Převodník DC Master 48/12-20

The Mastervolt DC Master 48/12-20 is a non-isolated converter. This means there is no galvanic isolation between the 48V input and the 12V output. In a non-isolated converter, the negative grounds of the input and output are common.

This makes it suitable for installations where the 48V circuit and the 12V circuit share the same negative ground. In contrast, an isolated converter (such as certain models in the DC Master range marked 'isolated') electrically separates the two circuits, which may be necessary to avoid ground loops or for safety reasons with sensitive equipment.

Yes, this is perfectly possible. The Mastervolt DC Master 48/12-20 is designed to convert an input voltage of 48V into a stabilized output voltage of 13.6V. This 13.6V output is ideal for maintaining the charge of a 12V battery (lead-acid, AGM or gel type) or for directly powering 12V consumers.

It can therefore perfectly serve to recharge a 12V auxiliary battery from a 48V propulsion battery bank, for example on a sailboat or an electric boat.

Installing the DC Master 48/12-20 requires a few essential precautions:

Power off: Ensure the power source (48V battery) is switched off or disconnected before starting installation.Disconnect loads: Verify no devices are connected to the batteries during installation to prevent any risk.Check voltages: Confirm the battery voltage matches the converter's input voltage (48V) and the output voltage (13.6V) is suitable for your load.Install a fuse: Add a fuse on the positive cable, as close as possible to the 48V battery.Mounting: Choose a cool, dry, and ventilated location. Use the provided mounting bracket to clip the converter in place.Wiring order: Connect the input wires (48V side) first, then the output wires (12V side).

The Mastervolt DC Master 48/12-20 can supply a continuous output current of 20A. It can also deliver a peak current of 24A for a maximum duration of 2 minutes, which is useful for starting equipment with high current draw.

The rated output power of the Mastervolt DC Master 48/12-20 is 272W. This corresponds to an output voltage of 13.6V multiplied by a continuous current of 20A. Its maximum output power reaches 326W (13.6V x 24A for 2 minutes).

Absolutely. The Mastervolt DC Master 48/12-20 is specifically designed for this type of application. On modern cruising sailboats or electric-powered boats, it is common to have a 48V service battery bank. This converter reliably and stably powers all your 12V equipment (lighting, autopilot, navigation instruments, VHF, etc.) from this 48V source.

The Mastervolt DC Master 48/12-20 accepts an input voltage range of 40 to 62V to deliver its full output power. It can withstand without damage an input voltage range of 0 to 65V DC. Below 40V or above 62V, the output may no longer be stabilized or the converter could go into safety mode.

The Mastervolt DC Master 48/12-20’s input and output connections are Faston type (quick-connect terminals). This makes cable connections easier. The product comes with the required Faston connectors.

Yes, the Mastervolt DC Master 48/12-20 is a regulated DC-DC converter. This means its 13.6V output voltage remains stable and precise even if the input voltage fluctuates within its normal operating range (40–62V). This regulation is essential to protect sensitive electronic equipment connected to the output.

Yes, absolutely. The Mastervolt DC Master 48/12-20 is perfectly suited to power a 12V autopilot. Its stabilized output voltage of 13.6V and ability to provide up to 20A continuously (and 24A peak) suit most autopilots, which often draw significant current during harbour manoeuvres. Just ensure your autopilot’s consumption does not exceed 20A continuously.

The Mastervolt DC Master 48/12-20 is supplied complete with everything needed for installation. The package includes:

The DC-DC converter itselfA mounting bracket (clip) for easy wall installationMounting screws for the bracketFaston connectors for cable connection

Yes, the Mastervolt DC Master 48/12-20 is compatible with 48V lithium batteries, provided the battery voltage remains within the converter's operating range (40-62V). Since lithium batteries have a wider voltage range than lead-acid batteries, it is important to verify that the maximum charge voltage of your lithium battery does not exceed 62V. In most cases, this is compatible.

Yes, the Mastervolt DC Master 48/12-20 can power a 12V refrigerator. Most marine refrigerators draw between 3 and 8A during operation, with a startup surge when the compressor kicks in. With 20A continuous and 24A peak output, this converter can handle this type of load without issues. Ensure the total power draw of connected devices does not exceed 272W.

The Mastervolt DC Master 48/12-20 is easy to install thanks to the supplied bracket. Here is the procedure:

Choose a cool, dry, and well-ventilated location.Use the mounting bracket to mark the positions for the three mounting holes.Drill 3.5 mm diameter holes.Fix the bracket using the supplied screws.Snap the converter onto the bracket.Ensure sufficient clearance around the unit for proper airflow and natural cooling.

The Mastervolt DC Master 48/12-20 part number (SKU) is 81400800. This code uniquely identifies the item within the Mastervolt range and ensures the correct reference is ordered.