Smart BMS CL 12-100

The Victron Energy Smart BMS CL 12-100 is an all-in-one battery management system (BMS). It is specifically designed for Victron Smart 12.8 V lithium batteries and 12 V systems equipped with an alternator, particularly in vehicles and boats. Its primary function is to protect and monitor each individual cell of the battery.

This BMS is specifically designed for Victron Smart 12.8 V lithium batteries. It provides protection and monitoring for each individual cell within these batteries.

Up to 20 Victron Smart 12.8 V lithium batteries can be connected in a single system managed by this BMS.

In a 12 V system, the Smart BMS CL 12-100 can manage a maximum energy storage capacity of 84 kWh by connecting up to 20 batteries.

The Alternator/Starter Batt+ port provides current limiting and unidirectional current flow from the alternator to the lithium battery. This allows safe connection of any 12 V alternator (and starter battery) to the lithium battery while protecting the alternator from overload and the lithium battery from excessive charging currents.

The Smart BMS CL 12-100 protects the alternator by electronically limiting the input current on the Alternator/Starter Batt+ port to approximately 90% of the fuse rating. For example, with a 100 A fuse, the input current is limited to about 90 A. This limitation prevents the alternator from overheating and failing during prolonged operation at full power.

No, the current flow is unidirectional. The Smart BMS CL 12-100 prevents current from flowing from the lithium battery to the starter battery, protecting the lithium battery from deep discharge.

The BMS monitors and protects each individual battery cell. It will disconnect the alternator, charging sources or DC loads in case of:

Low or high battery cell voltageExcessive temperature

The pre-alarm output can be used to activate a relay, an LED or an audible alarm. It emits a warning signal before the BMS disconnects the batteries from the system in case of imminent low cell voltage. The alarm is triggered with a minimum delay of 30 seconds before the load disconnection output is deactivated.

The Smart BMS CL 12-100 features electronic protection rated IP65. This means it is protected against dust and low-pressure water jets from all directions.

The Smart BMS CL 12-100 dimensions are 65 x 120 x 224 mm (height x width x depth). Its weight is 1.6 kg.

Monitoring, initial configuration, and diagnostics of the BMS are performed via Bluetooth using the VictronConnect application. This application allows real-time viewing of key parameters.

The "Instant Readout" is a feature of the VictronConnect application that allows you to read the most important BMS values in real time without needing to connect to the BMS. This makes quick diagnostics easier and provides a greater range than standard Bluetooth connections.

Yes, it is designed to be safely connected to any 12 V alternator via its dedicated input, which provides current limiting and protection against alternator overload.

This BMS was specifically designed for 12 V systems equipped with an alternator, such as those found in vehicles and boats.

No, the Smart BMS CL 12-100 is an all-in-one battery management system specifically designed for Victron Smart 12.8 V lithium batteries. It is not compatible with batteries from other brands.

The load disconnect output can be used to control DC loads with a remote on/off input, such as BatteryProtect devices, inverters, or DC-DC converters. It cuts the load in case of cell undervoltage risk to prevent deep discharge.

The load-disconnect output can remotely control the on/off state of various chargers, including the Phoenix Smart Charger IP43, a Cyrix-Li-Charge relay, or a Cyrix-Li-ct battery combiner. It allows interrupting the charge in case of cell overvoltage or excessive temperature.

The Smart BMS CL 12-100 case contains the following items:

The Smart BMS CL 12-100A 10 mm earth wire with 10 mm eyelet terminalA 2-pin plug with pre-installed wire loopA 3-pin plug for charge/discharge disconnection and pre-alarmA pre-installed Megafuse 100 A fuseAn ATO fuse holder with 2 x 7.5 A fuses

During installation, it is mandatory to comply with national safety regulations. Installation must be carried out exclusively by qualified and trained installers. Before modifying any connections, the system must be powered off and hazardous voltages must be verified as absent. It is also critical not to discharge a new lithium battery before it has been fully charged, and to charge it strictly within the specified limits.