Adaptér kabel 4pin samice / 5pin samec NMEA 2000®

This adapter cable is designed to connect specific Garmin devices, featuring a 4-pin female connector, to a standard NMEA 2000® network using a 5-pin male connector. It enables the integration of these devices into the network and the exchange of marine data.

The Garmin adapter cable 010-12445-10 has a length of 2 meters, which corresponds to approximately 6 feet.

This cable is specifically compatible with Garmin echoMAP™ CHIRP 5-inch and ECHOMAP Plus chartplotter/fishfinder units. It is designed for these models to interface with a NMEA 2000® network.

No, this is not a standard NMEA 2000® cable like a Backbone or Drop cable. It is a specific adapter cable that converts a 4-pin Garmin connector into a 5-pin male NMEA 2000® connector.

Some Garmin devices, particularly the echoMAP™ CHIRP 5-inch and ECHOMAP Plus series, use a 4-pin pinout for their data port. The NMEA 2000® network uses a 5-pin standard. This adapter cable bridges this pinout difference, enabling connection and communication between your Garmin device and the NMEA 2000® network.

Yes, if your chartplotter is a compatible model (echoMAP™ CHIRP 5-inch or ECHOMAP Plus) and you want to connect it to an NMEA 2000® network that already has sensors connected, this cable will enable data exchange between your chartplotter and those sensors via the network.

For installation, connect the 4-pin female end of the cable to your compatible Garmin device (echoMAP™ CHIRP 5-inch chartplotter or ECHOMAP Plus). Then, connect the 5-pin male end of the cable to an available port on your existing NMEA 2000® network.

Yes, once connected via this adapter cable, your Garmin device will be able to exchange data with other instruments connected to the NMEA 2000® network. This includes receiving and sending information supported by the NMEA 2000® protocol.

No, this adapter cable is specifically designed for 5-inch echoMAP™ CHIRP chartplotter/fishfinder combos and ECHOMAP Plus combos. It is not suitable for the GPSMAP® series.

Yes, once this adapter cable is connected to your Garmin device and features the 5-pin male NMEA 2000® connector, you can connect it to a standard NMEA 2000® cable (such as a drop cable or T-connector) to integrate it into your network and extend it if needed.

Yes, like all Garmin marine connectivity accessories, this cable is designed to withstand typical marine environmental conditions, including humidity and temperature variations, ensuring a reliable connection.

This cable is specifically listed as compatible with 5-inch echoMAP™ CHIRP chartplotter/fishfinder combos and ECHOMAP Plus combos. Compatibility with older echoMAP™ models (non-CHIRP or non-Plus) is not guaranteed by this specification.

The 4-pin female end of the cable plugs into the corresponding data port (usually a transducer or communication port) of compatible Garmin devices, such as the 5-inch echoMAP™ CHIRP chartplotter/fishfinders and ECHOMAP Plus models.

Yes, the reference number 010-12445-10 indicates that this is a genuine Garmin adapter cable, designed and manufactured by Garmin for its marine equipment.

No, the primary function of this cable is to adapt a specific Garmin device to a NMEA 2000® network. It is not designed for a direct point-to-point connection between two Garmin devices without the NMEA 2000® network as an intermediary.

NMEA 2000® is a standardized communication protocol used in marine electronic systems. It allows different devices (chartplotters, depth sounders, radars, engines, sensors) to share data over a single network, simplifying integration and data exchange.

Once the cable is physically connected, your Garmin device should detect the NMEA 2000® network and connected devices. Settings may be required in your chartplotter’s menus to display or use specific data from the network, but the physical connection via the cable does not require complex software configuration specific to the adapter.

This cable is specifically designed to adapt certain Garmin devices (with a 4-pin connector) to a NMEA 2000® network. While the NMEA 2000® network is an inter-brand standard, the 4-pin end is proprietary to Garmin and will not work with devices from other brands.

Garmin NMEA 2000® cables, including this adapter, are typically designed with adequate shielding to minimize electromagnetic interference common in a marine environment, ensuring reliable data transmission.

The 5-pin male connector is the standard NMEA 2000® interface. It allows you to connect the cable directly to a T-connector or another connection point on an existing NMEA 2000® network, thereby integrating the Garmin device into the network.