Napájecí kabel OPC-891A

The Icom OPC-891A power cable is designed to provide direct current (DC) power to various compatible Icom marine VHF radios. It allows direct connection of the radio to a 12 V power source on the boat.

The OPC-891A cable is designed for a 12-volt direct current (DC) power supply. It must not be used with a higher voltage, such as 24 V DC, as this could damage the radio.

Installation is straightforward:

The cable has a specific connector that plugs into the power input located at the rear of your Icom VHF radio. The other end of the cable has stripped wires (typically red for positive and black for negative). These wires must be connected to your boat’s 12 V DC power source, strictly observing polarity. It is recommended to disconnect power before any connection and to consult your radio’s user manual for detailed instructions.

No, the OPC-891A cable is specifically designed with a connector and electrical specifications unique to Icom VHF radios. It is not compatible with equipment from other brands due to differences in connectors and configuration.

The OPC-891A cable is usually supplied as a standard accessory with many Icom VHF radio models at the time of initial purchase. However, it is also available for separate purchase as a spare part. It is always advisable to check the contents of your radio’s box or the product sheet for confirmation.

The OPC-891A power cable is designed for use with a direct 12 V DC power source. Since its use is strictly limited to operational testing and technical diagnostics of the Icom GM600 marine VHF, it is typically connected to a stable laboratory power supply or a dedicated 12 V test battery. It is important to note that this cable bypasses the PS-310 voltage converter and must not be used as the main power system for permanent onboard installations.

The OPC-891A cable is a direct power cable. It is designed to connect the radio directly to the boat's 12 V DC power source, not to extend another power cable.

Yes, using the OPC-891A power cable for operational power supply to the Icom GM600 VHF would impact its GMDSS Class A compliance.

The OPC-891A cable is designed to provide direct 12 V DC power to the GM600 VHF, specifically for functional test and technical diagnostic procedures. It bypasses the Icom PS-310 voltage converter.

To ensure GMDSS Class A compliance of the GM600, a regulated 12.6 V power supply is mandatory. This power supply is normally provided by the PS-310 voltage converter (used with the OPC-2352 cable). Therefore, the OPC-891A cable must not be used as the primary power system for an onboard installation where GMDSS Class A compliance is required, as it does not provide the necessary regulated voltage.

As an original Icom accessory designed for marine equipment, the OPC-891A cable is made with materials suitable for a nautical environment. However, to ensure maximum durability and reliable installation, stripped wire connections to the power source must be made securely, with proper sealing and protection against moisture and corrosion.

Yes, several precautions are important:

Ensure the boat's 12 V DC power is disconnected before making the connection. Strictly observe wire polarity: red wire to positive (+) and black wire to negative (-). Use watertight and secure electrical connections (e.g., crimped and insulated terminals) to prevent short circuits, corrosion, and fire hazards. Always refer to your radio's user manual for specific installation instructions.

No, the OPC-891A cable is a unidirectional power cable designed solely to supply power to a compatible Icom VHF radio. It cannot be used to charge a battery or for any purpose other than powering the equipment.

The OPC-891A power cable is designed to provide technicians with direct access to a 12 V DC power supply for the Icom GM600 marine VHF. Its main advantage is that it bypasses the PS-310 voltage converter, which is normally required to deliver a regulated 12.6 V DC supply (essential for the GM600’s GMDSS Class A compliance).

By using the OPC-891A, technicians can perform bench testing or maintenance without needing the vessel’s external PS-310 power supply. This simplifies technical diagnostics and testing procedures by providing a direct, dedicated power connection for these specific tasks.

It is technically possible to cut and extend the cable, but this must be done with great care by someone with marine electrical skills. Any modification to the cable could affect its performance, safety, or void the product warranty. It is preferable to use a cable of the appropriate length or consult a professional for any adaptation.

Yes, the OPC-891A is an Icom-branded factory power cable. Using factory accessories ensures perfect compatibility, optimal reliability, and compliance with Icom equipment specifications.

The OPC-891A cable and the PS-310 power supply (with the OPC-2352 cable) have distinct and complementary functions for the Icom GM600 marine VHF.

The PS-310 power supply, paired with the OPC-2352 cable, is the primary power system. It is essential to ensure a regulated 12.6 V DC power supply, critical for SMDSM Class A compliance of the GM600 during installation and use aboard the vessel. The OPC-891A cable, on the other hand, is a DC cable designed specifically for testing and technical diagnostics. It allows direct power supply to the transceiver at 12 V DC exclusively for operational verification procedures on a test bench or during maintenance interventions. It provides technicians with direct access to power without requiring the ship’s external PS-310 power supply unit. In summary, the OPC-891A is a tool dedicated to technicians for maintenance and testing and does not replace the main power system required for permanent operational installation aboard.

The OPC-891A cable itself generally does not include an integrated fuse. Fuse protection must be provided at the boat's power source, in accordance with the user manual recommendations for your Icom VHF radio. It is critical to install a fuse with the correct amperage to protect your equipment and the boat's electrical system.

No, the OPC-891A cable is specifically designed for 12V DC power. Using it with a 24V DC system will irreparably damage the Icom VHF radio. If your boat uses a 24V system, a suitable voltage converter (24V to 12V step-down) will be required to power your radio.