Lynx rozvodník 1000 DC M8

The Lynx 1000 DC M8 distributor is a key component of Victron Energy's modular Lynx busbar system. It integrates a positive busbar and a negative busbar. The positive section provides four connections protected by MEGA fuses (to be purchased separately) with a fuse status monitoring function. The negative section has four connections and one ground connection, all with M8 terminals.

The Lynx distributor provides four positive connections protected by fuses and four negative connections. It also features a separate ground connection.

The Lynx M8 fuse block is designed to accommodate MEGA-type fuses. These fuses must be purchased separately as they are not included with the fuse block.

No, the Lynx distributor is designed to accept MEGA fuses, but these must be purchased separately and are not included with the module.

The Lynx distributor comes with a 40 cm RJ10 cable. This cable is used to power the Lynx distributor and also to transmit data, including fuse status, when connected to a Lynx Smart BMS.

The Lynx distributor has four LEDs indicating the state of the fuses, one for each positive connection. It monitors each fuse and will detect if a fuse is blown, signaling the state via these LEDs.

The M8 or M10 designation refers to the busbar connection joints where Lynx modules are interconnected. The specific product, the Lynx 1000 DC M8 Power Distribution Unit, uses M8 busbar connections. The fuses and cable connections on this distributor are also always M8.

Yes, the Lynx distributor's negative bus bar has a dedicated ground connection, in addition to the four standard negative connections.

The Lynx distributor is part of a DC distribution system that typically supports system voltages of 12 V, 24 V or 48 V. The supported battery voltage range for associated components such as the Lynx Smart BMS is 9 to 60 VDC.

The Lynx distributor is an essential solution for protecting and managing DC circuits within the Lynx modular distribution system. It allows distributing DC power to multiple devices while individually protecting each circuit with fuses and monitoring their status.

Yes, the Lynx distributor is fully compatible with the Lynx Smart BMS. When connected to a Lynx Smart BMS, up to four Lynx distributors can send information about the status of their fuses to the BMS. This data is then accessible via the VictronConnect app or a GX device.

Yes, if the Lynx distributor is connected to a Lynx Smart BMS, you can monitor the status of its fuses via a GX device (such as a Cerbo GX). This allows for local or remote monitoring via the VRM portal.

Yes, if the Lynx distributor is connected to a Lynx Smart BMS, it can be monitored and configured using the VictronConnect app on your smartphone or tablet.

No, the fuse status monitoring function of the Lynx distributor is not available if the distributor is connected to a Lynx Shunt VE.Can. This function is specifically enabled when connected to a Lynx Smart BMS.

Up to four Lynx distributors can be connected to a Lynx Smart BMS to send data about the status of their fuses and enable their monitoring.

Yes, the Lynx distributor can be used alone to provide a fused DC distribution. However, to benefit from advanced fuse monitoring via the VictronConnect app or a GX device, it must be connected to a Lynx Smart BMS.

Before working on the Lynx distribution system, it is crucial to ensure that the busbars are not live. Disconnect all positive battery terminals before removing the Lynx front cover. Only qualified technicians should work on batteries, following the safety warnings indicated in the battery manual.

The Lynx modules are designed to be mechanically interconnected via their busbars. They can be mounted side by side to form a compact and modular distribution system. The Lynx M8 distributor uses M8 busbar connection joints for this interconnection.

To connect the DC cables to the Lynx distributor:

The positive cables are connected to the four positive terminals protected by fuses. The negative cables are connected to the four negative terminals. A dedicated grounding connection is also available. All these connections use M8 terminals.

The Victron Energy Lynx 1000 DC M8 distributor is a key component of the modular Lynx busbar system, designed for DC electrical distribution.

It integrates a positive busbar and a negative busbar:

The positive busbar features four connections protected by MEGA fuses (sold separately). These connections include a fuse status monitoring function. The negative busbar offers four connections for equipment and one ground connection. This module comes with a 40 cm RJ10 cable for power supply and data transmission. When connected to a Lynx Smart BMS, the distributor can send information about the status of its fuses. This data is accessible via the VictronConnect app or a GX device (such as a Cerbo GX), enabling local or remote monitoring via the VRM portal. Note that this monitoring feature is not available if the distributor is connected to a Lynx Shunt VE.Can.

The Lynx distribution system, of which this distributor is part, is designed for a nominal capacity of 1000 A. This specific model uses M8 connections for fuses and cables.