Invertor 12/3000 Smart

The Victron Energy Inverter 12/3000 Smart inverter provides a continuous output power of 3000 VA (i.e., 2400 W) when operating at an ambient temperature of 25°C. It can also handle a peak power of 6000 W for starting demanding loads.

The Victron Energy Inverter 12/3000 Smart inverter requires an input DC voltage between 9.3 V and 17 V to operate correctly. It is specifically designed for 12 V battery systems.

The inverter generates an AC output voltage of 230 VAC with a tolerance of ±2%. The output frequency is configurable and can be set to 50 Hz or 60 Hz, depending on your specific requirements.

This inverter produces a pure sine wave. This feature is essential for powering sensitive electronic equipment and household appliances, ensuring stable operation without interference.

The Inverter 12/3000 Smart inverter includes Bluetooth functionality. You can configure and monitor it easily using the VictronConnect app, available on your smartphone or tablet.

The VE.Direct communication port allows connecting the inverter to a computer via a VE.Direct to USB interface cable, or to a GX monitoring device such as the Cerbo GX. This provides comprehensive system management and monitoring.

The ECO mode allows the inverter to switch to standby when the connected load drops below a preset value (minimum 15 W). The inverter then briefly powers back on at regular intervals (default every 2.5 seconds, adjustable) to check if the load has increased. If it detects a load above the set threshold, it remains on.

The inverter is equipped with multiple protections to ensure its reliability and the safety of your installation. These include protections against:

Output short-circuitsOverloadsBattery voltages too high or too lowOverheatingPresence of AC voltage at the outputHigh DC ripple

For optimal performance, the inverter must be installed on a flat surface. It is important to avoid any contact with water, direct exposure to sunlight, and to ensure that the ambient temperature is between -20°C and 40°C. Leave at least 10 cm of free space around the device for adequate ventilation.

The Victron Energy Inverter 12/3000 Smart can operate within an ambient temperature range of -40°C to +65°C. However, power derating applies above 40°C to maintain performance and reliability.

For optimal connection to a 12V battery, it is recommended to use DC cables with a 70 mm² cross-section for lengths up to 1.5 meters, and 95 mm² for lengths between 1.5 and 3 meters. The inverter connection terminals are M8 type.

To protect the Victron Energy Inverter 12/3000 Smart inverter in a 12V system, it is strongly recommended to install a 400A DC fuse close to the battery.

The inverter is a Safety Class I product, which means the chassis must be earthed. An earth point is located outside the product. The earth conductor must have at least half the cross-section of the conductors used for the battery connection.

Yes, the 12/3000 Smart inverter has a high starting power capacity (peak power of 6000 W). This allows it to start inductive loads such as power tools, LED lamp converters, or other devices requiring a high inrush current.

You can configure multiple inverter parameters, including:

Low battery voltage alarm and cutoff levelsOutput voltage and frequency (210-245 V, 50/60 Hz)ECO mode settings (activation/deactivation and detection level)

Yes, the inverter is equipped with a connector for remote on/off control. An external switch can be connected to this two-pole connector, or between the battery positive terminal and the left contact of the connector, which is useful for automotive applications, for example.

Yes, the Victron Energy Inverter 12/3000 Smart inverter is designed for marine and mobile environments. Its robustness, toroidal transformer topology, and built-in protections make it a reliable solution for providing AC power onboard.

The Victron Energy Inverter 12/3000 Smart inverter delivers a maximum efficiency of 93%. High efficiency means less energy loss as heat and more efficient use of your battery power.

Yes, thanks to its VE.Direct port, the inverter can be connected to GX monitoring devices such as the Cerbo GX. This allows full integration into a Victron energy management system, providing centralized monitoring and control.