LUX SL180, páskové osvětlení, CRGBW, 1800 mm

The Garmin LUX SL180 LED strip offers a full spectrum of colors (CRGBW), including cyan, red, green, blue, as well as tunable white. The white can be adjusted from a cool white to a warm white, with a color temperature range from 2700K to 6500K.

The Garmin LUX SL180 LED strip has a predefined length of 1800 mm (1.8 meters). It is delivered in factory-sealed lengths and must not be cut.

The LUX SL180 LED strip consumes 5 watts per meter.

Yes, the LUX SL180 LED strip is fully sealed and IP68 certified. It can be installed indoors or outdoors, including in damp areas. However, it is not designed for permanent immersion in water.

The LUX SL180 LED light bar is made from UV-resistant materials and has been tested for salt spray resistance, making it suitable for marine environments.

No, the LUX SL180 LED strip is supplied in predefined, factory-sealed lengths to maintain its IP68 rating. It must not under any circumstances be cut.

The LUX SL180 LED strip light offers tunable white with a color temperature range from 2700K (warm white) to 6500K (cool white).

The flexibility of the strip is limited to a minimum bending radius of 50 mm on the vertical axis only. It must not be bent on the horizontal axis or twisted.

The LUX SL180 banner can be installed indoors or outdoors, including in damp areas, thanks to its fully sealed design and IP68 certification. However, it must not be installed in areas exposed to strong direct sunlight or permanently submerged in water.

The strip can be mounted in several ways:

3M adhesive: Remove the adhesive backing and press firmly along the edges of the strip (avoid applying pressure on the LEDs). Allow the adhesive to cure for 24 hours.Mechanical fasteners: For outdoor installations, wet areas, or tight radii, use mechanical fasteners (mounting clips) in addition to the adhesive. These clips should be spaced every 25 to 30 cm and/or on each side of a curve.Stainless steel mounting clips (optional): May be supplied for narrow mounting channels.

Yes, for outdoor installation or in wet areas, it is highly recommended to use mechanical fastenings (mounting clips) in addition to the adhesive layer to ensure optimal and durable mounting of the light strip.

Yes, it is essential to thoroughly clean the mounting surface with isopropyl alcohol (IPA) to ensure it is free of dust and dirt before applying the adhesive.

It is recommended to let the adhesive set for 24 hours before turning on the LED strip to ensure maximum adhesion.

Yes, during installation, do not apply pressure to the LED area. Press only the edges of the strip to secure it properly.

For banner lengths exceeding 1 meter, it is recommended that two people perform the installation: one person to secure the banner and another to hold and unroll it carefully.

The LUX SL180 LED strip is specifically designed to be used only with Lumishore LUX LED strip driver modules. It is imperative to use this type of driver to ensure proper operation and the validity of the warranty.

No, the LUX SL180 LED strip must only be connected to Lumishore LUX LED strip driver modules. Using third-party lighting control products or drivers will void the product warranty.

The LUX SL180 LED strip operates within an input voltage range of 23 to 25V. It is essential to use only Lumishore LUX LED strip driver modules to meet this voltage requirement.

Garmin (via Lumishore) guarantees its lighting systems, including the LUX SL180 strip, against manufacturing defects for a period of three years from the original purchase date.

The warranty may be voided in case of misuse, abuse, incorrect installation, negligence, inadequate shipping, damage caused by disasters (fire, flood, lightning), installation by unqualified personnel, unauthorized repair or modification, or unauthorized installations. Failure to comply with installation, maintenance, and usage instructions in the installation document also constitutes a breach of warranty conditions, including use with third-party drivers.