Střídač Phoenix VE.Direct Schuko 48V/800W

The Victron Energy VE.Direct Schuko* inverter provides a continuous output power of 800W at an ambient temperature of 25°C. This power is 650W at 40°C.

This inverter is equipped with an AC output socket of the Schuko type (CEE 7/4), compatible with European standards.

The Victron Energy VE.Direct Schuko* inverter requires a 48V DC input voltage. The supported input voltage range is 36.8V to 62V.

Yes, this inverter is designed to handle high startup loads. It can provide a peak power of 1200W for 15 seconds. This capacity is useful for starting equipment such as LED lamp converters, halogen lamps, or certain power tools.

The ECO mode reduces the inverter's no-load power consumption. When the connected load drops below a predefined value (minimum 15W), the inverter switches to standby mode. It then briefly reactivates (by default every 2.5 seconds) to check if the load has increased. If the load exceeds the predefined level, the inverter remains powered on. In ECO mode, the default no-load consumption is 2W.

The inverter integrates multiple protections to ensure safe and reliable operation:

Output short-circuit protectionOverload protectionProtection against excessively high battery voltagesProtection against excessively low battery voltagesProtection against excessively high temperatures (overload or high ambient temperature)Protection against excessive DC ripple

Yes, the inverter is fully configurable via its VE.Direct communication port. You can connect it to a computer (using a VE.Direct to USB interface cable) or to smartphones and tablets (using a VE.Direct Bluetooth Smart dongle).

Via the VE.Direct port, you can configure several parameters, including:

Battery low voltage alarm and reset thresholdsBattery low voltage cut-off and restart thresholds (or dynamic load-dependent cut-off)AC output voltage (adjustable from 210V to 230V)Output frequency (50 Hz or 60 Hz)ECO mode activation/deactivation and its detection level

The inverter can operate within an ambient temperature range from -40°C to +65°C. It is equipped with a fan-assisted cooling system. Above 40°C, the output power is reduced by 1.25% per additional degree Celsius.

The Victron Energy VE.Direct Schuko* inverter (model 48V/800W) has a maximum efficiency of 91%.

In normal mode (no load), the idle power consumption of the 48V/800W inverter is 9W. In default ECO mode, idle power consumption is 2W.

For optimal performance, the inverter must be placed on a flat surface. It is recommended to install it at the base or on a vertical wall with the fan at the bottom. Avoid direct exposure to sunlight, humidity, dust, and environments with explosion risks. Ensure there is at least 10 centimeters of free space around the device for adequate ventilation.

It is crucial to leave a free space of at least 10 centimeters all around the inverter to ensure sufficient air circulation. Do not block the ventilation vents. If the inverter overheats, it will shut down automatically and restart once a safe operating temperature is reached.

The inverter connects to the battery via screw terminals, requiring no special tools for installation. It is important to use battery cables with sufficient cross-section and a battery of adequate capacity.

Yes, this is a Safety Class I product; the chassis must be grounded. A grounding point is located outside the product. The ground conductor connecting the chassis ground terminal to ground must have at least half the cross-section of the conductors used for the battery connection.

Yes, a remote on/off switch can be connected to a dedicated two-pole connector on the inverter. Alternatively, the left contact of this connector can be linked to the battery positive, which is useful for automotive applications by wiring it to the ignition switch. For the inverter to start, the front switch must also be set to 'On' or 'ECO'.

The VE.Direct communication port allows connecting the inverter to:

A computer, using a VE.Direct to USB interface cable.Smartphones, Apple and Android tablets, and other devices, using a VE.Direct Bluetooth Smart dongle.These connections enable configuration and monitoring of the inverter.

No, you must never connect the AC output of the inverter to another AC source, such as a domestic wall outlet or a generator. The inverter has no AC output fuse, but features a fast current limiter in case of short-circuit and an overload detection mechanism.

The Victron Energy VE.Direct Schuko* inverter has an IP21 protection rating. This means it is protected against solid objects larger than 12.5 mm and against vertically falling water droplets.

The Victron Energy VE.Direct Schuko* inverter offers comprehensive configuration options via its VE.Direct port. This port allows the device to be connected to a computer (requires a VE.Direct to USB interface cable) or to smartphones, tablets, and other devices (requires a VE.Direct Bluetooth Smart dongle).

The following parameters can be adjusted:

Battery low voltage alarm and reset levels: Set thresholds for low battery alerts.Battery low voltage cut-off and restart levels: Configure when the inverter should shut down and restart based on battery voltage.Dynamic cut-off: A load-dependent cut-off level can be set.Output voltage: The AC output voltage can be adjusted between 210 and 245 V.Output frequency: Choose between 50 Hz or 60 Hz.ECO mode: Enable or disable ECO mode and set its detection level. In ECO mode, the inverter goes into standby when the load drops below a predefined value (minimum load: 15W). It briefly restarts (default interval: every 2.5 seconds, adjustable) to check if the load has increased. If the load exceeds the predefined level, the inverter remains on.These configurations optimize inverter operation based on your specific needs and battery system status.