LUX SL180, páskové osvětlení, CRGBW, 5000 mm

The Garmin LUX SL180 LED light bar uses CRGBW LEDs (cool white, red, green, blue, warm white), allowing it to provide a full color spectrum. It also offers adjustable white light with a temperature range from 2700 K to 6500 K.

The Garmin LUX SL180 light strip has a length of 5000 mm, i.e. 5 meters.

The Garmin LUX SL180 light strip consumes 5 watts per meter. For a length of 5000 mm, the total consumption is 25 watts.

The Garmin LUX SL180 LED strip allows adjusting the white temperature, with a range from 2700 K (warm white) to 6500 K (cold white).

The LUX SL180 LED light bar has an IP68 protection rating. This means it is fully sealed, encapsulated, and resistant to water splashes and dust. However, it is not designed for permanent submersion in water.

Yes, the LUX SL180 LED light strip is made from UV-resistant materials and has undergone salt spray testing, ensuring durability in marine environments.

No, the LUX SL180 LED strip is rated IP68, making it resistant to water splashes and dust, but it is not designed for permanent submersion. It is intended for indoor and outdoor applications above the waterline.

To operate, the LUX SL180 LED strip requires the Lumishore LUX Strip Light Driver control module. This module is sold separately and is essential for compatibility and proper operation of the lighting.

No, it is mandatory to use the LUX SL180 light strip exclusively with Lumishore LUX Strip Light Driver modules. Using third-party lighting control products or drivers is not supported and will void the warranty.

The LUX SL180 LED strip requires an input voltage of 23 to 25V for operation. It must be connected to the Lumishore LUX Strip Light Driver module.

No, the LUX SL180 LED light strip is supplied in predefined, factory-sealed lengths to meet IP68 standards. Cutting the light strip is strictly prohibited as it would compromise its waterproofing and void the warranty.

Installation is done using a 3M adhesive strip. For reinforced mounting, especially outdoors, in wet areas or with tight bend radii, mechanical fasteners (mounting clips) are recommended as a supplement. These clips can be provided by Lumishore as an optional accessory.

Always ensure the vessel's power source and the battery are disconnected or isolated before installation. Do not bend the LED strip along the horizontal axis or twist it. The minimum bending radius is 50 mm and only along the vertical axis. Do not apply pressure on the LEDs, only on the edges of the strip during installation. For lengths exceeding 1 meter, it is recommended to install the strip with two people. Unroll the strip carefully and lay it flat without allowing it to bend, twist, or tangle.

The LUX SL180 light strip has a minimum bending radius of 50 mm, but only on the vertical axis. It is important not to bend it on the horizontal axis or twist it to avoid damaging the product.

Yes, the LUX SL180 LED strip is designed to be installed indoors or outdoors above the waterline, including in damp areas. However, it must not be installed in areas exposed to prolonged direct sunlight, even though it is made with UV-resistant materials.

Before applying the 3M adhesive tape, the mounting surface must be thoroughly cleaned with isopropyl alcohol (IPA) to ensure it is free of dust and dirt. A clean surface guarantees optimal adhesion.

For outdoor installations in wet areas or when tight bend radii are required, it is strongly recommended to use mechanical fasteners (mounting clips) in addition to the 3M adhesive tape. Clips should be spaced 25 to 30 cm apart and/or placed on each side of a bend.

After firmly pressing the light strip into place with the 3M adhesive, it is necessary to allow the adhesive to set for 24 hours before turning on the light strip. This ensures maximum adhesion.

The warranty for the LUX SL180 LED strip, valid for three years from the date of purchase, may be voided in the following cases:

Improper use or abuse of the product.Incorrect installation or lack of maintenance.Damage caused by disasters (fire, flood, lightning).Installation performed by unqualified personnel.Any unauthorized repair or modification.Failure to comply with the installation, maintenance, and usage instructions provided in the manual.Using the LED strip with third-party pilot modules or lighting control products other than the Lumishore LUX Strip Light Driver.

To ensure the validity of the warranty and the safety of the installation, it is imperative that a qualified professional carries out both the electrical and mechanical installation of the LUX SL180 LED strip.