ECLIPSE SNL100, neonowy Flex, 5 m

The Garmin ECLIPSE SNL100 is a flexible LED lighting solution of neon type, specifically designed for marine environments. It provides continuous and uniform illumination without visible light points, making it ideal for indoor and outdoor installations on vessels.

This Garmin ECLIPSE SNL100 light strip model has a length of 5 meters.

Yes, the Garmin ECLIPSE SNL100 is IP68 rated, meaning it is fully protected against dust and can withstand temporary immersion in water. It is suitable for installation in damp areas, both inside and outside the boat. However, it is not designed for permanent submersion.

Yes, the Neon Flex can be cut to specific lengths. It is important to cut it only at the marked cut points, in 25 mm increments. After cutting, the new ends must be sealed using the provided sealing kit to maintain the product's integrity and waterproofing.

The Garmin ECLIPSE SNL100 has a power consumption of approximately 5 Watts per meter and per channel.

The Garmin ECLIPSE SNL100 is designed to provide continuous illumination without visible light spots, creating a smooth neon-like aesthetic effect.

The Garmin ECLIPSE SNL100 is installed using the supplied stainless steel clips, which should be secured every 300 mm. Before installation, ensure the boat’s power source is disconnected or isolated. It is also important to carefully unroll the tape and allow it to relax for about one hour before positioning.

Yes, the "bend-flex" design of the SNL100 allows it to be adapted to curved surfaces. It can be bent along the vertical axis with a minimum bending radius of 120 mm. However, it is crucial not to twist or bend it along the horizontal axis to preserve its integrity and functionality.

The SNL100 can be installed inside or outside the boat, including in wet areas such as coamings, cabin ceilings, or T-tops. Although it is made from UV-resistant material, it is recommended not to install it in areas exposed to strong direct sunlight to optimize its lifespan.

It is strongly recommended that a qualified professional handle the electrical and mechanical installation of the Garmin ECLIPSE SNL100 to ensure correct and safe installation.

Always unroll the Neon Flex carefully along its entire length; do not lift it by a single end. Do not let the strip fall or twist during installation. Do not apply excessive pressure, as this could damage the internal LED strip. Do not pull, stretch, twist, or bend the Neon Flex on the vertical axis (only on the horizontal axis with the specified bending radius). For lengths over 1 meter, it is recommended to use two people for installation. Always lay the Neon Flex flat and in a straight line; do not allow it to bend, twist, or bunch up.

After cutting the Neon Flex at a marked cut point, use the provided sealing kit. To prevent the sealant from covering the LEDs and causing discoloration, it is important to rewind the Neon Flex onto its reel with the cut points facing outward. This retracts the printed circuit board (PCB) into the extrusion, allowing for effective and clean sealing.

The Garmin ECLIPSE SNL100 is designed to operate only on 12V DC systems. It can function within a voltage range of 10 to 15 Volts DC. Do not connect it to voltages outside this range or directly to an AC power source.

Yes, the Garmin ECLIPSE SNL100 is compatible with ECLIPSE Command Center lighting control systems. For RGB versions of Neon Flex, using an ECLIPSE Command Center and optional expansion modules is mandatory for proper operation and color control.

No, it is important not to add monochrome, bicolor, and RGB lighting on the same zone output of the ECLIPSE Command Center. Use a separate zone output for each type of Neon Flex to ensure correct operation.

No, it is important not to wire the blue and white channels of a two-tone model so that they light up simultaneously. The wiring diagram for two-tone versions is designed for separate control of the colors.

No, the Garmin ECLIPSE SNL100 is designed to operate only with a 12V DC power supply. It must never be connected directly to an alternating current (AC) source.

The Garmin ECLIPSE SNL100 comes with stainless steel mounting clips. If you cut the tape to a custom length, a sealing kit is also included to protect the cut ends.

Yes, the Neon Flex is made from UV-resistant material. However, to optimize its durability and performance, it is recommended not to install it in areas exposed to strong and prolonged direct sunlight.

You can connect a maximum of 20 meters of Neon Flex to a single ECLIPSE Command Center zone.