MultiPlus C 12/2000/80-30

The Victron Energy MultiPlus C 12/2000/80-30 is a multifunctional power solution. It integrates a pure sine wave inverter, a sophisticated battery charger with adaptive charging technology, and a high-speed AC transfer switch, all in a single enclosure.

The MultiPlus C 12/2000/80-30 inverter provides continuous power of 2000 VA, equivalent to 1600 W. Its peak power can reach 4000 W.

The MultiPlus C 12/2000/80-30 delivers an output voltage of 230 VAC ± 2% and a frequency of 50 Hz ± 0.1%, ensuring stable power supply for connected equipment.

Yes, the MultiPlus C has a UPS (Uninterruptible Power Supply) function. In the event of a mains power failure, the inverter activates automatically and takes over in less than 20 milliseconds, ensuring continuous operation of electronic equipment.

The battery charger is an adaptive four-stage microprocessor-controlled management system. It includes the following phases:

Bulk (bulk charge)AbsorptionFloat (float maintenance)Storage (storage)This adaptive function automatically adjusts the charging process based on battery usage to optimize its lifespan.

The main charger of the MultiPlus C 12/2000/80-30 can supply a maximum charging current of 80 A for the service battery.

Yes, the MultiPlus C is equipped with a second DC output specifically intended for charging a starter battery. This output is limited to a current of 4 A and has a slightly lower output voltage.

The PowerControl function limits the AC input current from a generator or shore power supply. The MultiPlus C takes other AC loads into account and uses any excess current for battery charging, thus preventing overload of the generator or shore power supply.

The PowerAssist function allows the MultiPlus C to supplement the capacity of the alternative source (generator or shore power). During power peaks, when demand exceeds the AC source capacity, the unit draws the necessary energy from the battery to provide additional power to the load. When the load decreases, the excess power is used to recharge the battery.

Yes, the MultiPlus C is equipped with a programmable relay. By default, it is configured as an alarm relay, but it can be programmed for various other applications, such as a start relay for a generator.

The MultiPlus C comes with a temperature sensor. This sensor automatically reduces the charging voltage when the battery temperature rises. This function is essential, particularly for maintenance-free batteries, to prevent overcharging and drying out.

The BatterySafe mode is a function that prevents damage caused by excessive gas release during charging. If a high charging current is combined with a high absorption voltage to charge a battery quickly, the MultiPlus C automatically limits the rate of voltage increase once the gassing voltage is reached, thus protecting the battery.

Storage mode activates when the battery has not been discharged for 24 hours. In this mode, the float voltage is reduced to 2.2 V/cell (13.2 V for a 12 V battery) to minimize gassing and corrosion of the positive plates. Once a week, the voltage is raised to the absorption level to "equalize" the battery, preventing electrolyte stratification and sulfation.

The product must be installed in a dry, well-ventilated location, as close as possible to the batteries. It is essential to leave at least 10 cm of free space around the device to ensure adequate cooling.

This product must be installed by a qualified electrician. Here are important precautions:

Ensure continuous protective grounding at the AC input and/or output terminals.Make sure DC and AC input cables are protected by fuses or circuit breakers.Never mount the product directly above batteries.Install the product in a heat-resistant environment, away from chemicals, textiles, or other flammable materials.

No, it is explicitly stated that you must never install the product directly above the batteries. This is an important safety measure to prevent any risk related to battery gases.

Yes, it is crucial to leave a free space of at least 10 cm around the MultiPlus C for adequate ventilation. Excessively high ambient temperature can reduce the device's lifespan, the charging current, and the inverter's peak capacity, or even cause it to shut down.

Yes, the MultiPlus C 12/2000/80-30 can operate in parallel. Up to 6 inverters can be connected in parallel to achieve higher output power and meet increased energy demands.

Yes, the MultiPlus C 12/2000/80-30 can operate in a three-phase configuration, allowing flexibility for integration into more complex electrical systems.

The adaptive battery management system of the MultiPlus C, microprocessor-controlled, can be adjusted to suit various battery types. The adaptive function automatically adjusts the charging process based on battery usage, thereby optimizing its lifespan.