SmartPump v2 pro autopilota Reactor™

The Garmin SmartPump v2 (part number 010-00705-62) is a self-contained hydraulic pump designed for Garmin Reactor™ autopilot systems, specifically for boats with hydraulic steering. It simplifies selection with its "one-size-fits-most" design that covers most hydraulic cylinder applications and volumes.

The SmartPump v2 integrates a brushless motor. This advanced technology provides increased reliability and extended lifespan compared to traditional brushed motors.

The brushless motor of the SmartPump v2 offers several advantages, including increased reliability, extended lifespan, reduced power consumption (less than 1 A in standby, 5-10 A in operation, 34 A at peak) and quieter operation. Its compact design and improved thermal performance make it a discreet and efficient solution.

Yes, the design of the SmartPump v2 eliminates the risk of rudder lock at the stop, which is an advantage in terms of safety.

Yes, the electronic control unit (ECU) of the SmartPump v2 is fully waterproof, contributing to its robustness and durability in a marine environment.

This pump is designed for use exclusively with Garmin Reactor™ autopilot systems. Using it with any other system may damage the autopilot, the pump, or the boat.

Yes, the SmartPump v2 can be used with Mercury Verado engines, but this requires installing additional components provided in a specific adapter kit (Mercury Verado Reactor™ adapter kit).

The pump must be installed with a steering system equipped with a vented reservoir. Installing it with a non-vented reservoir would damage the pump. The vent hole is usually located in the filler cap of the highest helm station. It is imperative to check the reservoir ventilation before installation.

For all hydraulic connections, including the return line, it is recommended to use hoses of -4 [6 mm (1/4 in) internal diameter] or larger, with machine-crimped or field-replaceable fittings rated for a minimum pressure of 1000 psi.

The autopilot system, including the SmartPump v2, must be installed by a qualified marine installer. Specific knowledge of marine steering and electrical systems is required for correct installation.

The pump must be installed in a dry location, protected from water and harsh weather. For installations with larger steering cylinders or requiring higher fluid pressure, it is recommended to install the pump as close as possible to the cylinder, ideally with no more than 3 meters (10 feet) of hydraulic hose connecting it to the cylinder.

The pump should preferably be mounted horizontally. If vertical mounting is necessary, the pump must be installed with the connectors on the pump head facing upward.

The required tools include:

Safety glassesDrill and bitsWrenchesTorque wrench (if configuring for an unbalanced steering ram)Wire cutters/strippersPhillips and flathead screwdriversCable tiesMarine corrosion inhibitor sprayMounting screws (the kit includes screws, but suitable screws for the mounting surface may be required)Hydraulic system hardware (hoses, T-fittings, shut-off valves, thread sealant such as Loctite 567, bleeding equipment, hydraulic fluid)

For hydraulic fittings without an O-ring, a liquid sealant such as Loctite 567 must be used. It is imperative not to use thread seal tape (such as Teflon tape) or paste sealant on any hydraulic fitting in this system, as small debris could enter the hydraulic system, get stuck in the valves, and render the autopilot or steering system inoperative.

Yes, it is recommended to use T-fittings (not included) to connect the hydraulic lines to the pump. It is also advisable to install shut-off valves (not included) in the hydraulic lines between the pump manifold and the T-fittings. This method allows easy isolation and removal of the pump for maintenance while maintaining normal boat operation.

Yes, it is essential to bleed all air from every part of the hydraulic system before attempting to use the autopilot to steer the boat. Do not attempt to use the autopilot until all air has been bled.

After completing the autopilot installation, it is recommended to update the software before proceeding with the configuration process. If the system is connected to a Garmin chartplotter via an NMEA 2000 network, the update can be performed via the chartplotter. If not, an NMEA 2000 Network Updater (sold separately) is required.

If the boat is equipped with an unbalanced rudder cylinder, the pump must be specifically reconfigured for this situation. This reconfiguration also affects the pump's check valves.

In a Mercury Verado system, the low-pressure return line must be routed from the helm (helm only for single-helm installations) to the Mercury pump module, then connected to the SmartPump. A T-fitting and hose clamps are used for this connection, and a threaded fitting is screwed into the SmartPump to accept the return hose.

Yes, using sealing tape (such as Teflon tape) or paste sealant on any hydraulic connection in this system voids the warranty. Small debris from these materials can enter the hydraulic system, jam in the valves, and render the autopilot or steering system inoperative.