Fusion Signature Series 3 white 7.7" tower speakers, 280 W with CRGBW lighting

These Fusion Signature Series 3 marine tower speakers have a 7.7-inch (approximately 19.5 cm) diameter.

These marine speakers have a maximum power output of 280 Watts.

Yes, when properly installed, these speakers are rated IP65 for protection against dust and water ingress under normal conditions. Note that they are not designed to withstand high-pressure water jets, such as those that may occur when washing your boat.

The True-Marine™ certification means that the products have undergone rigorous environmental testing in harsh marine conditions. These tests ensure that the products exceed industry guidelines for marine equipment, thereby guaranteeing their durability and performance in a marine environment.

Yes, these speakers are equipped with integrated CRGBW lighting, offering a range of colors and lighting effects.

To clean your speakers, use a damp cloth soaked in fresh water to remove salt and residue. For heavy salt buildup or stains, a mild detergent may be used. Never use harsh cleaners or solvents, as this could damage the product and void the warranty.

The speaker cable is not included with the speakers. For most installations, a 16 AWG (1.31 mm²) gauge cable is recommended. For longer distances between the amplifier and the speaker, for example from 8.5 to 21 meters (28 to 69 feet) for a 4-ohm load (1 speaker), a 12 AWG (3.31 mm²) gauge cable may be required.

No, mounting brackets for FUSION marine tower speakers are sold separately. Various mounting options are available for installation on a wakeboard tower or directly on the boat's deck.

It is recommended to make all wiring connections using solder and heat-shrink tubing (not included). Use of crimp connectors is not advised due to the small hole required to route speaker and RGB LED wires.

If you choose not to install the FUSION CRGBW wireless remote, you can set the LED static color by connecting the colored LED wires directly to the negative terminal (-) of a 12 V DC power source. The black LED wire must be connected to the positive terminal (+) of the same power source, via a 3 A inline fuse.

Here are the LED color mappings:

Red: Red wireGreen: Green wireBlue: Blue wireYellow: Red and green wiresMagenta: Red and blue wiresCyan: Blue and green wiresCool white: Turquoise wireWarm white: Yellow wireDo not forget to insulate unused LED wires to prevent a short circuit.

To identify the polarity of speaker wires:

The white wire corresponds to the positive (+). The white wire with a black stripe corresponds to the negative (-).

Yes, if the speakers are installed at an angle, you can rotate the front of the speaker and the end cap so that the FUSION logos appear level. This adjustment must be performed after securing the speaker to the mast or deck.

Yes, you must connect the positive wire (+) of all speaker LEDs to a 3 A fuse located near the power source. It is also recommended to connect this positive wire (+) to the power source via an isolator switch or circuit breaker to turn the LEDs on and off.

Use 20 AWG (0.5 mm²) or thicker wire to connect LEDs to the battery.

If you experience a sound issue, check the following points:

Ensure all connections from the source device and/or amplifier are properly connected to the speaker terminals. Check that the correct wire polarity is maintained between the source and speakers (positive must connect to positive and negative to negative).

It is recommended to install a FUSION CRGBW wireless remote control (sold separately) with these speakers. This accessory allows you to turn the LEDs on and off, change colors, and create various lighting effects.

These speakers, being True-Marine™ certified products, are covered by FUSION’s 3-year limited global consumer warranty.

The warranty may be void in several cases, including:

Cosmetic damage (scratches, scuffs, dents).Damage caused by an accident, misuse, improper use, water (especially high-pressure water jets), flooding, fire, or other natural disasters.Damage resulting from service performed by a provider not authorized by Garmin.Damage to a product modified or altered without Garmin’s written authorization.Use of harsh or solvent-based cleaners on speakers.

Yes, it is strongly recommended to have your audio system installed by a professional installer to ensure optimal performance and avoid potential damage.