handle. Mounting: The pump must be securely fastened using 6mm (1/4 inch) bolts. Flow direction: The pump offers flexibility to adjust the flow direction. You can rotate the pump body to orient the inlet and outlet as needed. The inlet is always positioned 180 degrees from the outlet. To do this, loosen the pinch bolt, remove the clamping ring, slightly lift the diaphragm, and rotate the body to the desired position before retightening everything. Hose connections: The inlet and outlet fittings are stepped, allowing the use of two different hose diameters: 25mm (1 inch) or 38mm (1 1/2 inches). If you require the larger diameter (38mm), simply saw off the 25mm section of the fitting. Sealing: Ensure perfectly watertight joints by using high-quality stainless steel hose clamps. Recommended hoses: It is advisable to use a high-quality smooth-bore reinforced hose for suction and to avoid sharp bends.