Číslicový multifunkční měřič AC s alarmem

This multifunction digital AC meter is designed to measure and display simultaneously the voltage (Voltage), current (Amperage), frequency (Frequency) and power (Power) of your AC installation. It provides a comprehensive overview of the performance of your electrical system.

The 8247-BSS meter is equipped with alarm features for high voltage, low voltage, and high current. These alarms alert users to potentially hazardous conditions or system malfunctions.

The display integrates adjustable brightness and a scan mode function for easy reading of data. It has three brightness levels.

Yes, on three-button models such as the 8247, the arrow buttons allow you to cycle through the display between volts, amperes, hertz (frequency), and watts (power).

Monitoring voltage is critical, especially when using a generator. Excessive voltage can damage equipment, and significant fluctuations may indicate issues with voltage regulation or fuel supply.

Monitoring current or amperage helps prevent overloads, especially when using a limited shore power supply or a motorhome park power source.

Frequency must be monitored when generators are part of the system. Frequency regulation can affect devices such as clocks, dimmer switches, and the efficiency of transformer-based equipment. Typically, frequency should not vary by more than ± 2 or 3 cycles across the generator's operating range.

The displayed power is the apparent power (Vrms x Irms) and can be used to avoid overloading sources such as an inverter.

To access scan mode, hold the button down for two seconds. Use the arrow buttons to scroll until 'SCAn' appears on the screen. Then press to select scan mode and use the arrows to choose 'On' or 'Off'.

To set an alarm, switch the meter to display mode for the relevant measurement (e.g., amperes for high-current alarm). Hold the button down for two seconds to access the MENU. Use the arrow buttons to scroll to the desired alarm option, then press to select it. You can then choose 'On' or 'Off' and adjust the threshold value.

The meter must be installed in a safe environment for high-voltage electrical connections. It should be placed in a visible position with easy access to the buttons, and personnel must not be able to touch the terminals on the rear of the meter. The location must be dry and protected.

The display face of the meter is splash-resistant and its printed circuits are coated for improved corrosion resistance. However, it is not designed for use in wet environments or for outdoor installation without additional protection.

Before installing the meter, it is essential to disconnect all AC power sources, including generators, inverters, and shore power or shore supply. For marine and RV installations, ensure you disconnect the shore power or shore supply and disconnect the DC power from the inverter. It is strongly recommended to consult a qualified electrician if you are not experienced in installing AC devices.

Yes, it is critical to disconnect all AC sources before installing the current transformer (CT). Never power up while the CT is not connected to the meter. Open CT leads during operation can generate lethal voltages. If the meter must be removed, the CT leads must be short-circuited.

Yes, it is necessary to use a twisted pair cable for the current transformer connections. This minimizes the susceptibility to electrical noise in the system, as the signal generated by the CT is very weak.

Yes, the 8200 series meters can be used to measure current flow in both phases of a 240 V three- or four-wire single-phase system. However, this requires the use of a switch specifically designed for this purpose.

A special switch is required, designed to bypass the secondary of the current transformer (CT) unless connected to the meter. Blue Sea Systems offers the switch and the PN 8410 panel for 120/240V applications. Similar switches are also manufactured by ElectroSwitch (series 31), Allen Bradley, and Kraus & Naimer.

Yes, unlike single-function meters such as models 8237 (voltmeter), 8238 (ammeter) or 8239 (frequency meter) from the same brand, the 8247-BSS consolidates voltage, current, frequency and power measurement into a single unit, providing a practical overview of your system's performance.

If the current transformer (CT) is left in an open circuit while primary current is flowing, high voltages are generated. If these voltages are connected to the meter, they may cause damage not covered by the warranty.

When powered on, the meter performs a self-test sequence that lights up all the function LEDs.