Blue Smart IP67 nabíječka 12/7 DC

The Victron Blue Smart IP67 charger is designed to be extremely rugged and resistant. Its housing is made of die-cast aluminum and its electronics are fully encapsulated in resin. This design provides complete protection against water, oil, dust (IP67 rating), shocks, and is also flame-retardant.

The Blue Smart IP67 12/7 charger stands out with a high energy efficiency of 93%. Thanks to this high efficiency, it minimizes heat loss. Additionally, once the battery is fully charged, its power consumption drops to less than 1 Watt, which is highly efficient.

The charger is protected against overheating and can be used in hot environments, such as an engine room. The output current will automatically decrease as the temperature rises above 40 °C (with a 3 % reduction per °C above 40 °C), but the charger will not fail and will continue to operate.

Yes, the Victron Blue Smart IP67 12/7 charger is completely silent. It has no cooling fan or other moving parts, ensuring noise-free operation.

The dimensions of the Blue Smart IP67 12/7 charger are 85 mm (height) x 211 mm (width) x 60 mm (depth). Its weight is 1.8 kg.

The charger is equipped with multiple safety protections to ensure safe operation:

Protection against battery polarity reversal (via an external ATO fuse). Protection against output short circuits. Protection against overheating.

The charger has two LEDs to indicate its operating status and charging cycle:

A yellow LED indicating the charging cycle: fast blinking for bulk charge, slow blinking for absorption, steady for float mode, and off for storage mode. A green LED indicating that the device is powered on.

Yes, the Blue Smart IP67 12/7 charger can also be used as a power supply, providing additional versatility.

Yes, the Blue Smart IP67 charger includes temperature compensation. It measures ambient temperature during the test phase and adjusts the optimal charging voltage for lead-acid batteries based on this temperature. This eliminates the need for manual adjustments in cold or hot environments, ensuring optimal charging.

The Blue Smart IP67 12/7 charger is designed to efficiently charge lead-acid batteries (including gel, AGM, and flooded types) and Li-ion batteries.

The charger is suitable for lead-acid and Li-ion batteries with a capacity between 14 Ah and 225 Ah.

Yes, the Blue Smart IP67 12/7 charger has a recovery function for fully discharged batteries. It will attempt to recharge a battery even if it has been discharged to 0 volts, using a low current initially, then resuming normal charging once sufficient voltage is detected.

Yes, the charger can charge Li-ion batteries. It uses a simplified charging algorithm specifically adapted for Li-ion batteries (bulk – absorption – float).

The integrated Bluetooth Smart feature allows you to connect the charger to your smartphone, tablet or other device via the VictronConnect app. You can monitor voltage and current, adjust charging parameters and wirelessly update the charger’s firmware.

The VictronConnect application is available for Windows PC and macOS users, as well as for iOS and Android smartphones and tablets, enabling flexible management of the charger.

The charger must be installed in a well-ventilated area near the battery. It is important not to place it directly above the battery due to potential corrosive gases that may be emitted by the battery and damage the charger.

To connect the charger to the battery, follow these steps:

Connect the negative cable (black) to the negative terminal (–) of the battery. Connect the positive cable (red) to the positive terminal (+) of the battery. Ensure the ring terminals are properly secured. These connections must be made only after unplugging the AC power cord from the electrical outlet.

The charger operates with an input voltage range of 180 to 265 VAC and a frequency of 45 to 65 Hz. The nominal supply voltage is 220-240 VAC 50-60 Hz.

Yes, the Blue Smart IP67 charger is designed to operate in very humid environments, with humidity up to 100%. Its IP67 rating ensures complete protection against water and dust ingress.

Once the DC cables are correctly connected to the battery (black cable to the negative terminal, red cable to the positive terminal), plug the AC power cord into the wall outlet. The charging cycle will start automatically.