Blue Smart IP67 nabíječka 12/17 (1)

This charger delivers a 12V voltage and a maximum charging current of 17 amperes in normal mode. It also features a "LOW" mode allowing charging at 6 amperes.

Yes, the Victron Energy Blue Smart IP67 Charger 12/17 (1) has IP67 protection. This means it is fully encapsulated, making it impervious to water, oil, and dust. Its housing is made of die-cast aluminum, and the electronics are potted in resin for maximum robustness.

The charger integrates a 5-stage adaptive charging algorithm managed by a microprocessor. These stages are:

Bulk: Constant-current charging.
Absorption: Constant-voltage charging to reach full charge.
Reconditioning: For restoring deeply discharged batteries.
Float: Float charging to maintain charge.
Storage: Reduced voltage to minimize battery aging.

This charger stands out with a very high energy efficiency of 95%. This high efficiency significantly reduces heat dissipation and power consumption.

Yes, this charger is completely silent. Its design has no cooling fan or any other moving parts, ensuring noise-free operation.

The charger is equipped with two LEDs for status indication:

The yellow LED indicates the charge state: fast blinking for bulk charge, slow blinking for absorption, solid on for float, and off for storage mode. The green LED indicates that the charger is powered on (power on).

Yes, the Victron Energy Blue Smart IP67 Charger 12/17 (1) can be used as a power supply for devices requiring a stable current source.

This charger can operate within a temperature range from -20 °C to +60 °C. It delivers full power up to 40 °C, and the output current is reduced if the temperature exceeds 40 °C without the charger failing, up to 60 °C.

Yes, the charger is protected against overheating. If the ambient temperature rises to 60 °C, the output current will be automatically reduced to prevent charger failure and ensure its longevity.

Once the battery is fully charged, the charger's power consumption is very low, at just 0.5 Watt. This is five to ten times more efficient than the industrial standard.

Yes, the Victron Energy Blue Smart IP67 Charger 12/17 (1) includes a temperature-compensated charging function. It measures ambient temperature during the test phase and adjusts the charging voltage accordingly to optimize the process, without requiring special settings for cold or hot environments.

The "storage" mode activates if the battery has not undergone discharge for 24 hours. In this mode, the float voltage is reduced to 13.2 V for a 12 V battery to minimize gassing and positive plate corrosion. Once per week, the voltage is increased to the absorption level to "equalize" the battery, thus preventing electrolyte stratification and sulfation.

This charger is compatible with lead-acid batteries (including gel, AGM, and flooded batteries) and Li-ion (Lithium-ion) batteries.

The charger is designed to charge lead-acid and Li-ion batteries with a capacity between 14 Ah and 225 Ah.

Yes, this charger can initiate charging even if the battery has been discharged to 0 volts. It will attempt to recharge a completely dead battery with a low current and resume normal charging once sufficient voltage is established at the battery terminals.

Yes, the Victron Energy Blue Smart IP67 Charger 12/17 (1) is capable of reconnecting to a fully discharged Li-ion battery that has an internal disconnect function.

A Battery Management System (BMS) may be required to charge a Li-ion battery, depending on the specifications and requirements of the Li-ion battery itself. It is always recommended to consult the manufacturer's instructions for your Li-ion battery.

The charger must be installed in a well-ventilated area near the battery. It should not be placed directly above the battery due to potential corrosive gases emitted by the battery.

To connect the charger to the battery, use the supplied ring terminals. Connect the black cable (negative) to the battery’s negative terminal (–) and the red cable (positive) to the battery’s positive terminal (+). Ensure the AC power cable is plugged into the wall outlet only after all DC connections are made.