Modul sondor avansat GSD™ 25

The Garmin GSD™ 25 sounder module integrates several advanced technologies for detailed underwater detection. It supports:

Traditional sonar
CHIRP single-channel and dual-channel
SideVü CHIRP technologies
DownVü CHIRP technologies
These combined capabilities provide a complete view of the underwater environment, including structures and fish beneath and beside the vessel.

The Garmin GSD™ 25 delivers an RMS transmit power of 1 kW. This power provides exceptional penetration and resolution for underwater detection.

For superior clarity and better target separation, the GSD™ 25 operates in CHIRP single-channel and dual-channel mode across a wide frequency range from 40 kHz to 250 kHz.

The SideVü and DownVü CHIRP technologies of the GSD™ 25 operate on frequencies of 455/800 kHz and 260/455 kHz. They provide near-photographic images of structures and fish beneath and alongside the vessel.

Yes, the GSD™ 25 is housed in a fully waterproof polycarbonate plastic enclosure. It complies with the IEC 60529 IPX7 waterproofing standard, meaning it is resistant to temporary immersion.

The GSD™ 25 module measures 251 x 66 x 192 mm (9.9 x 2.6 x 7.6 in) and weighs 771 g (1.7 lb).

The GSD™ 25 is designed to operate within an extended temperature range from -15°C to 70°C (5°F to 158°F).

The GSD™ 25 requires a power supply of 10 to 35 Vdc. Its maximum power consumption is 27 W.

The minimum safe distance from a magnetic compass for the GSD™ 25 is 30 cm (11.8 inches).

The LEDs on the GSD™ 25 indicate its operating status:

Green (slow flashing): The depth sounder is connected to a chartplotter and is functioning correctly.
Red (slow flashing): The depth sounder is powered on but not connected or waiting to connect to a chartplotter.
Red/Green (slow flashing): The depth sounder is in test mode.
Red (fast flashing): Indicates a system error; the chartplotter will display a message.
Red (solid): Indicates a hardware failure of the depth sounder.

For installation of the GSD™ 25, you will need the following tools:

A drill and drill bitsA Phillips #2 screwdriverCable ties (optional)Marine sealant (optional)

When selecting the mounting location for the GSD™ 25, consider the following points:

The depth sounder must not be submerged.The location must provide adequate ventilation and avoid exposure to extreme temperatures.The depth sounder LEDs must be visible.Power and network cables must be easy to connect.The transducer cable must be connectable.

Yes, if you mount the bracket on fiberglass with screws, it is recommended to use a countersink drill bit to drill a pilot hole only through the top gelcoat layer. This helps prevent any cracking of the gelcoat when tightening the screws. Additionally, Garmin recommends applying anti-seize lubricant on stainless steel screws before installation to prevent them from seizing.

To connect the GSD™ 25 to the Garmin marine network:

If your boat is equipped with a GMS™ 10 network port expander, connect the network cable to an available port on the GMS 10.
If your boat is not equipped with a GMS™ 10 network port expander, connect the network cable directly to the network port of your chartplotter.
Ensure the notches are properly aligned and the locking collars are tightened.

To connect the power cable of the GSD™ 25:

Connect the stripped end of the power cable to a 12 Vdc power source and to ground. Align the notch at the end of the power cable with the device's power port and insert the cable. Tighten the locking ring. Important: Do not remove the inline fuse holder. The appropriate fuse (4.0 A) must be in place to prevent risk of injury or damage to the product.

General steps for installing the GSD™ 25 are as follows:

Select a suitable mounting location.Physically mount the fishfinder by marking pilot holes, drilling, and securing the unit.Connect the fishfinder to the Garmin marine network and power supply.Connect the fishfinder to the transducer.Careful planning and necessary precautions are essential, especially when drilling.

The Garmin GSD™ 25 is an advanced fishfinder solution designed for Garmin marine navigation systems. It connects via the Garmin marine network, typically to a compatible chartplotter for data display.

The GSD™ 25 is compatible with a variety of Garmin transducers supporting its different technologies and frequencies. It supports transducers for:

Traditional sonar (50/77/83 kHz)CHIRP single-channel and dual-channel (40 kHz to 250 kHz)SideVü and DownVü CHIRP (455/800 kHz and 260/455 kHz)The choice of transducer will depend on the frequencies and technologies you wish to use.