Autopilotas Garmin Reactor™ 40 hidraulinėms sistemoms su prietaisu GHC™ 50

The Garmin Reactor™ 40 autopilot is an advanced navigation system designed for vessels equipped with hydraulic steering. It provides a complete solution for navigation, integrating a Course Computer Unit (CCU) and an Electronic Control Unit (ECU) to manage the boat's steering. This system is complemented by the GHC™ 50 autopilot instrument, which serves as a dedicated user interface.

The GHC™ 50 instrument is the dedicated user interface for the Reactor™ 40 autopilot. It allows configuration and control of the autopilot system. If no dedicated helm control instrument is included or installed, a compatible Garmin chartplotter connected to the same NMEA 2000 network as the autopilot’s CCU can also be used for configuration and control.

This Garmin Reactor™ 40 autopilot is specifically designed for hydraulic steering systems. Note that the hydraulic pump is not included and must be installed separately, following its own detailed instructions.

The autopilot system must be installed by a qualified marine installer. Specific knowledge of marine steering and electrical systems is required for correct installation to avoid potential bodily injury and damage to the boat.

The CCU cable is 5 metres (16 feet) long. It must not be cut. If the CCU cannot be mounted within 5 metres of the ECU, extension cables are available (sold separately) from your local Garmin dealer or at garmin.com.

For mounting the Electronic Control Unit (ECU), consider the following:

The ECU can be mounted on a flat surface in any orientation. It must be installed within 0.5 meters (19 inches) of the pump, as the cables connecting the ECU to the pump cannot be extended. The ECU must be mounted in a location where it will not be submerged or exposed to splashing.

You can use a handheld compass to test a CCU mounting location for magnetic interference. Proceed as follows:

Hold a handheld compass at the CCU mounting location.Move the compass 15 cm (6 in) to the left, then to the right, and observe the needle.Repeat this process by moving the compass above and below the mounting location.Repeat this process by moving the compass in front of and behind the mounting location.If the compass needle moves more than three degrees at any step, magnetic interference is present and you should select a new mounting location.

No, if an NMEA 2000 network is not already present on your boat, you can build one using the provided cables and connectors. The GHC™ 50 instrument and the CCU must be connected to the same NMEA 2000 network to function correctly.

Recommended tools include safety glasses, a drill and drill bits, a jigsaw or rotary cutting tool (for the optional tiller pilot), wire cutters/strippers, Phillips and flathead screwdrivers, cable ties, solder and heat-shrink tubing or waterproof butt connectors, dielectric grease, marine sealant, and a handheld compass (to test magnetic interference). Mounting screws are provided for main components.

The GHC™ 50 instrument is powered by the NMEA 2000 network and does not require a separate power connection. The NMEA 2000 network supplies power to the autopilot control unit and enables communication with other autopilot components.

The autopilot system must be configured and tuned according to your boat's dynamics. You must use the Dockside Wizard and the Sea Trial Wizard to set up the autopilot. These wizards guide you through the required configuration steps.

Yes, if the autopilot system is installed without a dedicated helm control instrument (such as the GHC™ 50 included in this pack), the initial configuration must be performed using a compatible Garmin chartplotter connected to the same NMEA 2000 network as the autopilot’s CCU.

When running the Dockside Assistant, whether the boat is in the water or out of the water, ensure sufficient clearance is provided for the rudder movement to prevent damage to the rudder or other objects. Also exercise caution to avoid bodily injury that could be caused by moving parts. If the boat is in the water, it must be stationary while you complete the assistant.

The Sea Trial Wizard configures the autopilot's core sensors, and it is critical to complete it under suitable conditions for your boat. This means the boat must not pitch excessively when stationary or at very low speed, and must not be significantly affected by wind. The onboard weight must remain balanced throughout the procedure.

The Shadow Drive™ sensor must be mounted according to the following requirements:

It must be mounted horizontally and as level as possible, securely fastened with cable ties.

It must be installed at least 305 mm (12 inches) away from magnetic materials or devices, such as speakers or electric motors.

It must be mounted closer to the tiller than to the pump.

It must be mounted lower than the lowest tiller bar but higher than the pump.

It must not be directly connected to a fitting at the back of the tiller bar. A length of hose must be placed between the tiller bar fitting and the Shadow Drive sensor.

It must not be directly connected to a hydraulic T-connector in the hydraulic line. A length of hose must be placed between a T-connector and the Shadow Drive sensor.

If compass calibration is unsuccessful, the calibration steps must be repeated. If the magnetic environment quality value displayed after calibration is low (a value of 100 indicates a perfect magnetic environment), it may be necessary to relocate the CCU and recalibrate the compass.

To avoid potential damage to the device, it is imperative to use only the screws included for its installation. Using screws other than those provided will void your product's warranty.

If you install an NMEA 2000 power cable, you must connect it to the boat's ignition switch or through another inline switch. NMEA 2000 devices will drain your battery if the NMEA 2000 power cable is connected directly to the battery.