GT12M-THF 0°-os GT-szonda - átmenő, közepes frekvenciájú CHIRP

The Garmin GT12M-THF transducer is made of brass and is designed for installation on fiberglass, wood, or composite hulls. It must not be installed on aluminum or steel hulls.

You must not install the GT12M-THF transducer on an aluminum or steel hull as this would create galvanic corrosion. This corrosion can cause water to seep around the transducer and potentially damage your vessel.

For installing the GT12M-THF transducer in a solid fiberglass hull, you will need a 73 mm (2 7/8 inch) hole saw to drill the hole.

Yes, it is mandatory to update the software of your Garmin chartplotter after installing the GT12M-THF transducer to ensure optimal performance and full compatibility with the new device.

During installation, you must apply marine sealant to ensure a perfect watertight seal. Steps:

Apply a 2 mm (1/16 in) layer of marine sealant to the inner flange of the transducer housing where it contacts the hull.Apply marine sealant along the threads of the transducer housing to fill the gap between the threads and the hull. The sealant on the threads should extend about 6 mm (1/4 in) above the inside of the hull to seal and secure the hull nut.

For optimal hydrodynamic and sonar performance, the transducer must be mounted in an area of non-turbulent water. Avoid locations behind frames, struts, fittings, water intakes or discharges, or anything that could create air bubbles or cause water turbulence. It should also not be mounted where it could be shaken during launching, towing, or storage. On single-screw boats, ensure it is not in the path of the propeller.

The Garmin GT12M-THF, 0 degree is a through-hull transducer designed for sonar detection. It is specifically suited for installation on hulls with a deadrise angle of 0 to 5 degrees at the installation point, ensuring optimal performance.

The Garmin GT12M-THF transducer is made of brass. This material choice makes it robust for compatible hull types.

The GT12M-THF transducer is compatible with fiberglass, wood, or composite hulls. It is specifically designed for installation on these materials.

No, it is imperative not to install the GT12M-THF transducer on aluminum or steel hulls. The brass in the transducer would cause galvanic corrosion with these materials, which could lead to water ingress and damage your vessel.

The main difference lies in the manufacturing material and compatibility with hull types. The GT12M-THF is made of brass and is compatible only with fiberglass, wood, or composite hulls. The GT15M-THF, on the other hand, is made of stainless steel and can be installed on all hull types (including aluminum and steel), provided that the supplied galvanic isolation components are used for the latter.

This 0-degree transducer is designed for vessels where the hull drift angle at the installation point is between 0 and 5 degrees. For optimal performance, it is crucial to check the hull drift angle at the chosen location before installation. You can measure it with a smartphone app, an angle finder, a protractor, a digital level, or by consulting your boat manufacturer.

Yes, to achieve the best possible performance and avoid potential damage to the device or your vessel, installation by a qualified marine technician is strongly recommended.

Standard tools required for installation include:

A drillA 3 mm (1/8 in) drill bitAn adjustable wrench (suitable for nuts up to 75 mm)Marine sealant (flexible, fast-curing, for below the waterline)Mild household detergent or rubbing alcoholSandpaperMasking tapeWaterproof electrical tapeA 73 mm (2 7/8 in) hole saw for solid fiberglass hullsFor sandwich fiberglass hulls, marine epoxy resin is also required.

Yes, a software update of the Garmin chartplotter is required after installing the GT12M-THF transducer to ensure optimal performance. You can find the update instructions in your Garmin chartplotter’s user manual.

For optimal hydrodynamic and sonar performance, the transducer must be installed in an area of non-turbulent water. Below are general recommendations:

On outboard and sterndrive boats, it must be installed forward and near the engine. On inboard boats, it must be installed forward and away from the propeller and propeller shaft. On stepped hulls, it must be installed forward of the first step. It must be mounted parallel to the bow-stern axis of your vessel. Avoid areas behind stringers, frames, joints, water intakes or discharges, or any feature that could create air bubbles or turbulent water.

For a fiberglass hull with a core, preparation is crucial to prevent water infiltration:

Drill a 3 mm (1/8 in) pilot hole from the outside of the hull. Use a 73 mm (2 7/8 in) hole saw to cut the transducer hole through the entire hull from the outside. From inside the hull, use a slightly larger hole saw to cut only the inner fiberglass skin and the core, ensuring the outer skin is not cut. Seal the core inside the hole using either fiberglass and resin or casting epoxy. This step is essential to prevent water from seeping into the hull's core.

During installation, you must apply marine sealant to ensure a perfect seal and prevent water ingress:

Apply a 2 mm (1/16 in) layer of marine sealant to the inner flange of the transducer housing where it contacts the hull. Also apply a layer of marine sealant along the transducer housing threads to fill the gap between the threads and the hull. The sealant on the threads should extend approximately 6 mm (1/4 in) above the inside of the hull to seal the assembly and secure the hull nut.

Yes, several precautions are important for the durability and proper functioning of the transducer:

Never use the cable to lift or pull the transducer to avoid damaging it.Always operate the transducer when submerged. Operating it in air can damage it due to overheating.For cleaning, do not use solvents such as mineral spirits, acetone, Methyl Ethyl Ketone (MEK), or similar products, as they can cause permanent damage to the transducer surface. Also, do not use an electric sander or pressure washer.

Yes, the transducer can potentially cause cavitation if the mounting location is not optimal. It is crucial to mount it in an area of clean, non-turbulent water. On single-propulsion boats, the transducer must not be mounted in the propeller’s wash path. Cavitation can degrade boat performance and potentially damage the propeller.