LUX SL180, riba-valgustus, CRGBW, 300 mm

The Garmin LUX SL180 LED strip provides full-spectrum CRGBW color lighting. This includes cold white, red, green, blue, and warm white. The white color temperature is adjustable from 2700 K (warm white) to 6500 K (cold white).

The Garmin LUX SL180 LED strip has a length of 300 mm. It is supplied in predefined, factory-sealed lengths and must not be cut.

Yes, the LUX SL180 LED strip has an IP68 protection rating. This means it is protected against dust and prolonged immersion. However, it is not designed to be permanently submerged in water. It can be installed in wet areas, but above the waterline.

Yes, the LUX SL180 LED strip is designed to be installed both inside and outside the vessel, above the waterline. Its material is UV-resistant and has been tested for salt spray to ensure durability in a marine environment. It should not, however, be installed in areas of direct strong sunlight.

The average power consumption of the LUX SL180 LED strip is 8.7 W per meter. Maximum current draw is 0.6 A/m at 12 V or 0.36 A/m at 24 V, via the dedicated strip driver.

No, the LUX SL180 LED strip should not be cut. It is supplied in predefined lengths and factory-sealed to maintain its IP68 waterproof rating and performance.

Each meter of the LUX SL180 LED strip integrates 180 CRGBW-type LEDs, providing full-spectrum color lighting.

Yes, the LUX SL180 light strip’s housing material is UV-resistant and has passed salt spray testing, ensuring durability in marine environments.

The LUX SL180 LED strip is specifically designed to be used only with Lumishore LUX LED strip control modules. It must not be connected to other lighting control products or third-party controllers.

No, you must not use the LUX SL180 strip with lighting controllers from other brands. It must be used exclusively with Lumishore LUX strip light controller modules to ensure compatibility, optimal performance, and warranty validity.

Before any installation, always ensure that the vessel's power source and battery are disconnected or isolated. It is also recommended that a qualified professional carries out the electrical and mechanical installation.

The strip can be installed using its integrated 3M adhesive tape. Clean the mounting surface thoroughly with IPA, then remove the adhesive backing and press the strip firmly into place, applying pressure only to the edges and not the LEDs. Allow the adhesive to cure for 24 hours before powering on the strip.

For outdoor installations in damp areas or with tight bend radii, it is recommended to use mechanical fasteners in addition to the adhesive layer. These mounting clips should be placed every 25 to 30 cm or on each side of a bend.

The LUX SL180 LED strip has a minimum bending radius of 50 mm on the vertical axis only. It must never be bent on the horizontal axis, twisted, pulled, or stretched.

For strip lengths exceeding 1 meter, it is recommended to use two people for installation: one person to install and another to hold and unroll the strip. For this 300 mm model, single-person installation is possible by following the other precautions.

Do not let the strip fall or twist during installation; carefully unroll it from the reel. Do not apply pressure on the LED area; press only on the edge of the strip. Do not pull, stretch, twist, or bend it on the horizontal axis. Ensure it is laid flat in a straight line to avoid creases or twists.

After installation with 3M adhesive, you must allow the adhesive to cure for 24 hours before powering on the LED strip.

The Garmin LUX SL180 lighting system is warranted against manufacturing defects for a period of three years from the original purchase date.

The warranty may be voided in case of misuse, abuse, incorrect installation, negligence, improper shipping, damage caused by disasters (fire, flood, lightning), installation by unqualified personnel, unauthorized repair or modification, or unapproved installations. Use with third-party autopilots not from Lumishore LUX will also void the warranty.