LUX SL180, LED pás Cut-Seal, 1000 mm

The Garmin LUX SL180 LED light strip is a versatile and customizable lighting solution, specifically designed for the marine environment. It is part of Garmin/Lumishore’s LUX range and provides CRGBW lighting (cool white, red, green, blue, warm white).

The LUX SL180 light strip has a length of 1000 mm. It is designed to be precisely cut every 100 mm, allowing easy adaptation to various spaces aboard your boat.

The LUX SL180 LED strip has an IP68 waterproof rating. This means it is fully encapsulated and water-resistant, making it suitable for damp areas. However, it is not designed for continuous submersion in water.

The average power consumption of the LUX SL180 strip is 8.7 W per meter, with a nominal power of 5 watts per meter.

The compact dimensions of the LUX SL180 strip are 5 mm in depth and 14.5 mm in height. These dimensions allow for discreet installation under the toe rail or behind panels.

Yes, the LUX SL180 LED light strip is made from UV-resistant material. However, it is recommended not to install it in areas exposed to strong and prolonged direct sunlight.

During installation, handle the strip carefully:

Do not drop or twist it. Do not bend it horizontally or twist it. Do not apply pressure to the LED area; press only the edge of the strip. For lengths over one meter, use two people. Carefully unwind it from the reel and lay it flat in a straight line.

The LUX SL180 light strip has a minimum bending radius of 50 mm on the vertical axis. It is imperative not to bend it on the horizontal axis or twist it, as this could damage it and void the warranty.

To cut and seal the tape:

Unroll the tape on a flat surface and identify the cutting point closest to the desired length (every 100 mm).Cut only at the marked cutting points using scissors, in one single motion at the center of the cutting tabs.Remove 20 mm of the adhesive backing at the end to be sealed, then lightly scratch the adhesive 10 mm from the end to expose the silicone.Half-fill the end cap with the provided silicone adhesive.Attach the end cap, clean off excess adhesive, and allow to cure for 24 hours before handling.

The strip can be mounted in several ways:

3M adhesive: Clean the mounting surface thoroughly with IPA, remove the 3M adhesive backing, and press the strip firmly into place. Allow the adhesive to cure for 24 hours before powering on the light.Mechanical fasteners: For outdoor installations, wet areas, or tight bends, it is recommended to use mechanical fasteners (mounting clips) in addition to the adhesive. These clips should be spaced 25 to 30 cm apart and/or placed on either side of a bend.Optional mounting clips: For narrow mounting channels, stainless steel metal clips may be provided. They are secured with a countersunk screw.

Yes, it is imperative to always ensure that the boat's power source and battery are disconnected or isolated before installing the light strip.

It is strongly recommended that a qualified professional perform the electrical and mechanical installation of the LUX SL180 light strip to ensure correct installation and maintain the validity of the warranty.

After sealing the end of the tape with the supplied silicone adhesive, it is necessary to allow the adhesive to cure for a full 24 hours before handling the tape or applying power to it.

The LUX SL180 light strip is designed to be used exclusively with Lumishore Lux Strip Light Driver control modules. Using any other third-party lighting control product or driver will void the warranty.

The LUX SL180 light strip operates with an input voltage range of 23-25 V via the Lumishore Lux Strip Light driver module, or 10.5-31 VDC via a LUX control module. It is critical to use only the specified Lumishore driver modules.

No, the LUX SL180 LED strip must be connected only to Lumishore Lux Strip Light Driver control modules. Using third-party lighting control or driver products will void the product warranty.

Lumishore lighting systems and accessories (including the LUX SL180 strip) are warranted against manufacturing defects for a period of three years from the original purchase date.

The warranty will be void in the following cases:

Improper use, abuse, or incorrect installation.
Negligence, improper shipping, or damage caused by disasters (fire, flood, storm, lightning).
Installation by unqualified personnel, unauthorized repair, or modification.
Unapproved installations or failure to comply with installation, maintenance, and usage instructions specified in the manual.
Use with third-party drivers other than Lumishore Lux Strip Light Driver modules.

No, cutting and sealing the LED strip does not void the warranty, provided that all instructions detailed in the installation manual are strictly followed. It is mandatory to use only the provided sealant for sealing.