Adapter NMEA 2000 do czujnika prędkości powierzchniowej/wody GST™ 10

The Garmin GST™ 10 adapter is designed to convert analog data from compatible speed and water temperature sensors into a digital NMEA 2000® signal. It allows displaying this data on compatible Garmin display units connected to your NMEA 2000 network.

The GST™ 10 adapter measures 24.7 mm in width, 17.0 mm in height, and 78.6 mm in length. Its weight is 380 grams.

The GST™ 10 adapter operates within a temperature range of -15°C to 70°C (5°F to 158°F).

Yes, the GST™ 10 adapter is waterproof to IEC 60529 IPX7 standards, meaning it can be submerged to a depth of 1 meter for up to 30 minutes.

The GST™ 10 adapter is powered by the NMEA 2000 bus with a voltage of 9 to 16 VDC. Its maximum power consumption is 0.9 W, and its NMEA 2000 Load Equivalency Number (LEN) is 1 (50 mA).

The GST™ 10 adapter is compatible with water speed sensors, water temperature sensors, or combined water speed and temperature sensors. Among specific Garmin sensors, it is compatible with:

The Garmin through-hull water speed and temperature sensor (Airmar ST850) (part number 010-11413-00).The Garmin water temperature sensor (Airmar T80) (part number 010-11413-01).The Garmin transom-mount water speed sensor (part number 010-10279-02).

The GST™ 10 adapter transmits water speed and surface temperature data to compatible Garmin displays, such as the GPSMAP series or the GMI™ 20 marine instrument display. For a complete list of compatible Garmin chartplotters and devices, it is recommended to consult Garmin's website.

Yes, the GST™ 10 adapter is designed to connect to an existing NMEA 2000® network on your boat. It transmits analog sensor data from compatible sensors to this network. If you do not have an NMEA 2000 network, you will need to build one.

When choosing the location, consider the following points:

The adapter must be installed within 4.4 meters (173 inches) of the sensor, as the sensor connection cable cannot be extended. Choose a location between the main NMEA 2000 network and the sensor. Although the adapter is IPX7 waterproof, avoid locations where it would regularly be submerged. Install the adapter at least 5 cm (2 inches) away from a magnetic compass to prevent electromagnetic interference.

The GST™ 10 adapter must be installed within 4.4 meters (173 inches) of the sensor. The cable connecting the adapter to the sensor cannot be extended.

The connector on the GST™ 10 adapter opposite the NMEA 2000 connector is designed to plug directly into a compatible speed or water temperature sensor. No cutting, splicing, or additional wiring is required.

After connecting the adapter to the sensor, you must connect it to your existing NMEA 2000 network. This typically involves identifying a connection point on the main NMEA 2000 backbone, adding a T-connector there (one is included with the adapter), then plugging the adapter’s NMEA 2000 connector into that T-connector. If the adapter cannot connect directly, an NMEA 2000 drop cable (not included) may be used.

No. If you already have an NMEA 2000 network on your boat, it should already be powered. Do not connect an additional NMEA 2000 power cable to an existing network, as only one power point must be connected to an NMEA 2000 network. The GST™ 10 adapter draws its power directly from the NMEA 2000 bus.

To calibrate water speed, access the NMEA 2000 device list on your compatible Garmin display and select the GST™ 10. Then, depending on your device, choose Review > Calibrate Water Speed or Config > Calibrate Water Speed and follow the on-screen instructions.

To configure the temperature source, go to the NMEA 2000 device list on your Garmin display and select the GST™ 10. Then choose Review > N2K Temp. Source or Config > N2K Temp. Source and select the temperature sensor location.

If the displayed temperature data does not match other devices, you can configure an offset. From the NMEA 2000 device list, select the GST™ 10. Choose Review > Temperature Offset or Config > Temperature Offset, then enter a positive or negative decimal value in degrees to adjust the displayed temperature.

If the option is not displayed, use the generic configuration. Select the GST™ 10 in the NMEA 2000 device list, then choose Review > Generic Config or Config > Generic Configuration. Enter the command: “TEMPSOURCE=YDone”, where Y is a number between 0 and 8, or 13, corresponding to the temperature source location (e.g., 0 for water, 5 for livewell, 6 for bait well, etc.).

This message appears if multiple GST™ 10 adapters are assigned to the same NMEA 2000 temperature source. You must assign a unique sensor number to each adapter. Select each GST™ 10 device from the NMEA 2000 device list, then choose Review > Sensor Number or Config > Sensor Number and assign a unique number. If these options are not visible, use the generic configuration (Generic Config) and the command “INSTANCE=ZDone” for each adapter, where Z is a unique positive number.

Yes, you can restore the factory default settings. This will result in the loss of all custom configurations. To do this, select the GST™ 10 in the list of NMEA 2000 devices on your Garmin display, then choose Review > Factory Defaults or Config > Factory Defaults and confirm.