ECLIPSE 18 inches, wide-beam spotlight

The Garmin ECLIPSE Flood Light 18" spotlight is equipped with 12 x 10 W LEDs, delivering up to 10,000 lumens. It provides a 5000 K color temperature and a wide beam angle of 70 to 90 degrees.

This spotlight operates within a voltage range of 10.5 to 31 VDC.

The maximum power draw of the spotlight is 9.2A at 12V and 4.6A at 24V, for an average power output of 110 W.

The spotlight can be controlled in several ways:

Via a simple on/off switch.Via a momentary switch.Using a compatible multifunction display (MFD).With a smart device.For control via MFD or smart device, the addition of an ECLIPSE Command Center or an EOS-LUX Command Center is required.

Once integrated into an MFD or smart device via a Command Center, the projector can provide dynamic lighting effects such as strobe and dimming mode.

Yes, this spotlight has an IP68 protection rating, making it resistant to dust and immersion.

The projector housing is made of powder-coated aluminum and features a frosted lens.

The mounting location must be a flat and durable surface.

The mounting bracket uses a 6.5mm hole sized for an M6 bolt (included). A 7mm hole is also required for cable routing.

The spotlight must be secured to the brackets with a tightening torque of 5Nm. It is important not to overtighten.

Yes, this product must be installed, inspected, and maintained only by a qualified electrician, in accordance with all applicable electrical codes.

The cable entry must be made watertight. Using a gland is recommended.

Yes, the spotlight can operate with a simple on/off switch (latching switch).

To activate dimming with a toggle switch:

Turn the switch on to power the light at full brightness. Toggle the switch once to start the dimming cycle. Toggle the switch again to pause the dimming cycle. Turn the switch off for 5 seconds to restart at full brightness.

No, the ECLIPSE Command Center installation is only suitable for 12V boats.

Use only water and soap with a soft cloth to clean the projector. Do not use any chemical cleaners and do not clean under pressure. Regular inspection of the projector must be performed.

LUMISHORE Ltd guarantees its lighting systems, including lights and associated accessories, against manufacturing defects for a period of three years from the initial date of purchase.

The warranty may be voided in case of misuse, abuse, incorrect installation, negligence, improper shipping, damage caused by disasters (fire, flood, storm, lightning), installation by unqualified personnel, unauthorized repair or modification, or unapproved installations. Failure to comply with installation, maintenance, and usage instructions also voids the warranty.

To control multiple lights via an MFD, you will need an LUX Light Control Module and an EOS-LUX Command Center.

Installation of the Garmin ECLIPSE Flood Light 18-inch must be performed by a qualified electrician in accordance with all applicable electrical codes. It is imperative to ensure that the power supply is cut off before and during installation and maintenance.

Physical installation steps:Selecting the mounting location: Choose a flat and durable mounting location.Drilling mounting holes: Use an appropriate drill bit to drill the support holes. The bracket has a 6.5 mm hole suitable for an M6 bolt (provided).Cable routing: Drill a 7 mm (0.275 inch) hole for the cable. The cable must always be in a "fixed" position without movement or rotation. The cable entry must be sealed; using a cable gland is recommended.Attaching the brackets: Secure the brackets in place using the provided M6 bolts and nylon insert nuts. Apply the appropriate torque based on the fasteners used and the mounting surface.Installing the light: Mount the ECLIPSE light onto the brackets using the provided M6 bolt, washers, and nylon insert nut. Ensure the nylon washers are placed inside the stainless steel bracket. Tighten to 5 Nm torque, WITHOUT OVER-TIGHTENING.Wiring and testing: Wiring must be done according to ABYC guidelines. The light operates within a voltage range of 10 to 31 VDC.

Simple control (toggle switch):Turn the switch to power the light at full brightness.Press the switch once to start the dimming cycle.Press the switch again to stop the dimming cycle.Turn the switch off for 5 seconds to restart at full brightness.Control via multifunction display (MFD): For MFD control, you will need an ECLIPSE Command Center or an EOS-LUX Command Center.With an ECLIPSE Command Center (12V boats only): Connect the ECLIPSE wiring harness (RED) to the FL18's RED, the YELLOW to the FL18's YELLOW, and the WHITE and BLUE to the FL18's BLACK.With multiple lights using an ECLIPSE Command Center, connect each FL18's RED to +10.5-15V (with individual fuse), each FL18's BLACK to ground, and the ECLIPSE harness YELLOW to each FL18's YELLOW.With an LUX Light Control Module and EOS-LUX Command Center: This system allows control of up to 16 lights. Operation is via a momentary switch: press to turn on, hold to adjust brightness, press to turn off.It is crucial to always cut the power supply before any intervention and ensure all connections are watertight to guarantee product safety and performance.