Ładowarka Victron Energy Blue Smart IP67 12/17 (1)

This charger delivers an output voltage of 12V and a maximum charging current of 17 amperes in normal mode. It also features a "LOW" mode allowing charging at 6 amperes.

Yes, the Victron Energy Blue Smart IP67 Charger 12/17 (1) has IP67 protection. This means it is fully encapsulated, making it impervious to water, oil, and dust. Its housing is made of die-cast aluminum, and the electronics are potted in resin for maximum durability.

The charger integrates a 5-stage adaptive charging algorithm, managed by a microprocessor. These stages are:

Bulk: Constant current charge.
Absorption: Constant voltage charge to reach full charge.
Reconditioning: To restore deeply discharged batteries.
Float: Maintenance charge.
Storage: Reduced voltage to minimize battery aging.

This charger stands out with a very high energy efficiency of 95%. This high efficiency significantly reduces heat dissipation and power consumption.

Yes, this charger is completely silent. Its design includes no cooling fan or any other moving parts, ensuring noise-free operation.

The charger is equipped with two LEDs for status indication:

The yellow LED indicates the charging state: fast blinking for bulk charge, slow blinking for absorption, solid on for float, and off for storage mode. The green LED indicates the charger is powered on (power on).

Yes, the Victron Energy Blue Smart IP67 Charger 12/17 (1) can be used as a power supply for devices requiring a stable power source.

This charger can operate within a temperature range from -20 °C to +60 °C. It delivers full power up to 40 °C, and the output current is reduced if the temperature exceeds 40 °C without the charger failing, up to 60 °C.

Yes, the charger is protected against overheating. If the ambient temperature rises to 60 °C, the output current will be automatically reduced to prevent charger failure and ensure its longevity.

Once the battery is fully charged, the charger's power consumption is very low, at just 0.5 Watt. This is five to ten times more efficient than the industry standard.

Yes, the Victron Energy Blue Smart IP67 Charger 12/17 (1) includes a temperature-compensated charging function. It measures ambient temperature during the test phase and adjusts the charging voltage accordingly to optimize the process, without requiring special settings for cold or hot environments.

The "storage" mode activates if the battery has not undergone discharge for 24 hours. In this mode, the float voltage is reduced to 13.2 V for a 12 V battery to minimize gassing and corrosion of the positive plates. Once per week, the voltage is increased to the absorption level to "equalize" the battery, preventing electrolyte stratification and sulfation.

This charger is compatible with lead-acid batteries (including gel, AGM and flooded types) and Li-ion (Lithium-ion) batteries.

The charger is designed to charge lead-acid and Li-ion batteries with a capacity between 14 Ah and 225 Ah.

Yes, this charger can initiate charging even if the battery has been discharged to zero volts. It will attempt to recharge a fully discharged battery with a low current and will resume normal charging once sufficient voltage is established at the battery terminals.

Yes, the Victron Energy Blue Smart IP67 Charger 12/17 (1) can reconnect to a fully discharged Li-ion battery that has an internal disconnect function.

A Battery Management System (BMS) may be required to charge a Li-ion battery, depending on the specifications and requirements of the Li-ion battery itself. It is always recommended to consult the manufacturer's instructions for your Li-ion battery.

The charger must be installed in a well-ventilated area near the battery. It should not be placed directly above the battery due to the battery’s potentially corrosive gases.

To connect the charger to the battery, use the supplied ring terminals. Connect the black wire (negative) to the battery’s negative terminal (–) and the red wire (positive) to the battery’s positive terminal (+). Ensure the AC power cable is plugged into the wall outlet only after all DC connections have been made.