ECLIPSE, reflektor flood 18 palců

The Garmin ECLIPSE Flood Light 18" is equipped with 12 x 10 W LEDs, delivering up to 10,000 lumens. It provides a 5000 K colour temperature and a wide beam angle of 70 to 90 degrees.

This spotlight operates within a voltage range of 10.5 to 31 VDC.

The projector's maximum consumption is 9.2A at 12V and 4.6A at 24V, for an average power of 110 W.

The spotlight can be controlled in several ways:

Via a simple on/off switch.Via a momentary switch.Using a compatible multifunction display (MFD).With a smart device.To control via MFD or smart device, adding an ECLIPSE Command Center or EOS-LUX Command Center is required.

Once integrated into an MFD or smart device via a Command Center, the projector can provide dynamic lighting effects such as strobe and dimming mode.

Yes, this spotlight has an IP68 protection rating, making it resistant to dust and immersion.

The projector housing is made of powder-coated aluminum and features a frosted lens.

The mounting location must be a flat and durable surface.

The mounting bracket uses a 6.5mm hole sized for an M6 bolt (included). A 7mm hole is also required for cable clearance.

The spotlight must be fastened to the brackets with a tightening torque of 5Nm. It is important not to overtighten.

Yes, this product must be installed, inspected and maintained only by a qualified electrician, in accordance with all applicable electrical codes.

The cable entry must be made watertight. Using a cable gland is recommended.

Yes, the spotlight can operate with a simple on/off switch (latching switch).

To activate dimming with a rocker switch:

Turn the switch on to power the light at full brightness.Switch the switch once to start the dimming cycle.Switch the switch again to pause the dimming cycle.Turn the switch off for 5 seconds to restart at full brightness.

No, the ECLIPSE Command Center installation is only suitable for 12V boats.

Use only water and soap with a soft cloth to clean the projector. Do not use any chemical cleaners and do not clean under pressure. Regular inspection of the projector must be performed.

LUMISHORE Ltd guarantees its lighting systems, including lights and associated accessories, against manufacturing defects for a period of three years from the original purchase date.

The warranty may be voided in cases of misuse, abuse, incorrect installation, negligence, improper shipping, damage caused by disasters (fire, flood, storm, lightning), installation by unqualified personnel, unauthorized repair or modification, or unapproved installations. Failure to comply with installation, maintenance, and usage instructions also voids the warranty.

To control multiple lights via an MFD, you will need an LUX Light Control Module and an EOS-LUX Command Center.

Installation of the Garmin ECLIPSE Flood Light 18-inch must be carried out by a qualified electrician in accordance with all applicable electrical codes. It is imperative to ensure the power supply is cut off before and during installation and maintenance.

Physical installation steps:Selecting the location: Choose a flat and durable mounting location.Drilling mounting holes: Use an appropriate drill bit to bore the support holes. The bracket has a 6.5 mm hole suitable for an M6 bolt (supplied).Cable routing: Drill a 7 mm (0.275 inch) hole for the cable. The cable must always be in a "fixed" position without movement or rotation. The cable entry must be sealed; using a cable gland is recommended.Attaching the brackets: Secure the brackets in place using the supplied M6 bolts and nylon insert nuts. Apply the appropriate torque based on the fasteners used and the mounting surface.Installing the floodlight: Mount the ECLIPSE floodlight onto the brackets using the supplied M6 bolt, washers, and nylon insert nut. Ensure the nylon washers are placed inside the stainless steel bracket. Tighten to 5 Nm torque, WITHOUT OVERTIGHTENING.Wiring and testing: Wiring must be done in accordance with ABYC directives. The floodlight operates within a voltage range of 10 to 31 VDC.

Simple control (toggle switch):Turn on the switch to power the floodlight at full brightness.Press the switch once to start the dimming cycle.Press the switch again to stop the dimming cycle.Turn off the switch for 5 seconds to restart at full brightness.Control via multifunction display (MFD): For MFD control, you will need an ECLIPSE Command Center or an EOS-LUX Command Center.With an ECLIPSE Command Center (12V boats only): Connect the ECLIPSE wiring harness (RED) to the FL18's RED, the YELLOW to the FL18's YELLOW, and the WHITE and BLUE to the FL18's BLACK.For multiple lights with an ECLIPSE Command Center, connect each FL18's RED to +10.5-15V (with individual fuse), each FL18's BLACK to ground, and the ECLIPSE harness YELLOW to each FL18's YELLOW.With an LUX Light Control Module and EOS-LUX Command Center: This system allows control of up to 16 lights. Operation is via a momentary switch: press to turn on, hold to adjust intensity, press to turn off.It is crucial to always cut the power supply before any intervention and to ensure all connections are watertight to guarantee product safety and performance.