Mastervolt AC Master 24/2500 pure sine wave inverter - 230 V 50/60 Hz AU/NZ wired

The Mastervolt AC Master 24/2500 inverter delivers a continuous power output of 2500 W at 40 °C with a power factor of 1. It can handle peak loads up to 3000 W for 3 seconds and up to 4000 W for 0.2 seconds, making it suitable for equipment requiring high inrush current.

The Master 24/2500 AC inverter produces a pure sine wave. This high-quality waveform is essential for safely powering sensitive electronic equipment without risk of damage or malfunction.

The Mastervolt AC Master 24/2500 inverter is designed to operate with a nominal battery voltage of 24 V DC.

The dimensions of the Mastervolt AC Master 24/2500 inverter are 283 x 436 x 128 mm (H x W x D).

Yes, the Mastervolt AC Master 24/2500 inverter has an automatic energy-saving mode. This mode optimizes battery consumption by reducing power draw when there is no load. The energy-saving threshold can be adjusted via DIP switches 4, 5, and 6, provided the energy-saving mode is selected (DIP switch 7 = 0).

Yes, the AC Master 24/2500 allows multi-unit configurations. You can create a parallel system with 2 to 15 units to increase total output power. For this, all units must be identical, have the same part numbers, and be configured with the same AC output voltage and frequency via DIP switches 1 and 3. A master/slave mode is available via DIP switch 7.

The Mastervolt AC Master 24/2500 inverter can operate within an ambient temperature range of -20 °C to 60 °C. Power derating may be required above 35 °C.

The Mastervolt AC Master 24/2500 inverter is equipped with a 20 Amp AC input circuit breaker.

For the AC Master 24/2500 inverter, the minimum recommended DC cable cross-section is 50 mm².

The Mastervolt AC Master 24/2500 inverter provides fast switching times:

From inverter to AC input: 8 to 10 ms. From AC input to inverter: 16 to 50 ms.

The inverter is equipped with multiple protections to ensure the safety and durability of the system:

OvervoltageOverloadShort-circuitLow/high battery voltageOvercurrent AC (via integrated circuit breaker)

Yes, the AC Master 24/2500 inverter can be used in a three-phase configuration. Up to 3 units (one per phase) can be used to create a three-phase system. Ensure that the master/slave mode is selected (DIP switch 7 = 1) for this configuration.

Yes, the AC Master 24/2500 inverter has a port offering two functions, including that of a remote switch. In a system with multiple units, the remote switch must always be connected to the master unit and the main switch of the connected unit must be in the "REMOTE" position.

The no-load power consumption of the Mastervolt AC Master 24/2500 inverter is:

In active mode: < 3.6 A at 12 V (equivalent to 1.8 A at 24 V, although the documentation specifies 12 V for consumption, the inverter is a 24 V model). In energy-saving mode: < 1.4 A at 12 V (equivalent to 0.7 A at 24 V).

The Mastervolt AC Master 24/2500 inverter has an efficiency of 88%, enabling efficient conversion of battery power to alternating current.

The AC Master 24/2500 is equipped with a jumper that enables or disables the CAN termination resistor. CAN termination is required for systems with multiple units, with one termination point at the start and one at the end of the bus. A closed jumper means the termination is active, while an open jumper means it is inactive.

The Mastervolt AC Master 24/2500 inverter has an IP21 protection rating, provided it is mounted horizontally on a wall. This means it is protected against solid objects larger than 12.5 mm and against vertically falling water droplets.

The ground terminal of the AC Master inverter chassis must be connected to the central ground point of the vehicle or boat to ensure a secure installation compliant with standards.

Mastervolt cannot be held liable for indirect damages resulting from the use of the AC Master. It is critical to strictly follow installation and usage instructions to avoid any issues.