Blue Smart IP67 töltő 12/17(1)

The Victron Energy Blue Smart IP67 12/17(1) charger is fully encapsulated, giving it IP67 protection. This means it is waterproof, shockproof, and protected against ignition. Its housing is made of die-cast aluminum, and the electronics are embedded in resin, ensuring robustness suitable for demanding environments such as the marine environment.

The charger is equipped with Bluetooth Smart technology. You can monitor and configure it remotely using the VictronConnect app on your smartphone, tablet, or other device (compatible with Apple and Android). The app allows you to view battery voltage and current, adjust charging parameters, and update the charger when new features become available.

The Victron Energy Blue Smart IP67 12/17(1) charger has an efficiency of 95% or higher. This means it dissipates three to four times less heat than standard industry chargers. In standby mode, its power consumption is less than 0.5 watts, which is five to ten times better than average.

This charger uses a 5-stage adaptive charging algorithm controlled by a microprocessor. The stages are: bulk (bulk charge), absorption, conditioning, float (trickle charge), and storage. The 'adaptive' function automatically optimizes the charging process based on how the battery is used.

The storage mode activates when the battery has not been discharged for 24 hours. In this mode, the float voltage is reduced to 13.2 V (for a 12 V battery) to minimize gassing and corrosion of the positive plates. Once a week, the voltage is brought back to the absorption level to 'equalize' the battery, thereby preventing electrolyte stratification and sulfation, which are major causes of early battery failure.

Yes, the Victron Energy Blue Smart IP67 12/17(1) charger has a recovery function for fully discharged batteries. It can initiate charging even if the battery has been discharged to zero volts. It can also reconnect to a completely discharged Li-ion battery with an internal disconnect function.

Yes, the charger is protected against overheating. It can be used in hot environments, such as an engine room. The output current will be reduced as the temperature rises above 40 °C (up to 60 °C), but the charger will not fail.

The charger dimensions are 99 mm (height) x 219 mm (width) x 65 mm (depth). Its weight is 2.4 kg.

The charger has two LEDs for status indication:

The yellow LED indicates the charging state: fast blinking for bulk charge, slow blinking for absorption, solid for float, off for storage. The green LED indicates that the device is powered on (power on).

Yes, the Victron Energy Blue Smart IP67 12/17(1) charger can be used as a power supply.

The charger must be installed in a well-ventilated area near the battery. However, it should not be placed directly above the battery due to potential corrosive gases it may emit. Ensure the DC cables are long enough to allow proper placement.

To connect the charger to the battery:

Connect the negative terminal (black cable) to the negative terminal (–) of the battery. Connect the positive terminal (red cable) to the positive terminal (+) of the battery. Then plug the 1.5-meter AC power cable (with CEE 7/7 plug) into the wall outlet. The charging cycle will then begin. It is important to connect and disconnect the DC output terminals only after unplugging the AC cord from the power outlet.

It is crucial to follow safety instructions, including:

Never charge non-rechargeable batteries.Ensure the area around the battery is well-ventilated during charging.Wear full eye and clothing protection.Never smoke and do not allow sparks or open flames near the battery or engine.Never charge a frozen battery.Do not disassemble the charger.Unplug the charger from the outlet before any maintenance or cleaning.

This charger is designed to charge and maintain lead-acid batteries and Li-ion batteries.

The charger is designed for lead-acid and Li-ion batteries with a capacity between 14 Ah and 225 Ah.

Yes, the Victron Energy Blue Smart IP67 12/17(1) charger includes temperature compensation for charging. It measures ambient temperature during the test phase and compensates for temperature during the charging process to optimize the charging voltage of lead-acid batteries. Therefore, no special settings for cold or hot environments are required.

The charging voltage in 'absorption' mode is as follows:

For standard batteries: 14.4 VFor 'High' (high-voltage) batteries: 14.7 VFor Li-ion batteries: 14.2 V

The charging voltage in 'float' (maintenance) mode is as follows:

For standard batteries: 13.8 VFor High batteries: 13.8 VFor Li-ion batteries: 13.5 V

The charger includes multiple protections to ensure safety and durability:

Reverse polarity protection for the battery (via a fuse).Short-circuit protection on the output.Overheat protection, with output current reduction above 40 °C.

The IP67 certification of the Victron Energy Blue Smart 12/17(1) charger indicates a high level of protection, making it perfectly suited for demanding environments. It means the charger is:

Fully encapsulated: Its housing is made of die-cast aluminum and the electronics are completely embedded in resin, ensuring maximum protection.Waterproof: It is protected against water, oil, and dust ingress.Shock-resistant: Its robust design provides excellent impact resistance.Flame-resistant: It is designed to minimize fire risks.These features ensure the charger will not be damaged by water, oil, or dirt, making it ideal for use in marine, industrial, or any other harsh environment.