SmartSolar MPPT VE.Can 250/70 Tr RS

The ultra-fast MPPT technology enables the SmartSolar VE.Can charge controller to optimize energy harvesting from solar panels, especially when light intensity changes continuously, such as in cloudy conditions. This can increase energy production by up to 30% compared to PWM controllers and up to 10% compared to slower MPPT controllers.

The SmartSolar VE.Can controller is equipped with an innovative algorithm for advanced maximum power point (MPP) tracking. In cases of partial shading, where multiple MPPs may exist, this algorithm ensures constant locking onto the optimal MPP, thereby maximizing energy yield.

The SmartSolar VE.Can charge controller supports battery voltages of 12 V, 24 V, and 48 V with automatic detection. For 36 V, manual selection is required.

The SmartSolar VE.Can controller can accept a maximum absolute open-circuit voltage from the solar panels of 150 V under the coldest conditions. The maximum start-up and operating voltage is 145 V.

The SmartSolar VE.Can charge controller offers exceptional conversion efficiency, exceeding 98 %. It operates without a cooling fan, contributing to its durability and low standby consumption (less than 35 mA at 12 V and 20 mA at 48 V).

Yes, the SmartSolar VE.Can controller includes extended electronic protection, including:

Overheat protection and power reduction in case of high temperature.
Short-circuit protection (PV).
PV polarity reversal protection.
PV reverse current protection.

The SmartSolar VE.Can controller integrates Bluetooth Smart, enabling wireless configuration, monitoring, and updates via the VictronConnect app on smartphone or tablet. It can also be connected to a GX device (such as a Color Control GX) via VE.Direct or VE.Can for remote monitoring and management through the Victron Remote Management (VRM) portal.

Up to 25 SmartSolar VE.Can controllers can be synchronized via the VE.Can interface for coordinated battery bank management. Additionally, up to 10 units can be synchronized via Bluetooth Smart.

Yes, an optional SmartSolar plug-in LCD display is available. Simply remove the rubber gasket protecting the front port of the controller and plug in the display to view operating data.

Yes, the SmartSolar VE.Can controller has a fully discharged battery recovery function. It can initiate charging even if the battery has been discharged to zero volts and will reconnect to a fully discharged Li-ion battery with built-in disconnect function.

The SmartSolar VE.Can controller can communicate with external sensors via Bluetooth to obtain precise information on battery voltage and temperature, as well as current in some cases. Compatible devices include the Smart Battery Sense, the BMV-712 Smart battery monitor, or a SmartShunt.

Yes, the SmartSolar VE.Can controller is equipped with a programmable DPST-type relay. It can be configured to trigger on an alarm or other specific events. Its specifications are: 240 VAC / 4 A for AC and 4 A up to 35 VDC, 1 A up to 60 VDC for DC.

The SmartSolar VE.Can controller is designed for indoor installation in an unconditioned environment. It has an IP43 protection rating for electronic components and IP22 for the connection area.

The SmartSolar VE.Can controller is available in models with two pairs of MC4 connectors or Tr terminals (35 mm² / AWG2) for PV panel connection. For MC4 models, multiple parallel connection splitters may be required to connect solar panel strings in parallel.

The SmartSolar VE.Can controller can operate within a temperature range of -30 to +60 °C. It maintains its full nominal power up to 40 °C.

The SmartSolar VE.Can battery controller terminals are designed for 35 mm² / AWG2 cables.

Yes, the SmartSolar VE.Can controller has a remote on/off function via a 2-pin connector. This allows it to be connected, for example, to a VE.BUS BMS for external control.

The SmartSolar VE.Can controller offers a fully programmable charging algorithm as well as eight pre-programmed algorithms, selectable via a rotary switch. The charging algorithm is an adaptive multi-stage type.

Yes, the SmartSolar VE.Can controller firmware can be updated. This is typically done via the VictronConnect app, using the integrated Bluetooth connectivity.