Pachet vânt fără fir (GNX™ Wind + gWind™ Wireless 2)

To install the gWind™ Wireless 2 sensor, follow these steps:

Install the supplied battery in the sensor by opening the compartment with a #2 Phillips screwdriver.Choose a mounting location on the masthead that is a horizontal surface. If necessary, add a shim to create a flat surface.The sensor must be installed facing the bow of the boat, parallel to the centerline.Use the mounting bracket as a template to mark and drill pilot holes (4.5 mm / 11/64 in).Secure the mounting bracket with the included screws.Place the sensor in the bracket, tighten the locking nut, and attach the safety clamp.If the sensor is not mounted exactly facing forward, you can adjust its orientation via the GNX™ Wind display.

Yes, the gWind™ Wireless 2 sensor comes with a battery included in the pack. You must install it before mounting the device.

To maintain battery charge, it is recommended to store the sensor in a location exposed to light when not in use. If the sensor is stored in a dark place for an extended period, it is advisable to replace the battery at the start of each season to ensure optimal operation.

The GNX™ Wind display is designed for flush mounting. Here are the main steps:

Choose a location on a flat mounting surface, sturdy enough to support the unit and at least 209 mm (8.2 in) from a magnetic compass.Use the supplied flush-mount template to mark the cutout and pilot holes.Cut the mounting hole (90 mm / 3.5 in) and drill pilot holes (2.8 mm / 7/64 in). If drilling into fiberglass, use a countersink bit to prevent cracking.Place the supplied gasket on the back of the unit and apply marine sealant around the gasket to prevent leaks.Connect all required cables (NMEA 2000®) before inserting the unit into the cutout if access will be restricted later.Insert the instrument into the cutout and secure it firmly with the supplied screws. Apply anti-seize lubricant to stainless-steel screws if mounting into fiberglass.Snap the bezel into place.

Yes, absolutely. The Garmin wireless wind pack is designed to integrate easily into an existing NMEA 2000® network. The GNX™ Wind display connects directly to the NMEA 2000® network, which provides power and data from other compatible devices. The gWind™ Wireless 2 sensor communicates wirelessly with the GNX™ Wind display, and the data is then transmitted via the NMEA 2000® network. The necessary NMEA 2000® cables and connectors are included in the pack.

The two components of the pack offer good water resistance:

The gWind™ Wireless 2 sensor has an IEC 60529 IPX-6 water resistance rating, meaning it is protected against heavy seas. The GNX™ Wind display has an IEC 60529 IPX7 rating, indicating it can withstand accidental immersion in water up to 1 meter for 30 minutes.

The operating temperature ranges for the pack components are as follows:

The gWind™ Wireless 2 sensor can operate within a temperature range of -20°C to 50°C (-4°F to 122°F). The GNX™ Wind display is designed to operate within a temperature range of -15°C to 70°C (5°F to 158°F).

Yes, if the gWind™ Wireless 2 sensor and the GNX™ Wind display are purchased together as part of this bundle, they are usually pre-paired at the factory. No additional action is required from you for the initial pairing. If the sensor was purchased separately or if you wish to use it with another compatible Garmin device, you will need to follow the wireless pairing instructions in the user manual of the compatible device.

The Garmin wireless wind pack includes:

GNX™ Wind display gWind™ Wireless 2 sensor Mounting bracket Necessary screws NMEA 2000® cables for integration into your boat's network.

The gWind™ Wireless 2 sensor is a wireless anemometer and wind vane that accurately measures wind speed and direction. It is designed to be mast-top mounted and wirelessly transmits data to the GNX™ Wind display.

The gWind™ Wireless 2 sensor must be mounted on a horizontal surface at the masthead, facing forward and parallel to the boat's centerline. If alignment is not perfect, you can configure it via the GNX™ Wind display for accurate data.

No, one of the main advantages of the Garmin wireless wind pack is its easy installation. The gWind™ Wireless 2 sensor communicates wirelessly with the GNX™ Wind display, eliminating the need for complex wiring through the mast, unlike traditional wired systems.

Yes, the system integrates via the NMEA 2000® network. The GNX™ Wind display connects to the NMEA 2000 network for power and data reception. The necessary NMEA 2000 cables and connectors are included to facilitate connection to an existing network or the creation of a basic network.

The GNX™ Wind display cannot directly receive NMEA 0183 data. However, it can display NMEA 0183 data from sources connected to a GNX 20 or GNX 21 device (sold separately) on the same NMEA 2000 network.

The gWind™ Wireless 2 sensor can measure wind speeds from 0.9 to 90 knots (0.5 to 50 meters per second).

The gWind™ Wireless 2 sensor has an IEC 60529 IPX-6 water resistance rating, meaning it is protected against heavy seas. The GNX™ Wind display is rated IEC 60529 IPX7, allowing it to withstand accidental immersion up to 1 meter for 30 minutes.

The gWind™ Wireless 2 sensor is powered by an included battery. To maintain battery charge, it is best to store it in a location exposed to light. If the sensor is stored in a dark place, it is recommended to replace the battery at the start of each season.

When installing the GNX™ Wind display, choose a flat and sufficiently rigid mounting surface to support the device's weight. Ensure there is enough space behind the surface for cable routing and connections. The device must be mounted at a safe distance of 209 mm from a magnetic compass to prevent interference.

The GNX™ Wind display has a maximum power consumption of 1.35 W. It is powered via the NMEA 2000 network, with an NMEA 2000 input voltage range of 9 to 16 Vdc.

For maintenance of the gWind™ Wireless 2 sensor, use a mild soap solution to clean it, then rinse with water. Do not use detergents or high-pressure water. If the sensor will not be used for extended periods, it is also recommended to remove it and store it in a dry place.