Garmin Reactor™ 40 Compact automata indítócsomag hidraulikus kormányzású hajókhoz

The Reactor™ 40 Compact Autopilot Starter Pack is an advanced autopilot system designed by Garmin for vessels equipped with hydraulic steering systems. It provides precise and reliable navigation, featuring simplified configuration options for optimal commissioning. Its compact design makes it particularly suitable for boats where space is limited.

This autopilot is specifically designed for vessels equipped with hydraulic steering systems. It integrates with existing steering systems to automate navigation.

The 'Compact' format of the Reactor™ 40 is specifically designed for vessels where space is limited. It allows for easier installation in tight areas while maintaining the performance and reliability expected from a Garmin autopilot.

The Command Course Unit (CCU) is the main sensor of the Reactor™ 40 Compact autopilot system. It is essential for system operation, as it provides the heading data required for precise boat steering.

Yes, installing the Reactor™ 40 Compact autopilot system requires marine expertise. Specific knowledge of hydraulic steering components and marine electrical systems is necessary for correct installation and to prevent damage to the boat or the product.

The Dockside Wizard is an intuitive setup assistant that guides the user through the initial autopilot configuration. It allows configuring parameters such as:

The vessel typeLock-to-lock rudder lock valueRudder sensor calibrationRudder direction testIt can be completed when the boat is docked or out of the water, provided the boat is stationary if in the water.

The Sea Trial Wizard is a setup assistant that calibrates the autopilot’s core sensors under real sailing conditions. It must be completed in calm waters and at a location suitable for your sailboat. It includes:

Compass calibrationThe Autotune procedure to optimize steering performance based on the sailboat’s specific dynamics.It must be performed after the Dockside Wizard and before fully using the autopilot.

To test a location for magnetic interference, use a handheld compass:

Hold the compass at the planned mounting location for the CCU.Move the compass 15 cm (6 inches) to the left, then to the right of the location.Observe the needle: if it moves more than three degrees, magnetic interference is present. Choose a new location and repeat the test.Repeat this process by moving the compass above and below, as well as in front of and behind the mounting location.If the compass needle does not move or moves less than three degrees, the location is suitable.

When installing the ECU, consider the following points:

The ECU can be mounted on a flat surface in any orientation. It must be installed within 0.5 m (19 inches) of the pump, as the connection cables between the ECU and the pump cannot be extended. The ECU must be placed where it will not be submerged or exposed to splashes. Mounting screws are provided, but additional screws may be required if the supplied ones do not suit the surface.

The hydraulic pump must be mounted in a location where you can extend the boat's hydraulic steering lines. Ideally, it should be mounted horizontally. If vertical mounting is required, the hydraulic connections must face upward.

The Shadow Drive is a sensor installed in the hydraulic steering lines of your boat. It detects when you take manual control of the helm and suspends the autopilot's control. It must be mounted horizontally and as level as possible, securely fastened with cable ties.

Regarding its placement:

It must be mounted lower than the lowest helm but higher than the pump. It must not be directly connected to the fitting at the back of the helm or to a hydraulic T-fitting. A length of hose must separate the Shadow Drive from these components.

In a single-helm installation, there must be no T-fitting between the helm and the Shadow Drive.

In a double-helm installation, the Shadow Drive must be installed between the pump and the hydraulic T-fitting leading to the upper and lower helms, closer to the T-fitting than to the pump.

It must be installed in the starboard or port steering line, not in the return line or high-pressure line.

For the installation of the system, you will need the following tools:

Safety glassesDrill and drill bitsWrenchesHole saw 90 mm (3.5 inches) or rotary cutting tool (for optional tiller drive installation)Wire cutters/strippersPhillips and flat-head screwdriversCable tiesSPST unipolar unidirectional switch (if Shadow Drive is not installed)Waterproof wire connectors or heat-shrink tubing and heat gunMarine sealantMarine corrosion inhibitor sprayPortable compass (to test magnetic interference)Hydraulic hose with factory crimped or field-replaceable fittings (minimum pressure 1000 psi)Hydraulic T-fittingsHydraulic fluidThread sealantHydraulic bleeding kitNote that mounting screws are provided for main components, but you may need different screws if the supplied ones do not fit your mounting surface.

Yes, some cables can be extended, while others cannot:

The CCU cable (5 m / 16 ft) can be extended if the CCU cannot be mounted within 5 m of the ECU. Extensions are available.
The ECU power cable, which connects to the boat’s battery, can be extended if necessary.
The alarm wires can be extended using 28 AWG (0.08 mm²) wire.
The Shadow Drive wires (or manual switch) can be extended using 28 AWG (0.08 mm²) wire.
However, the cables connecting the ECU to the pump cannot be extended. Therefore, the ECU must be mounted within 0.5 m (19 in) of the pump.

Yes, the heading control unit (CCU) and tiller pilot (if included) must be connected to an NMEA 2000 network. If your boat does not already have one, a basic network can be built using the NMEA 2000 cables and connectors included in the package.

Yes, to use the advanced features of the autopilot, optional NMEA 2000 devices can be connected to the NMEA 2000 network. This includes sensors such as a wind sensor, a speed through water sensor, or an external GPS device, which can enhance the data available to the system.

Garmin recommends using a reliable speed source for optimal performance. Options are:

NMEA 2000 tachometer: If one or more NMEA 2000-compatible engines are connected to the network. External GPS: If an NMEA 2000 tachometer data source is unavailable or unusable. Garmin recommends mounting an external GPS antenna with a clear view of the sky for reliable and accurate GPS speed data. Although a 'None' option is available, it is not recommended if the autopilot does not perform well, and it is advised to connect a tachometer via the NMEA 2000 network or use an external GPS antenna as a speed source.

Yes, Garmin has simplified the startup phase with intuitive configuration assistants. The Dockside Wizard guides the user through initial settings, and the Sea Trial Wizard allows calibration of the fundamental sensors in real conditions, including compass calibration and the Autotune procedure.

To register your Garmin device, you can visit garmin.com/express and log in to your Garmin account. It is recommended to keep the original sales receipt or a copy in a safe place.

No, you are responsible for the safe and prudent navigation of your vessel. The autopilot is an assistance tool and does not relieve you of your safety responsibilities. You must always be ready to quickly resume manual control of your boat and never leave the helm unattended.