Szonde GT56UHD-TR – Garmin Force® / Force® Pro elektromos motorokhoz

Yes, to achieve the best possible performance and to avoid potential injuries or damage to the device or your vessel, installation by a qualified marine technician is strongly recommended. It is imperative to strictly follow the mounting instructions.

Yes, a medium-strength thread locking compound, such as LOCTITE 243™, is absolutely required on the threads of the four mounting holes located on top of the propeller motor. This ensures a watertight and secure connection between the shaft base and the propeller motor, preventing water ingress and potential damage to the motor.

The Garmin GT56UHD-TR is a replacement transducer kit designed specifically for Garmin Force® and Force® Pro electric motors. Its primary function is to maintain the integrity and sonar performance of these motors, ensuring the continuity of UHD (Ultra High Definition) sonar capabilities essential for detecting structures and fish.

The Garmin GT56UHD-TR is a transducer replacement kit. It is designed to replace an existing transducer on Force® and Force® Pro electric motors, not for a first-time full installation of the transducer on a boat.

The Garmin GT56UHD-TR is specifically designed to be compatible with Garmin Force® and Force® Pro electric motors. It is not intended for use with other Garmin motor models or other brands.

Yes, it is necessary to update the software of your Garmin chartplotter when installing this depth sounder to ensure optimal performance and full compatibility.

Yes, if the depth sounder cable is not long enough to reach the chartplotter, you can add a Garmin extension cable (Garmin part number 010-11617-42 or 010-11617-32). However, to avoid signal degradation, it is recommended not to extend the cable by more than 9 meters (30 feet).

For replacing the transducer, you will need the following tools:

Phillips screwdriver #2 and #33 mm and 4 mm hex bits or sockets (a 4 mm ball-end hex bit is strongly recommended due to the angle of some screws)A torque wrenchMedium-strength thread locker, such as LOCTITE 243™Compressed air can or an air compressor

To achieve the best possible performance and avoid potential injuries or damage to the device or the boat, installation by a qualified marine technician is recommended. It is important to read the instructions in full and ensure you have the necessary tools and skills to perform the service correctly.

Before any manipulation or work on the propeller, the propeller motor, electrical connections, or electronic housings, it is imperative to always disconnect the motor from the battery to avoid serious injury or death. Additionally, be aware of the risk of crushing or pinching due to moving parts when stowing or deploying the motor.

Yes, using a medium-strength thread locking compound, such as LOCTITE 243™, is mandatory. It must be applied to the threads of the four threaded holes located on top of the propeller motor. This is crucial to maintain a watertight connection between the shaft base and the propeller motor, and to prevent water ingress that could damage the motor.

Yes, new O-rings of different sizes (e.g., 78 mm and 36 mm) and grease packets are included in the replacement kit. The grease must be applied to the new O-rings before placing them in the corresponding grooves on the shaft base and on top of the propeller motor. This ensures proper sealing and water protection.

When pulling cables, always pull on the cable itself and not on the cable connectors. The data cable connector is fragile and may break if pulled. It is also recommended to straighten, align, and bundle the cables with tape if they are not already, so they pass smoothly through the shaft.

No, the cables connected to the transducer must never be cut. Cutting the transducer cables voids the product warranty. If the cable is too short, an official Garmin cable extension must be used.

You must use the new screws, washers, O-rings and other parts supplied in the replacement kit. The old screws, washers and seals must be discarded. Using new parts is essential to ensure the watertightness and durability of the installation.

Before replacing the depth sounder, you must prepare the engine by performing the following steps:

Disconnect the engine from the power source.Open the shaft housing cap.Disconnect the cables inside the shaft housing cap.Remove the depth sounder cable from the shaft housing cap.Remove the shaft housing cap.Remove the shaft from the steering system.

After preparing the engine by removing the shaft from the steering system, the steps to remove the existing sensor are:

Remove the skeg and the nose cone from the propeller shaft.Remove the propeller shaft from the shaft.Remove the sensor from the nose cone.It is important to follow these steps carefully to avoid damaging the components.

After removing the existing transducer, the key steps to install the replacement transducer are:

Install the new transducer in the nose cone, using the new neoprene pad, the new screws and washers provided. Install the propeller drive on the shaft, applying grease to the O-rings and thread-locking compound to the mounting screws. Install the nose cone and skeg on the propeller drive. Ensure all new parts provided in the kit are used and torque values are followed.