Sonda ActiveImaging™ 3v1 s 7,6 m kabelem (25 stop)

This is an underwater imaging transducer designed for fishing. It integrates traditional CHIRP, SideScan and DownScan Imaging, along with a temperature sensor, all in a single unit for simplified installation.

The Navico ActiveImaging™ 3-IN-1 transducer combines traditional CHIRP, SideScan and DownScan Imaging technologies. It also includes a temperature sensor for measuring depth and water temperature.

Active Imaging™ technology optimizes SideScan beam steering to enhance imaging resolution and range. It enables identification of underwater structures such as rock formations, seagrass beds, and drop-offs at greater distances, providing finer details over a larger area.

This transducer operates on CHIRP mid/high frequencies (83/200 kHz) for traditional CHIRP, and specific frequencies for SideScan and DownScan Imaging to optimize imaging.

Yes, the Navico ActiveImaging™ 3-IN-1 transducer is equipped with a sensor that provides depth and water temperature data.

The weight of the ActiveImaging™ 3-IN-1 transducer without its cable is 0.37 kg (0.81 lbs).

The transducer is made of polymer. This material was selected because it reacts to sound waves in a manner similar to water, thereby contributing to the clarity of underwater images.

The transducer uses separate sonar elements for SideScan transmission and reception. This design increases ping speed and image resolution, while improving lateral range compared to older imaging sounders.

This transducer is compatible with Lowrance HDS LIVE, HDS Carbon, Elite Ti2 multifunction displays, as well as Simrad NSS evo3 and GO series.

The Navico ActiveImaging™ 3-IN-1 transducer is equipped with a 9-pin connector, ensuring a reliable connection with compatible devices.

The transducer comes with a 7.6 m (25 ft) cable.

The ideal mounting location for the transducer is in an area with undisturbed water flow to optimize sonar signal quality.

Yes, it is not recommended to mount the transducer above the chine line of the boat, as this could disrupt water flow and affect the depth sounder's performance.

For installation, the recommended pilot hole diameters for screws of diameter 10 are:

For soft materials (e.g., plywood): Ø 3.7–4.0 mm (5/32"). For rigid materials (e.g., fiberglass, acrylic, hardwood): Ø 4.1–4.7 mm (3/16").

It is recommended to apply a high-quality marine-grade sealant/adhesive, suitable for use above or below the waterline, to the mounting holes to ensure a watertight seal.

Yes, through-hull mounting (shoot-thru-hull) is an installation option for this transducer, providing protection against damage and a discreet setup.

No, through-hull transducers cannot be installed through wooden hulls. This method is generally reserved for fiberglass or composite hulls.

"3-IN-1" indicates that the transducer combines three key imaging technologies in a single unit: traditional CHIRP, SideScan, and DownScan Imaging. This provides a comprehensive and detailed view of the underwater environment.

The Navico ActiveImaging™ 3-IN-1 transducer is designed to be compatible with multiple ranges of multifunction displays, ensuring seamless integration with your navigation system. It is compatible with:

Lowrance HDS LIVE multifunction displays
Lowrance HDS Carbon multifunction displays
Lowrance Elite Ti2 multifunction displays
Simrad NSS evo3 series
Simrad GO series

To ensure optimal performance of your ActiveImaging™ 3-IN-1 depth sounder, it is essential to follow the following mounting recommendations:

Ideal location: The transducer must be installed in an area where water flow is undisturbed.
Avoid locations: It is strongly discouraged to mount the transducer beyond the chine of your boat.
Mounting options: The transducer can be installed in different ways, including on the transom, on an electric bow thruster, or via a through-hull installation.
Recommended pilot holes for screws with a diameter of 10 mm:
For soft materials (e.g., plywood): use a drill bit of Ø 3.7–4.0 mm (5/32").
For rigid materials (e.g., fiberglass, acrylic, hardwood): use a drill bit of Ø 4.1–4.7 mm (3/16").
Sealing: Apply a high-quality marine-grade sealant/adhesive, suitable for use above or below the waterline, to all pilot holes to ensure watertightness.
Important note for through-hull installation: Scanning transducers cannot be used with wooden hulls.