ECLIPSE SL100, bandă luminoasă, 5 m

The Garmin ECLIPSE SL100 is a flexible 5-meter LED light strip designed specifically for decorative and indirect marine lighting. It creates a mood on board by discreetly integrating under gunwales, furniture, or behind ceiling panels, offering an alternative to direct light sources.

The Garmin ECLIPSE SL100 light strip is supplied in a 5-metre length.

Yes, the Garmin ECLIPSE SL100 LED strip is fully encapsulated and has an IP68 rating, ensuring complete resistance to water and dust. It can be installed in damp areas but is not designed for permanent submersion.

Yes, the ECLIPSE SL100 LED strip is designed to be installed both indoors and outdoors. It is made from UV-resistant material. However, it is recommended not to install it in areas exposed to direct sunlight.

The Garmin ECLIPSE SL100 light bar has a width of approximately 10.8 mm and a thickness of approximately 5.2 mm.

The typical power consumption of the ECLIPSE SL100 LED strip is approximately 5 watts per meter and per channel. The typical current draw is approximately 0.41 amperes at 12V per meter.

The ECLIPSE SL100 LED light bar is designed to operate with 12V boats only. It can function within a DC voltage range of 10 to 15 volts. It is critical not to connect it to voltages outside this range or directly to an AC power source.

Yes, the Garmin ECLIPSE SL100 LED strip is made from UV-resistant material, ensuring durability in a marine environment.

The SL100 strip is installed using a pre-applied adhesive. For optimal adhesion, thoroughly clean the mounting surface with IPA to remove dust and dirt. Peel off the adhesive backing and press firmly along the edges of the strip (do not apply pressure to the LEDs). Allow the adhesive to cure for 24 hours before turning on the light strip.

Yes, the light strip can be cut to the desired length. It is imperative to cut only at the marked cut points, using a pair of scissors and a single cutting motion at the center of the cut tabs. After cutting, the end must be prepared and sealed to maintain waterproofing.

During handling, do not let the light strip fall or twist. Carefully unroll it from the reel. Do not apply pressure on the strip at the LED level, only on the edges. Do not pull, stretch, twist, or bend the strip on the horizontal axis. For lengths over one meter, it is recommended to use two people for installation.

The ECLIPSE SL100 LED light strip has flexibility allowing a minimum bending radius of 50 mm on the vertical axis. It is important not to bend it on the horizontal axis or twist it.

For outdoor installations in wet areas or with tight bends, it is recommended to use mechanical fasteners (mounting clips) in addition to the adhesive layer. These fasteners should be spaced every 250 to 300 mm and/or on either side of a bend, avoiding alignment with the LEDs.

No, although the ECLIPSE SL100 LED strip is fully sealed and can be installed in wet areas thanks to its IP68 rating, it is not designed for continuous submersion in water.

The ECLIPSE SL100 LED light bar is designed to operate exclusively with boats equipped with a 12V electrical system. It can function within a voltage range of 10 to 15V DC.

No, the ECLIPSE SL100 LED light strip must never be connected directly to an alternating current (AC) power source. It is specifically designed for direct current (DC) power between 10 and 15 volts.

A qualified professional should perform the electrical and mechanical installation of the ECLIPSE SL100 LED strip to ensure the product's safety and proper operation.

To seal the cut end, remove 20 mm of the adhesive backing and lightly scrape the adhesive at 10 mm from the end to expose the silicone. Fill the end cap halfway with the provided silicone adhesive, then fit the cap and wipe off any excess adhesive. Allow to cure for 24 hours before handling.

Yes, the ECLIPSE SL100 LED strip can be used in conjunction with an ECLIPSE Command Center for advanced control. For RGB versions (if applicable), the use of a Command Center and optional extension modules is mandatory. It is important not to mix single-color, dual-color, and RGB lights on the same Command Center zone output.

Yes, like most Garmin products, the ECLIPSE SL100 backlight is covered by a manufacturer’s warranty. For the specific terms and conditions of the warranty, please refer to the documentation provided with the product or visit the official Garmin website.