GMR xHD2 6' radaro antena

A 6-foot antenna provides a narrower horizontal beam width compared to shorter antennas. This results in higher angular resolution and better separation between close targets, which is a major asset in congested areas or for identifying small floating objects. It also enables better long-range detection.

When selecting the mounting location, the following points should be taken into account:

The unit must be mounted out of reach of people, with the vertical beam above head height. It must be mounted high above the vessel's keel line, with minimal obstruction of the radar beam. The mounting surface must be flat or a platform parallel to the vessel's waterline and sufficiently robust to support the unit's weight. The location must allow for a connection to power, ground, and the Garmin Marine Network. Keep the antenna away from heat sources (exhausts, lights), spreaders, and mast bars. Respect the safety distance from a magnetic compass. Other electronic equipment and cables must be more than 2 m (6.5 ft) from the radar beam path. GPS antennas must be either above or below the radar beam path. The unit must be mounted at least 1 m (40 in) from any transmitting equipment and cables carrying radio signals (VHF radios, cables, antennas). It must be at least 2 m (6.5 ft) from SSB radios (single sideband).

Yes, it is mandatory to update the software on your Garmin chartplotter when installing this radar antenna. For update instructions, refer to your chartplotter's user manual.

The following tools are typically required for installing the radar antenna:

A Phillips screwdriver size #2A 5 mm Allen keyA drill with a 15.0 mm (19/32 in) bitA 17 mm (21/32 in) wrench and a torque wrenchA 3.31 mm² (12 AWG) copper wire for grounding the radar housing (and the voltage converter, if applicable)Marine sealant

The Garmin GMR xHD2 6' radar antenna uses magnetron technology. This technology is known for its ability to generate high transmission power, essential for penetrating adverse weather and detecting weak echoes at a distance.

Several safety precautions must be observed:

Avoid exposure to harmful radiofrequency (RF) levels by installing the unit out of reach of people, with the vertical beam above head height.Do not look directly at the antenna at close range when the radar is transmitting, as the eyes are the most sensitive part of the body to electromagnetic energy.Do not attempt to open the unit; it contains no user-serviceable parts. Any unauthorized opening voids the warranty.Always power off the radar before approaching the scanner for any service or maintenance operation.Be aware of high voltages if maintenance operations are required (only by a certified technician).

This radar antenna is designed for use with Garmin GMR xHD2 series open array radar systems. For optimal compatibility, it must be paired with a compatible GMR xHD2 pedestal and your Garmin chartplotter must be up to date.

The Garmin GMR xHD2 radar antenna is 6 feet long (approximately 1.83 meters).

This radar antenna uses magnetron technology. This technology is known for its ability to generate high transmission power, essential for effective detection, particularly in adverse weather conditions.

A 6-foot antenna provides a narrower horizontal beamwidth compared to shorter antennas. This results in:

Higher angular resolution.Better separation of close targets, a major advantage in congested areas.Improved detection of small floating objects.Greater ability to penetrate weather and detect weak echoes at long range.

For installing the radar antenna, you will need the following tools:

A Phillips screwdriver size #2. A 5 mm Allen key. A drill and a 15.0 mm (19/32 in) drill bit. A 17 mm (21/32 in) wrench and a torque wrench. A 3.31 mm² (12 AWG) copper wire for grounding the radar housing. Marine sealant.

When choosing the mounting location, consider the following points:

The unit must be mounted out of reach of people, with the vertical beam width above head height. It must be mounted high above the vessel's keel line, with minimal obstruction of the radar beam. The mounting surface or platform must be flat, parallel to the vessel's waterline, and sufficiently robust to support the device's weight. Avoid mounting the unit near heat sources (exhausts, lights) or at the same level as spreaders and mast bars.

After routing the cables through the mounting hole, apply marine sealant around the hole to ensure perfect watertightness and protect your vessel from water ingress.

The radar beam from this antenna extends vertically 11.5° above and 11.5° below the radar’s radiating element.

To mount the antenna on the pedestal:

Remove the protective cover from the waveguide on top of the pedestal.Align the pedestal's waveguide with the socket under the antenna, then slide the antenna onto the pedestal.Secure the antenna to the pedestal using the provided hex bolts and lock washers.Tighten the hex bolts to a torque of 0.81 kgf-m (70 lbf-in. [6 lbf-ft.]) to firmly secure the antenna without damaging the hardware.

The radar pedestal installation procedure involves the following steps:

Secure the provided mounting template to the installation surface, aligning it along the bow-stern axis. Drill mounting holes using a 15 mm (19/32 in) drill bit. If necessary, drill a 32 mm (1 1/4 in) cable pass-through hole for power and network cables.Apply the provided grease primer to half of the threads on all four threaded rods.Insert the coated ends of the threaded rods into the pedestal and tighten them using a 5 mm hex key.Raise the radar into position and carefully lower it onto the mounting surface, guiding the threaded rods through the holes.From underneath the mounting surface, install the shoulder washers, flat washers, lock washers, and hex nuts onto the threaded rods.Tighten the hex nuts to a torque of 1.5 kgf-m (130 lbf-in [11 lbf-ft]) to securely fasten the radar.

Yes, it is imperative to update the software of your Garmin chartplotter when you install this radar antenna. This ensures optimal compatibility and proper operation of the entire system.

When installing cables, note the following:

If running multiple cables through the same hole, the network cable must be routed before power and ground cables due to the size of its connector.The ground cable is not included and must be connected to a water ground, not directly to the battery’s negative terminal.Do not use voltage converters from older Garmin radar models or third-party converters. If your radar model requires a voltage converter, it must be the one supplied with the radar.The voltage converter (if applicable) requires an input voltage of 10 to 32 V DC and should be installed as close as possible to the power source.A 10 A fuse holder is required on the power cable.

To avoid interference and ensure safety, maintain the following minimum distances:

Other electronic devices and cables must be mounted more than 2 m (6.5 ft) from the radar beam path.GPS antennas must be positioned either above or below the radar beam path.The device must be mounted at least 1 m (40 in) from any transmission equipment.The device must be mounted at least 1 m (40 in) from cables carrying radio signals, such as VHF radios, their cables, and antennas.The device must be mounted at least 2 m (6.5 ft) from Single Side Band (SSB) radios.

The Garmin GMR xHD2 6' radar antenna is a key component for optimizing your radar detection system. It is designed to provide long-range detection and superior target separation, which is critical for safe navigation. Thanks to its magnetron technology and 6-foot length, it enables better weather penetration and fine distinction between objects, even the smallest ones, thereby enhancing the navigator's situational awareness.