Sada Reactor™ 40 pro Volvo-Penta® s přístrojem GHC™ 50

The GHC 50 instrument is designed for flush mounting in your dashboard. Here are the considerations and tools required:

Required tools: Drill with bits (9 mm, 2.5 mm, 3.5 mm, 4 mm), Phillips screwdriver size #2, jigsaw or rotary tool, file and sandpaper, marine sealant (recommended). Mounting considerations: The mounting location must be at or below eye level, the surface must be flat and sufficiently rigid to support the device’s weight and protect it from excessive vibration. The space behind the surface must allow for cable routing and connections. Precautions: Do not mount the device in an area exposed to extreme temperatures (outside the range of -15°C to 55°C). To avoid interference with a magnetic compass, maintain a safety distance of 20 cm. General procedure: Use the provided template to mark and cut the opening. Drill mounting holes according to the chosen method (wood screws or nut plates). Install the sealing gasket at the rear of the device, connect the necessary cables if access is limited after installation, then secure the device in the opening with the supplied screws.

Yes, to avoid potential personal injury and damage to your sailboat, the autopilot system must be installed by a qualified marine installer. Specific knowledge of marine steering and electrical systems is required for correct installation.

This Reactor™ 40 kit is specifically designed for Volvo-Penta® electronic steering systems (Steer-by-Wire).

After physical installation, the autopilot system must be configured and adjusted according to your boat’s dynamics. This is done using two main assistants:

The Dockside Wizard: It can be completed when the boat is afloat or out of the water (if afloat, the boat must be stationary). It guides you through initial setup steps such as selecting the vessel type, testing the rudder direction, selecting the speed source, and checking the tachometer. The Sea Trial Wizard: This must be performed in calm, open water. This assistant configures the autopilot’s core sensors and includes steps like setting the planning mode or maximum speed, calibrating the compass, and running the Autotune procedure. Configuration can be done using the GHC 50 instrument or a compatible chartplotter connected to the same NMEA 2000 network.

No, the GHC 50 instrument is powered by the NMEA 2000 network and does not require a separate power connection. The NMEA 2000 network supplies power to the instrument and enables communication with other autopilot components.

The GHC 50 instrument has an IEC 60529 IPX7 waterproof rating, meaning it can withstand accidental immersion in water up to 1 meter for 30 minutes. Its operating temperature range is -15°C to 55°C (5°F to 131°F).

No, the GHC 50 cannot be updated using only an NMEA 2000 network connection. While the NMEA 2000 connection is essential for autopilot operation, a connection to Garmin marine network devices via a Garmin marine network cable (sold separately) is recommended for software updates, especially if a Garmin chartplotter is present on the network.

To avoid interference with a magnetic compass, the GHC 50 instrument must not be installed within 20 cm (7.87 inches) of it.

Yes, the documentation strongly recommends that the installation of the autopilot system be carried out by a qualified marine installer. This is due to the specific knowledge required in marine steering and electrical systems, which are essential for correct installation and to avoid potential damage to the boat or personal injury.

For installing the GHC 50 instrument, you will need the following tools:

A drill with 9 mm (3/8 in), 2.5 mm (3/32 in), 3.5 mm (9/64 in), and 4 mm (5/32 in) drill bits. A #2 Phillips screwdriver. A jigsaw or rotary tool. A file and sandpaper. Marine sealant (recommended).

When selecting the mounting location for the GHC 50, consider the following points:

The location should be at eye level or below for optimal viewing.The mounting surface must be flat, sturdy enough to support the device’s weight, and protect it from excessive vibration or shock.To avoid interference with a magnetic compass, the device must not be installed closer than the 20 cm (7.87 in) safety distance from a compass.There must be sufficient space behind the mounting surface for cable routing and connections.The device must not be exposed to temperatures outside the -15°C to 55°C range.

The GHC 50 instrument connects to the boat's NMEA 2000 network. It is powered by this network; no separate power connection is required.

It is important that the GHC 50 is connected to the same NMEA 2000 network as the other autopilot components to ensure correct operation. If you install a new NMEA 2000 network, the NMEA 2000 power cable must be connected to the boat's ignition switch, not directly to the battery.

The autopilot system must be configured and adjusted to your boat's dynamics. This process is primarily carried out via two assistants: the Dockside Wizard and the Sea Trial Wizard.

The Dockside Wizard guides you through the initial setup steps, such as selecting the vessel type, testing the rudder direction, and choosing the speed source. It can be performed when the boat is in the water (stationary) or out of the water.

The sea trial assistant (Sea Trial Wizard) is essential for configuring the fundamental sensors of the autopilot and must be performed under suitable conditions. It is recommended to carry it out in an open, calm water area where the boat does not pitch at rest or at very low speed, and is not significantly affected by wind.

During the procedure, the weight aboard the boat must remain balanced, and it is advisable not to move around to ensure the accuracy of the configuration.

This Garmin Reactor 40 kit is specifically designed for Volvo-Penta® electronic steering systems (Steer-by-Wire). It is not compatible with other types of steering systems.

No, the GHC 50 instrument cannot be updated solely via an NMEA 2000 network connection. For software updates, it is recommended to connect it to Garmin Marine Network devices using a Garmin Marine Network 9-pin cable (sold separately), especially if a Garmin chartplotter is present on the network.

The dimensions of the GHC 50 instrument without the sunshade are 105 mm (height) x 140 mm (width) x 51 mm (depth). With the sunshade, the dimensions are 113 mm (height) x 144 mm (width) x 56 mm (depth).

The GHC 50 instrument has an IEC 60529 IPX7 waterproof rating. This means it can withstand accidental immersion in water up to 1 meter deep for a maximum of 30 minutes.

The recommended safe distance from a compass for the GHC 50 instrument is 20 centimeters (7.87 inches). It is important to respect this distance to avoid any interference with the operation of a magnetic compass.

The Garmin GHC 50 instrument is designed for flush mounting in your dashboard. Here are the key steps and considerations for its installation:

Required tools: You will need a drill with drill bits (9 mm, 2.5 mm, 3.5 mm, 4 mm), a Phillips screwdriver size #2, a jigsaw or rotary tool, a file, sandpaper, and marine sealant (recommended). Mounting considerations: Choose a location where the surface is flat, sufficiently robust to support the weight of the device, and with adequate space behind for cable routing. To avoid interference with a magnetic compass, the device must not be installed within 20 cm of it. Mounting procedure: Use the template and hardware included to cut the opening in the dashboard and secure the device. Two mounting options are available: wood screws or nut plates and machine screws, depending on the material of your mounting surface. Electrical connection: The GHC 50 is powered via the NMEA 2000 network and does not require a separate power connection. It is essential that the GHC 50 be connected to the same NMEA 2000 network as other autopilot components (such as the CCU) to ensure proper system operation. Software updates: For software updates, it is recommended to connect the device to Garmin Marine Network devices using a Garmin Marine Network cable (sold separately) if a Garmin chartplotter is present on the network. The device cannot be updated solely via an NMEA 2000 connection.