Kabel magistrali/odgałęźnika NMEA 2000 – wtyk kątowy (2 m)

The main feature of this Garmin 010-11089-00 cable is its 90-degree angled connector. This design is specifically intended for installations where space is limited, making it easier to connect devices with hard-to-reach rear connectors, such as behind multifunction displays or dashboard instruments.

This Garmin 010-11089-00 cable has a length of 2 meters (approximately 6.5 feet).

Yes, this 2-meter cable can be used interchangeably as a backbone cable or as a drop cable within an NMEA 2000 network. Its length makes it versatile for connecting devices far from the main bus or for extending the backbone over short distances.

This cable complies with the NMEA 2000 standard. It is a "plug-and-play" communication standard that succeeded NMEA 0183 for interconnecting marine sensors and displays.

This cable is fitted with NMEA 2000 Micro connectors. These connectors are compatible with the Garmin ecosystem and NMEA 2000-certified equipment from other manufacturers.

The angled connector is particularly advantageous in marine installations where space is limited. It allows you to connect devices with ports that are difficult to access, such as behind multifunction displays, dashboard instruments, or in tight compartments, without exerting excessive strain on the cable or connector.

To connect a device to an NMEA 2000 network, you typically use a T-connector. This cable will connect between the device and the T-connector (as a drop cable), or between two T-connectors to extend the network backbone.

Yes, NMEA 2000 drop cables are limited to a maximum length of 6 meters (20 feet). This 2-meter cable complies with this limitation, making it perfectly suitable for this use.

No, this cable is a backbone/drop cable for data transmission. Powering a NMEA 2000 network must be done via a dedicated NMEA 2000 power cable, which connects to the top of a T-connector and is linked to a 12 Vdc power source.

To shorten a NMEA 2000 cable or create a custom length, you can use Garmin field-installable NMEA 2000 connectors, available in male and female versions. This allows you to adjust the cable length to your specific needs without having to purchase a new cable.

Yes, this cable is fitted with NMEA 2000 Micro connectors and is designed to be compatible with the Garmin ecosystem as well as with NMEA 2000-certified equipment from other manufacturers. The NMEA 2000 standard ensures interoperability between certified devices.

No, this cable is specifically designed for the NMEA 2000 standard, which is the successor to NMEA 0183. The two standards use different protocols and connectors and are not directly compatible without an appropriate protocol converter.

This cable can connect a wide range of NMEA 2000-compatible marine devices, such as sensors (wind, depth, temperature), chartplotters, multifunction displays (MFD), VHF radios, autopilots and other navigation instruments.

NMEA 2000 Micro connectors are designed to be robust and resistant to marine environments. Although the documentation does not specify a precise IP rating for the cable itself, the NMEA 2000 standard ensures reliable connections for use in wet conditions. It is recommended to ensure all connections are properly tightened for optimal protection.

The product reference (SKU) for this cable is 010-11089-00.

Garmin NMEA 2000 cables are designed to be flexible enough to ease installation in various marine environments while remaining robust to withstand stresses and ensure reliable data transmission.

Yes, it is absolutely essential to install terminations (120 ohm resistors) at both ends of the NMEA 2000 backbone to ensure signal integrity and proper network operation. Without appropriate terminations, the network will not function correctly.

The NMEA 2000 network power supply must be connected to the top of a T-connector via a dedicated power cable, not on the sides. The power source must be 12 Vdc and ideally pass through an external switch or the boat's ignition switch.

No, every NMEA 2000 device must be connected to the backbone of the network via a T-connector. The drop cable (like this one) links the device to the T-connector, which is itself integrated into the backbone.

The advantage of the NMEA 2000 "plug-and-play" design is its simple installation and configuration. Compatible devices can be easily added or removed from the network without requiring complex setup, allowing for easy system expansion and maintenance.