Marine subwoofer Signature Series 3i Sport gray 12" 1 400 W with CRGBW LED

This Fusion Signature Series 3i marine subwoofer has a maximum power output of 1,400 W.

This marine subwoofer has a 12-inch (306 mm) diameter.

The CRVBW lighting (Cool White, Red, Green, Blue, Warm White) on this subwoofer allows you to choose from multiple lighting colors. You can get red, green, blue, yellow (by combining red and green), magenta (by combining red and blue), cyan (by combining blue and green), cool white, or warm white.

Yes, this subwoofer is a True-Marine™ product. This means it has undergone rigorous environmental testing in harsh marine conditions to exceed industry guidelines for marine products.

Yes, the front face of the subwoofer is protected against water ingress. However, the rear part of the subwoofer, including all components and connected cables, is not waterproof and must be protected from moisture. Exposure to moisture on the rear of the subwoofer may result in component failure.

Yes, this subwoofer contains magnets. Caution is advised when using the product near electronic or medical devices, as the magnets may interfere with these systems.

This subwoofer is a gray Sport edition.

For installing this subwoofer, you will need the following tools:

A power drillA drill bit (size varies depending on the surface material)A saw or utility knife suitable for cutting the surface materialA Phillips screwdriverWire strippersTinned marine-grade 12 AWG (3 to 4 mm²) or thicker speaker wireAdditional tools and materials may be required for custom installations.

Yes, when selecting the mounting location, consider the following points:

The rear of the subwoofer must be protected from moisture. The mounting location must provide sufficient clearance for the subwoofer's mounting depth. A flat and vertical mounting surface is recommended for the best watertightness. The subwoofer's wires must be protected from sharp objects, and rubber grommets must be used when routing wires through panels. To avoid interference with a magnetic compass, do not mount the subwoofer closer to a compass than the safety distance specified in the product specifications. If the subwoofer is mounted in an area exposed to weather or water, it must be installed on a vertical surface. If the subwoofer is mounted outside the boat, it must be well above the waterline.

No, it is recommended to mount the subwoofer on a vertical surface if the location is exposed to weather or water. Mounting on a horizontal surface facing upward can lead to water accumulation inside and around the subwoofer, causing damage over time.

A mounting template is included in the product box. It is strongly recommended to use this supplied template. After cutting it out and verifying that it fits the chosen location, orient it so that the Fusion logo is level. Secure the template, then use a jigsaw or rotary tool to cut the mounting surface along the inside line on the template. Test the fit of the subwoofer in the cutout and adjust if necessary.

Use 12 AWG (3 to 4 mm²) or thicker marine-grade tinned copper speaker wire to connect the wiring harness to the amplifier. The speaker wire is not included with the subwoofer.

For LED lighting, it is recommended to install a Fusion CRGBW wireless remote control module. If you do not use it, you can connect the colored LED wires of the harness to the negative terminal (-) of a 12 V DC power source to set a static color. The black LED wire of the harness must be connected to the positive terminal (+) of the same power source to complete the circuit. A 20 AWG (0.5 to 0.75 mm²) wire or thicker is recommended for LED connections, and an appropriate fuse must be installed on the positive wire near the power source.

Yes, it is mandatory to install an inline fast fuse on the positive wire, at the power source end of the LED cable for each speaker. This fuse, rated at 300 mA for Signature Series 12-inch subwoofers with LED lighting, protects the LEDs and the speaker from excessive electrical current. The fuse must be installed in a fuse holder designed for marine use.

It is recommended to install a Fusion CRGBW wireless remote module with this subwoofer to turn the LEDs on and off, change colors, and create lighting effects.

The LED lighting requires a 12 V DC power source. The positive wire (+) (black) for all LEDs on the speaker must be connected through an appropriate fuse near the power source and via an isolator switch or circuit breaker to turn the LEDs on and off.