SplitShot Skimmer szonda

The Navico SplitShot Skimmer transducer is a 2-in-1 transducer that combines High CHIRP wide-angle sonar technology and DownScan Imaging™. It is designed to provide a complete view of fish and underwater structures, offering a versatile solution for anglers.

The SplitShot Skimmer transducer integrates two main sonar technologies:

Traditional High CHIRP wide-angle sonar for standard fish detection. DownScan Imaging™ for detailed views of structures and the seafloor.

The Navico SplitShot Skimmer High CHIRP traditional sonar operates at a frequency of 200 kHz.

The DownScan Imaging™ imagery of the SplitShot Skimmer sounder uses two main frequencies: 455 kHz and 800 kHz.

The High CHIRP traditional sonar of the SplitShot Skimmer fishfinder can reach a maximum depth of 152 metres (500 feet) when operating at 200 kHz.

For DownScan Imaging™ imagery, the maximum depth varies depending on the frequency:

At 455 kHz, the maximum depth is 91 meters (300 feet). At 800 kHz, the maximum depth is 46 meters (150 feet).

The beam width of the High CHIRP sonar in the SplitShot Skimmer fishfinder is 44° at -3 dB when operating at 200 kHz.

The beam widths for DownScan Imaging™ imagery are as follows:

At 455 kHz, the beam width is 55/3° at -3 dB. At 800 kHz, the beam width is 35/1.6° at -3 dB.

The Navico SplitShot Skimmer transducer provides depth and water temperature information.

The Navico SplitShot Skimmer transducer weighs 0.26 kg (0.582 lbs) and is supplied with a 6 m (20 ft) cable.

The SplitShot Skimmer transducer is designed to operate within a temperature range of -15°C to +55°C (5°F to 131°F). For storage, the range is -30°C to +70°C (-22°F to 158°F).

The SplitShot Skimmer transducer can operate effectively up to a maximum speed of 57 knots (55 mph) for detection.

The Navico SplitShot Skimmer transducer is specifically optimized for Lowrance HOOK² and Lowrance HOOK Reveal combos.

The SplitShot Skimmer transducer is equipped with an 8-pin connector, of which 4 pins are wired and used for the connection.

Yes, the Navico SplitShot Skimmer transducer is CE-certified, attesting to its compliance with European standards.

The SplitShot Skimmer transducer offers multiple mounting options to suit different boat types and preferences:

Transom mount on the boat. Mount on a bow electric motor (trolling motor).

The ideal mounting location for the SplitShot Skimmer transducer is an area where the water flow is undisturbed. This ensures optimal sonar performance by avoiding air bubbles or turbulence that could interfere with the signals.

To avoid interference and reduced performance, it is not recommended to install the SplitShot Skimmer transducer in the following locations:

Near planing strakes. Close to flaps, as they can cause significant turbulence in the water flow.

For mounting the transducer with 10 mm diameter screws, the recommended drill bit diameters vary depending on the material:

For soft materials (e.g., plywood), use a drill bit of Ø 3.7–4.0 mm (5/32"). For rigid materials (e.g., fiberglass, acrylic, hardwood), use a drill bit of Ø 4.2–4.7 mm (3/16").

Yes, the Navico SplitShot Skimmer transducer is designed to be installed on a bow-mounted electric motor (trolling motor) in addition to the transom-mount option.