Bezdrátový plachtící balíček GNX™ 43

To install the gWind™ Wireless 2 sensor, follow these steps:

Install the supplied battery in the sensor by opening the compartment with a #2 Phillips screwdriver and connecting the battery to the dedicated port.
Choose a mounting location on a horizontal surface at the masthead, facing forward on the boat and parallel to the centerline.
Use the mounting bracket as a template to mark the pilot hole locations.
Drill pilot holes with a 4.5 mm (11/64 in) drill bit.
Secure the mounting bracket to the surface using the included screws.
Place the sensor into the mounting bracket by pushing and sliding it until it stops.
Hand-tighten the locking nut clockwise to secure the sensor.
Attach the safety clamp to the sensor to prevent the locking nut from loosening.
If the sensor is not precisely facing forward on the boat, you can adjust its orientation via the GNX™ Wind instrument to obtain accurate wind angle data.

For optimal performance of the GDT™ 43 transducer, mounting location is critical:

On fin-keel sailboats, mount it more than 25 cm and less than 75 cm ahead of the keel, and less than 10 cm from the centerline. On long-keel sailboats, mount it slightly angled toward the bow. Avoid mounting near sharp hull edges (chine corners) on powerboats. On single-screw boats, do not mount it in the propeller wash path. On twin-screw boats, mount it between the propellers if possible. The transducer must be parallel to the boat’s fore-aft axis. Ensure the transducer is accessible from inside the boat. Avoid locations behind frames, stiffeners, fittings, water intakes or outlets, or anywhere that could create air bubbles or turbulence. Do not mount it where it could be struck during launching, lifting, or storage. It must be in clean (non-turbulent) water for optimal performance.

Yes, the GNX™ 43 wireless sailing pack is fully compatible with an existing NMEA 2000® network. The GNX™ Wind instrument and the GDT™ 43 transducer (via its adapter) connect directly to the NMEA 2000 network. The NMEA 2000 network provides power to the instrument and transmits NMEA 2000 sensor data. The included NMEA 2000 cables and connectors allow you to connect devices to your existing network or to set up a basic NMEA 2000 network if needed.

The Garmin GNX™ 43 pack is designed to provide essential navigation data for sailing. It displays accurate wireless wind data (wind speed and direction) via the gWind™ Wireless 2 sensor. Additionally, through the GDT™ 43 transducer connected to the NMEA 2000 network, it provides depth, boat speed through water, and water temperature information.

The GNX™ Wind instrument is designed for flush mounting. Here are the general steps:

Cut out the flush-mount template (included in the box) and position it at the desired location.Drill a 10 mm (3/8 in) pilot hole if using a rotary tool, or use a 90 mm (3.5 in) hole saw to cut the mounting surface along the dotted line of the template.Adjust the hole size as needed with a file and sandpaper.Ensure the instrument fits properly and the mounting holes are aligned.Drill 2.8 mm (7/64 in) pilot holes for the screws. If mounting in fiberglass, use a countersink bit to drill only through the top gelcoat layer to prevent cracking.Remove the remaining template material.Place the supplied gasket on the back of the unit and apply marine sealant around the gasket to prevent leaks.Connect all necessary cables before placing the instrument in the cutout.Secure the instrument firmly to the mounting surface using the supplied screws. Apply anti-seize lubricant to stainless steel screws if mounting in fiberglass.Snap the bezel into place.

The GNX™ Wind instrument cannot directly receive NMEA 0183® data. However, it can display NMEA 0183 data from sources connected to a GNX 20 or GNX 21 device (sold separately) on the same NMEA 2000® network. It can also receive data from Nexus® instruments and sensors via a GND™ 10 device (sold separately).

The main components of the GNX™ 43 pack have specific water resistance ratings:

The GNX™ Wind instrument has an IEC 60529 IPX7 rating. This means it can withstand accidental immersion in water up to 1 meter for 30 minutes.The gWind™ Wireless 2 wind sensor has an IEC 60529 IPX6 rating. It is protected against heavy seas.

The Garmin GNX™ 43 pack is a complete offer that includes:

The GNX™ Wind instrumentThe gWind™ Wireless 2 sensorThe GDT™ 43 through-hull transducerA NMEA 2000 adapter for the GDT 43The NMEA 2000 cables and connectors required for installation.

The Garmin GNX™ 43 pack provides essential data for sailboat navigation:

Accurate wireless wind data, including wind speed and angle, via the gWind™ Wireless 2 sensor. Depth, boat speed, and water temperature data from the GDT™ 43 transducer, transmitted over NMEA 2000.

The gWind™ Wireless 2 sensor is powered by an internal battery. It is recommended to store the sensor in a location exposed to light to maintain battery charge. If the sensor is stored in a dark place for an extended period, it is advisable to replace the battery at the start of each sailing season to ensure optimal operation.

The GNX™ Wind instrument has water resistance compliant with IEC 60529 IPX7 standard, meaning it can withstand accidental immersion in water up to 1 meter for 30 minutes.The gWind™ Wireless 2 sensor has water resistance compliant with IEC 60529 IPX-6 standard, protecting it against heavy seas.

For optimal performance, the GDT™ 43 transducer must be installed in an area of clean (non-turbulent) water and parallel to the bow-stern axis of your vessel. Key considerations include:

On fin-keel sailboats: The transducer must be mounted more than 25 cm and less than 75 cm ahead of the keel, and within 10 cm of the centerline.

On long-keel sailboats: It must be mounted at a slight angle toward the bow, not parallel to the centerline.

General: Avoid mounting it behind planking, struts, fittings, water outlets, or any obstruction that could create air bubbles or turbulence. Ensure the location allows access to the transducer from inside the vessel.

For installing the GDT™ 43 transducer, you will need the following tools:

A drillA 43 mm (1 11/16 in) hole sawFor installations on fiberglass cored hulls: a 52 to 55 mm (2 1/16 to 2 3/16 in) hole sawMarine sealantSilicone greaseA cable cutterA metal file (for installations on metal hulls)Fiberglass cloth and resin (optional for sealing a cored fiberglass hull)A 43 mm cylinder, wax, tape, and casting epoxy (optional for sealing a cored fiberglass hull)

Installation on a fiberglass hull with a core requires specific preparation to seal the core and prevent water infiltration. The procedure is as follows:

Drill a 3 mm (1/8 in) pilot hole from the inside out through the hull. From the outside, use a 43 mm (1 11/16 in) hole saw to cut only the outer fiberglass skin. From the inside, at the pilot hole, use a hole saw to cut a hole 9 to 12 mm (3/8 to 1/2 in) larger than the outer hole through the inner skin and most of the core, without cutting the outer skin. Remove the cut inner skin and core. Sand and clean the area. Seal the core using either layers of fiberglass cloth and resin or a casting epoxy with a 43 mm cylinder as a spacer. Once the core is sealed and cured, you can proceed with transducer installation as described in the general instructions.

The GNX™ Wind instrument is designed for flush mounting in your dashboard. Here are the general steps:

Use the provided flush-mount template to mark the location and cutout.Cut the mounting surface using a 90 mm (3.5 in) hole saw or rotary tool.Drill pilot holes of 2.8 mm (7/64 in) for the mounting screws. If mounting the unit in fiberglass, use a countersink bit to drill a relief counterbore through the top gel-coat layer only to prevent cracking.Place the supplied gasket on the rear of the unit and apply marine sealant around the gasket to prevent leaks.Insert the instrument into the cutout and secure it firmly with the provided screws, applying anti-seize lubricant to the stainless steel screws if mounting in fiberglass.Snap the bezel into place.

The safe distance for the compass of the GNX™ Wind instrument is 209 mm (8.25 in). It is crucial to mount the device at least this far from a magnetic compass to prevent any interference that could affect compass accuracy.

The gWind™ Wireless 2 sensor must be mounted on a horizontal surface at the top of the mast. If no horizontal surface is available, an appropriate shim must be added to create one. The sensor must be installed facing the bow of the boat, parallel to the centerline. If the orientation is not exact, it can be adjusted via the GNX™ Wind instrument settings to receive accurate wind angle data.

Yes, the Garmin GNX™ 43 pack is designed to connect to an NMEA 2000 network. The GNX™ Wind instrument and the GDT™ 43 transducer (via its NMEA 2000 adapter) connect to the NMEA 2000 network, which provides power and data from other NMEA 2000 devices. The necessary NMEA 2000 cables and connectors are included to facilitate connection to an existing network or the creation of a basic network.

The GNX™ Wind instrument cannot directly receive NMEA 0183 data. However, it can display NMEA 0183 data from sources connected to a GNX 20 or GNX 21 device (sold separately) that are themselves connected to the same NMEA 2000 network.

Yes, the GNX™ Wind instrument can receive data from Nexus® instruments and sensors using a GND™ 10 device (sold separately). Additionally, the GDT™ 43 transducer can be connected to a Nexus® system by cutting its cable to the desired length and connecting the wires to the dedicated depth port on the Nexus® device.